asterisk users - May 2007 - Module wctdm24xxp not found - TDM808P on debian

I'm trying to configure a TDM808P card on debian. When I modprobe wctdm24xxp
i get this error
FATAL: Module wctdm24xxp not found.
FATAL: Error running install command for wctdm24xxp

I think i have successfully compiled the zaptel drivers, and the card
appears when i do a lspci

02:06.0 Ethernet controller: Digium, Inc. Unknown device 0800 (rev 11)
        Subsystem: Digium, Inc. Unknown device 0800
        Flags: bus master, medium devsel, latency 64, IRQ 3
        I/O ports at e800 [size=256]
        Memory at fe200000 (32-bit, non-prefetchable) [size=1K]
        Expansion ROM at 20000000 [disabled] [size=128K]
        Capabilities: [c0] Power Management version 2

I've searched for a solution with no success. Another problem is that when i
do a ztcfg -vv i get

Notice: Configuration file is /etc/zaptel.conf
line 0: Unable to open master device '/dev/zap/ctl'

1 error(s) detected

I don't know if the errors are connected and would appreciate some help.

Thanks in advance

-- 
Juliano F. Schroeder
--------------------------------------------------
Solucionathica
http://www.solucionathica.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
http://lists.digium.com/pipermail/asterisk-users/attachments/20070511/8f1b4d9c/attachment.htm

On 5/11/07, Juliano Fernandes Schroeder <juliano7s@gmail.com>
wrote:
> I'm trying to configure a TDM808P card on debian. When I modprobe
wctdm24xxp
> i get this error
> FATAL: Module wctdm24xxp not found.
> FATAL: Error running install command for wctdm24xxp
>
> I think i have successfully compiled the zaptel drivers, and the card
> appears when i do a lspci
>
> 02:06.0 Ethernet controller: Digium, Inc. Unknown device 0800 (rev 11)
>         Subsystem: Digium, Inc. Unknown device 0800
>         Flags: bus master, medium devsel, latency 64, IRQ 3
>         I/O ports at e800 [size=256]
>         Memory at fe200000 (32-bit, non-prefetchable) [size=1K]
>         Expansion ROM at 20000000 [disabled] [size=128K]
>         Capabilities: [c0] Power Management version 2
>
> I've searched for a solution with no success. Another problem is that
when i
> do a ztcfg -vv i get
>
> Notice: Configuration file is /etc/zaptel.conf
> line 0: Unable to open master device '/dev/zap/ctl'
>
> 1 error(s) detected
>
> I don't know if the errors are connected and would appreciate some
help.
Did you "make install" in the zaptel source directory?  If you
didn't,
it didn't put the kernel modules in your kernel's module directory and
run depmod, so your system doesn't know about the modules.

On Fri, May 11, 2007 at 11:04:12AM -0300, Juliano Fernandes Schroeder
wrote:
> I'm trying to configure a TDM808P card on debian. When I modprobe
wctdm24xxp
> i get this error
> FATAL: Module wctdm24xxp not found.
> FATAL: Error running install command for wctdm24xxp
> 
> I think i have successfully compiled the zaptel drivers, 
Easy to test: run the following in the zaptel source directory: 

  ls *.ko 
> and the card
> appears when i do a lspci
The output of lspci tells you that you have a card, but is unrelated to 
the drivers you may or may not have.
> I've searched for a solution with no success. Another problem is that
when i
> do a ztcfg -vv i get
> 
> Notice: Configuration file is /etc/zaptel.conf
> line 0: Unable to open master device '/dev/zap/ctl'
I suspect that you didn't even get zaptel built.

  modinfo zaptel

Which Debian is it? Which kernel version do you use?

  uname -r

-- 
               Tzafrir Cohen       
icq#16849755                    jabber:tzafrir@jabber.org
+972-50-7952406           mailto:tzafrir.cohen@xorcom.com       
http://www.xorcom.com  iax:guest@local.xorcom.com/tzafrir