similar to: Sangoma A102 w/ EC module gets intermittent echo/audio artifacts <--followup and resolution

I think you are absolutely right. The audio I heard earlier sounds exactly like a timing issue. So: wanpipe1.conf: TE_CLOCK = NORMAL TE_REF_CLOCK = 0 wanpipe2.conf: TE_CLOCK = MASTER TE_REF_CLOCK = 1 zaptel.conf: span=1,1,0,esf,b8zs span=2,0,0,esf,b8zs I'm going to make this change and reload at lunchtime, I'll document it and post it to the list if it works.

I've replaced 2XTE110 with an A102 with echo cancellation specifically to deal with echo problems. However, user feedback has indicated to me that on some calls (not a lot, but some) the call is unusable, with audio artifiacts, described by one user, as: "very bad phasing reverb & feedback (from my rock & roll days)". This is quite intermittent, as in most cases, the user

Aha, it just happened to me, so now I can characterize the audio: It basically sounds like it's missing every other sample - fuzzy and distorted. Timing?

Hi, after many issues we finally managed to make our system do outgoing calls with perfect quality. However I cannot detect *any* form of incoming call. when I use an outside phone to call the E1 connected to the sangoma a102, I instantly get a fast busy tone. My /etc/zaptel.conf is: loadzone=us defaultzone=us #Sangoma A102 port 1 [slot:1 bus:4 span: 1] span=1,0,0,ccs,hdb3 bchan=1-15,17-31

Do you have any extension in default context of your extensions.conf file to accept incoming calls ? It must be something like; exten => 12345678,1,Answer() exten => 12345678,2,Playback(Welcome) ... 12345678 = The DID number you are calling to reach E1 Idris -----Original Message----- From: Erick Perez [mailto:eaperezh at gmail.com] Sent: Thursday, July 26, 2007 7:03 AM To:

Hi all, I've done this a few times with other PBX's but swyx has stumped me! I'm having some trouble getting Asterisk connected to a Swyx system using a sangoma A104dx... currently the setup is: BT <-> Swyx The above setup works fine... what i'm trying to achieve is BT & SIP Trunks <-> Asterisk <-> Swyx I have connected to our BT (2 x ISDN30 UK) with

I have a system that I am trying to get a port on a Sangoma A104d card connected to an Adtran 850 with 5 FXS modules and 1 FXO module. A problem I am having is figuring out what cable should be used from the port on the Sangoma to the JP2 port on the Adtran. Tried was a cross-over T1 (1->4, 2->5, 4->1, 5->2) as well as a straight T1 (1->1, 2->2, 4->4, 5->5). Neither one

Hi all, My problem boils down to these errors: ... Unable to create channel of type 'ZAP' (cause 34 - Circuit/channel congestion) == Everyone is busy/congested at this time This is triggered by lines in extentions.conf such as: exten => _X.,1,Dial(ZAP/g1/${EXTEN},,W) The system is CentOS v5.2 with Asterisk 1.4.23 (druid-asterisk-1.4.23.1-2), a Sangoma A104

I have used asterisk-1.4.14, zaptel-1.4.7, chan_ss7-1.0.0 on FC7 all went okay. using sangoma a104dx on both machine. I followed the write up on http://www.voip-info.org/wiki/index.php?page=Asterisk+ss7+setup I have the cross over cable between them. however, wanpipe shows connected but the signaling link does not align. i have my configs for host A ##wanpipe1.conf [devices] wanpipe1 =

Hi, I am trying to validate a setup with a sangoma A116 card (16PRI in one card). I currently have two machines set up, each with a sangoma A116 card. Those are interconnected with crossed PRI cables. One of them is in NT mode, the other in TE. The ports are configured in E1 mode, asterisk is all set up and I can make calls between them, filling up all 480 (16 * 30) channels. Now, I learned

I am having a problem trying to get a Sangoma A101 to work with Unicall. I have installed the sangoma drivers and everything seems to be well but when I try to run ztcfg I get the following error: CAS signalling on span 1 conflicts with HDLC with FCS check on channel 16. Here is my /etc/zaptel.conf # MFC/R2 normalmente no usa CRC4 span=1,0,0,cas,hdb3 cas=1-15:1101 dchan=16 cas=17-31:1101

Hello, We have an Asterisk 1.0.9 machine with a Sangoma A101 card fitted, it is connected to a Telstra OnRamp E1 in Melbourne, Australia. The problem we are experiencing is extreme echo and clicking noises. These are only audible to the calling party, e.g. the person calling in from the PSTN to Asterisk via the E1, the person on the SIP handset cannot hear any echo or clicking, only the

Any advise on troubleshooting this: Oct 29 02:25:58 nurscarepbx kernel: wanpipe2: OOF alarm is OFF Oct 29 02:25:58 nurscarepbx kernel: wanpipe2: RED alarm is OFF Oct 29 02:26:05 nurscarepbx kernel: wanpipe2: RAI alarm is OFF Oct 29 02:26:05 nurscarepbx kernel: wanpipe2: RED alarm is OFF It happens nightly, and I have to reset asterisk to "clear" it. Zap/Dahdi channels wont' work

Hello, We are having issues with a NEW Sangoma A108D: -- Executing [691918892 at pbx1:1] Dial("SIP/xtravoip200-009d24b0", "DAHDI/g0/691918892|30|m") in new stack [Oct 1 10:04:43] WARNING[14171]: channel.c:3170 ast_request: No translator path exists for channel type DAHDI (native 76) to 256 [Oct 1 10:04:43] WARNING[14171]: app_dial.c:1237 dial_exec_full: Unable to create

Hello, Have you tried the wanpipe-beta8c-2.3.3.tgz release in the custom/2.3.3 dir on their FTP site? Also, have you contacted Sangoma for support? They are very responsive. I am using wanpipe-beta8a-2.3.3.tgz and it's been working great on my A104 for a week now. MATT--- -----Original Message----- From: Dmitry Zhukovski [mailto:DZH@comx.dk] Sent: Monday, May 09, 2005 5:20 AM To: Asterisk

Hi, Does anybody have an idea as to why dahdi_test results drop to unacceptable levels after doing a wanrouter stop/start using a Sangoma card? See below that it drops from 99.99% to 98.55%: [root at bin]# dahdi_test Opened pseudo dahdi interface, measuring accuracy... 99.999512% 99.992874% --- Results after 2 passes --- Best: 100.000 -- Worst: 99.993 -- Average: 99.996193, Difference:

Ok, I have tested with almost all versions both in 2.3.2--*-stable and 2.3.3-*-beta - I am getting same messages: May 9 10:55:26 WARNING[3961]: chan_zap.c:1925 pri_find_dchan: No D-channels available! Using Primary on channel anyway 16! and same Down state pb01*CLI> pri show span 1 Primary D-channel: 16 Status: Provisioned, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7

Shortly, I'll be purchasing a Sangoma A102. I'm wondering if I should spring for the hardware echo cancellation circuit or not. Upon initial implementation, the 2 T1 Ports will be used as a passthrough as we slowly transition off of a legacy PBX. Eventually, we'll only be using one of the ports, and will be providing VoIP service to a bunch of SIP deskphones. So - with that usage

Hi again, Well - I didn't see beta8a-2.3.3 in custom dir. Will try. Also I tried to contact Sangoma - they are very fast to answer but main problem is time difference - it's 6 hours between Canada and Europe. Br, dmitry Dmitry Zhukovski System developer ComX Networks A/S Naverland 31, 2 DK-2600 Glostrup Denmark Phone: +45 70 25 74 74 Fax:???? +45 70 25 73 74 Web: www.comx.dk

Hello, in our company we are trying to do this: Fax <--> Traditional PBX <--> Asterisk <--> PSTN In practice, we have put an Asterisk equipped with a Sangoma A102 (2 PRI ports) between our PBX (Siemens HiCom) and the PSTN in order to have a VoIP network along the traditional telephony network. The problem is with the fax. We just want to send and receive faxes from/to our fax