similar to: Can't make outgoing calls (T100P)

Hi, I use: Trixbox-2.2.4 FreePBX-2.3.1.0 Asterisk-1.2.17 BRIstuffed-0.3.0-PRE-1y-e Zaptel-1.2.19 ..with two ISDN cards, often but occasionally the dial out failed but is possible to receive external call. My zapata.conf conf is: [trunkgroups] [channels] language=it context=from-pstn signalling=bri_cpe_ptmp rxwink=300 pridialplan=unknown prilocaldialplan=local switchtype=euroisdn

I am having problems sending and receiving calls over the T1. They never seem to connect - outbound keeps ringing, inbound gets busy. The T1 looks ok - no errors on the line. Any ideas on what is wrong? I have tried a variety of fxsks and fxoks configurations without avail. This is a single asterisk@home system with a single T1 card. Robbed Bit T1 ami, d4. ------------------inbound call

I figured it out. The old system (Televantage 3 and 4 I think) has limited specifications on the T1. After setting up the system, I was able to send and recieve calls. I still have some work to do like figuring out faxing and a floating receptionist, but this is a nice start. ----------------------------------------------------Televantage T1 Requirements: Framing: D4 Superframe or Extended

I'm having trouble getting outbound calls going with aah 1.3 and a tdm400p w/ 4 FXO. Incoming calls work fine, outbound I get this: -- Executing SetVar("SIP/231-af2b", "OUTNUM=6643955") in new stack -- Executing Cut("SIP/231-af2b", "custom=OUT_1|:|1") in new stack -- Executing GotoIf("SIP/231-af2b", "0?19") in new stack

Hello everybody, and first of all sorry for my poor English. I'm having trouble with Quadbri installed on Asterisk 1.2.17-BRIstuffed-0.3.0-PRE-1y-e. Everything is working fine, except calling to switched off or "out of coverage" cell phones. In this case I have to wait 40 seconds until Asterisk tell me that "all circuits are busy now" instead of receive cell phone

Dear All, I have an asterisk server version 1.2.12.1 along with trixbox and I am having this nasty problem, I have a TE200P and have an E1 pri attached to it and zttool says it's OK, I have configured the whole 31 channels into one group as follow: Zapata-auto.conf: callerid=asreceived signalling=pri_cpe switchtype=euroisdn context=from-zaptel group=0 channel=>1-15,17-31

On Wed, Jun 16, 2010 at 4:35 PM, Shina Owolabi <shinacalypse at gmail.com>wrote: > Hi! > I've installed Asterisk 1.4.32 with freepbx-2.6.0 in an attempt to provide > a conference bridge for an existing Avaya PBX. I have no control over the > Avaya system, but I am able to speak with the admin in charge when I need > stuff done. I am running all this in a VirtualBox

Hi All, It's broken !! (drat) Asterisk if failing to load with the following error (taken from end of /var/log/asterisk/full) after adding bristuff. Can anyone help please? Jul 17 19:57:54 VERBOSE[2503]: == Registered channel type 'Phone' (Standard Linux Telephony API Driver) Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so]Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so] =>

I have an Asterisk@Home 1.3 server (Asterisk 1.0.9) and recently added a TDM400P with (1) FXO card on port 4. Inbound calls are always successful but outbound calls fail 75% of the time with intercept messages from my dial tone provider that include "we're sorry, your call did not go through", and "we're sorry, when placing a local call it is now necessary to dial an area

hi i've configured a TE205P on asterisk at home this is my zaptel.conf span=1,0,0,ccs,hdb3,crc4,yellow span=2,0,0,ccs,hdb3,crc4,yellow bchan = 1-15, 17-31 dchan = 16 bchan = 32-46,48-62 dchan = 47 loadzone = it defaultzone = it and my zapata.conf signalling=pri_cpe ; pri_cpe = PRI slave ; pri_net = PRI master switchtype=national usecallerid=yes hidecallerid=no callwaiting=yes

i have a prablom here, i want to send a call from A to B use sip trunk , the call can sended B,but not work to PSTN. the message from B server. help pls,what's rong? > > <--- SIP read from 192.168.0.176:5060 ---> > INVITE sip:15921256331 at 192.168.0.151 <sip%3A15921256331 at 192.168.0.151>SIP/2.0 > Via: SIP/2.0/UDP 192.168.0.176:5060;branch=z9hG4bK51a51b96;rport

Hi all, I have some problem to send a FAX to a given number. I use asterisk 1.2.18, on a openSUSE 10.2, i586 host. The FAX is sent out via an ISDN PRI interface, I'm in Germany, and the destination FAX devices are in Germany too, but in different areas, so I have to use a city prefix. I did set the pri device in debug mode, below are two calls, to two different FAX numbers, the first is

Nik, Just curious - what is your telco setup? Do you have PRI with the specified D channels? You need to make sure that your telco is set up to have the D channels on 16 and 47. When you first start Asterisk, or when you log on to the CLI, do you ever see messages stating the B channels are successfully started? Let us know. -MC -----Original Message----- From:

I have an eight channel fxo setup (2 TDM400P cards) and I have them setup. Here are my configs: Zaptel.conf: fxsks=1-8 loadzone=us defaultzone=us Zapata.conf: [trunkgroups] [channels] musiconhold=default rxwink=300 ; Atlas seems to use long (250ms) winks usecallerid=yes hidecallerid=no callerid=xxxxxx callwaiting=yes busydetect=no callprogress=no usecallingpres=yes callwaitingcallerid=yes

I have call center PCs that switch between an IBEAM SIP softphone and a NEBU IAX softphone (for reasons that aren't germane here). The SIP softphones work fine, but the IAX softphones get a fast busy unless I give them an IAX trunk to use, instead of the PRI trunks that all the other phones are using. I am using Asterisk 1.2.3. svn rev 47264. I've appended a sample call trace. The

I have a PRI connected to a traditional PBX using NI-2 and a typical config (further below). When I call from a SIP/IAX phone to an extension on the PBX, only the number makes it through. If I plug that same port on the PBX to a carrier the PBX presents both name and number. Hints or pokes to relevant chapters in documentation? My config is essentially like one found here:

Hi all, I have TDM2406E with 24FXO ports connecting to 10 POTS line sitting in my office. the out going calls symptom like when called party pickup the phone but the calling party still hearing the ring tone from the IP phone. Please light me up. it been many sleepless night by googling around trying to get the right answers. The digium card running on Intel 915G chipset. Below are my zaptel

Hello, Sometimes the call gets answered for 1 second, but actually the phone has not rang, it?s just the CDR, and asterisk hangup automatically, I cought the log of 1 call like this, I hope you can help me with this. My setup is : <vendor> ----SIP--? <Asterisk> ?----IAX2---? <Asterisk with Dhadi channels> Here: -- Executing [966505103150 at from-internal:1]

In the process of turning up a new pri. Zttool indicates the T1 is ready with no alarms. asterisk*CLI> pri show span 1 Primary D-channel: 24 Status: Provisioned, Down, Active Switchtype: National ISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 10000 T305 Timer: 30000 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3

Hi *, now for a long time i am trying to set the outgoing callerid, without luck. I am here in Germany, my asterisk has a pri interface connected to a PMX installed by Telekom. All telephone calls are preselected to EcoVoice. I am using asterisk 1.2.7.1, zaptel 1.2.5 and libpri 1.2.2. A week ago we tried with a device able to simulate a telephone system so send out a callerid, and that