similar to: Zap 1.4 error line 0: Unable to open

I've looked over EVERY resource I can find, but have run short of a solution. I'm running CentOS 4.4. Just installed Asterisk 1.4 and Zaptel 1.4 and libpri, but when I run ztcfg I get this error: line 0: Unable to open master device '/dev/zap/ctl' I realize this is a udev error (or from what I've read), but I cannot find out how to resolve this. I've reinstalled zaptel

Hi, I'm using zaptel-1.2.22.1 with asterisk-1.2.10 and following steps to make zaptel working... OS is gentoo linux 2006.1 Hardware: --------- 0000:05:01.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device 8085:0003 Flags: bus master, medium devsel, latency 32, IRQ 22 I/O ports at b400 Memory at ff900000

Because of a kernel upgrade i needed to recompile DAHDI. Dahdi 2.0.0 with 2.0.1 was working ok, after the reboot and compile it doesn't start anymore. Firstly it tells me it is using /etc/zaptel.conf which is deprecated, if i remove that file it complains that this file is missing..... Secondly i get an error about a missing dev file which refers to zap (which seems strange to me because

I pulled a working TE405P from one box and put it in another box. I compiled the zaptel modules, modprobe zaptel, modprobe wct4xxp, but no lights on the card come on. I do an lspci and the card shows up there. I ran ztcfg -vv and got the error message Unable to open master device '/dev/zap/ctl' so I followed the instructions in README.udev the error message went away, but now when I

I go to my Zaptel 1.4.0 folder and run ./configure; make linux26; make install and I don't see any errors. This is out of my modprobe.conf: install tor2 /sbin/modprobe --ignore-install tor2 && /sbin/ztcfg install torisa /sbin/modprobe --ignore-install torisa && /sbin/ztcfg install wcusb /sbin/modprobe --ignore-install wcusb && /sbin/ztcfg install wcfxo

I have had a TDM400 with 2 FXO and 2 FXS working for ages (>12 months). It has stopped working. All four green lights are still lit. I have rebuilt zaptel and asterisk and restarted but the problem persists. /sbin/ztcfg -vvvv Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 03:

Hello every boy again I have some problems with modprobe. When I type "modprobe zaphfc", this error happens "FATAL: Module zaphfc not found." And when I tyoe "ztcfg -vv" this error happens: Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device '/dev/zap/ctl' 1 error(s) detected Someone can help me??? Thanks to all.

I'm trying to configure a TDM808P card on debian. When I modprobe wctdm24xxp i get this error FATAL: Module wctdm24xxp not found. FATAL: Error running install command for wctdm24xxp I think i have successfully compiled the zaptel drivers, and the card appears when i do a lspci 02:06.0 Ethernet controller: Digium, Inc. Unknown device 0800 (rev 11) Subsystem: Digium, Inc. Unknown

Hello Since TDM cards are known for being particular when it comes to motherboards (PCI 2.2, etc.), I was wondering if there is a utility that can check that the Zaptel driver works OK and can tell if the TDM card is compatible? That way, if an FXO module is not reporting an incoming call, we'd know it's because of the Zaptel driver, and not something elsewhere. Are "dmesg",

Hi All; In dahdi: what we use instead of ztcfg -vv (that is existed /sbin/ztcfg -vv). ? Regards Bilal

Hi all. chan_zap not compiling, yes yes I know this sounds trivial but here me out... This morning I decided to upgrade to Asterisk 1.4.2 and Zaptel 1.4.1. I successfully installed zaptel 1.4.1 and the card is picked up and correctly configured. ztcfg shows the following: [root@zion root]# ztcfg -vv Zaptel Version: 1.4.1 Echo Canceller: MG2 Configuration ====================== Channel

i have this card installed Digium, Inc. Wildcard AEX800 8-port analog card (PCI-Express) following the steps below found on freepbx site cd /usr/src/dahdi-linux-complete-2.2.0.2+2.2.0 make make install make config /sbin/ztcfg echo "/sbin/ztcfg" >> /etc/rc.d/rc.local cd /usr/src/libpri-1.4.10.2 make clean make make install when i run make config i do not get

Hi I run asterisk 1.4.2 with zaptel 1.4.1. Zaptel is only needed for the ztdummy driver to get the Meetme() application to work. I don't have any specific hardware. And it does work nicely. When I reboot the machine however I have to manually load the driver like this: [root@vink ~]# modprobe ztdummy Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device

When booting Ubuntu 6.06.1 (Linux 2.6.15-27-386), wcfxo would load but not configure. I have three ways to manually force wcfxo to configure: 1) ztcfg, 2) modprobe -f wcfxo, or of course 3) unload and reload wcfxo. Each works equally well. As a workaround, now I have to put ztcfg in rc.local, which Debian doesn't favour. I had compiled the same zaptel under Ubuntu 5.02.0 on two

Hi, Some weird problem (or I'm too sleepy) happens with a tdm04B revision G (4fxo) Steps: modprobe zaptel modprobe wctdm ztcfg -vv /etc/zaptel.conf fxsls=1-4 # TDM04B defaultzone=us loadzone=us /etc/asterisk/zapata.conf signalling=fxs_ls group=1 context=incoming channel => 1-4 modprobe zaptel and wctdm load fine, however ztcfg -vv shows: 0 channels configured Im using centos 4.4 with

I'm trying to load ztdummy on my Asterisk, running in a XEN domain. I've modified the code to disable the use of an RTC. I can load the zaptel module just fine, the ztdummy also loads without problem. But when running ztcfg I get this error. ----- s n i p ----- graham:~# ztcfg -vvvv Zaptel Version: 1.4.6 Echo Canceller: MG2 Configuration ====================== SPAN 1: CCS/ AMI

I had a working Asterisk 1.4.24.1 installation on SUSE 9 Linux but SIP only. I then downloaded and installed latest Zaptel and could not get Zaptel working. So I downloaded Asterisk again and re-installed. But still problems: Here is my ztcfg output: asterisk:/etc/asterisk # ztcfg -vvvvv Notice: Configuration file is /etc/zaptel.conf line 4: Unable to read Zaptel version information. Zaptel

I have a TE405/TE410P card that was working on 1.0.X I upgraded the OS to Centos 4.5, Updated asterisk to 1.4 and zaptel to 1.4.5 and libpri. I copied all the zaptel and zapata and extensions.conf files from 1.0 I did update extensions.conf from 1.0 to 1.4 commands. I cannot get the card to work in 1.4.10. AHHH! I see with zttool that the T1 is in Green, I see calls coming in as the bits go

//////////////////////////////////////////////////////////////////// Hello to all, I have a question. I am installing te110p, when I give ztcfg him - v leaves the following error to me ZT_CHANCONFIG failed on channel 25: No such device or address (6) - That means east error? - It is a physical damage of the card? Thank you very much

I have a new asterisk system with a T1 card. It appears that running "ztcfg -vv " is required in order for asterisk to start properly. Is this correct? Are people adding this command to the asterisk startup script? Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL: