similar to: Problem: 2 second silence at the beginning of most calls

Hi, I've recently bought new Polycom 501 phones, upgraded to bootrom 3.2.2 and SIP 2.0.1. I just noticed something, which I first blamed on Asterisk and NATs (a 2 second silence at the beginning of a call). Something I've noticed also on my old phone (which is having the same problem now, but its also been upgraded). My keys are sticky. Simple as that. Sometimes I press a number

Hello everyone, Please forgive the exclamation points but I have been battling this one off and on for about four days now. Sorry for the cross post. It all started with a box of IP 501s. I contacted my reseller and obtained the latest BootRom and SIP firmware. Unzipped, configured, copied over to my FTP server (running AstLinux, of course). The phone booted, so far so good. Updated

Docs? Polycom has docs? Where would one find this fabled land of... err I mean Polycom does stating what ftp servers are supported? Doug. -----Original Message----- From: Ken D'Ambrosio [mailto:ken@jots.org] Sent: Tuesday, March 07, 2006 12:12 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Cc: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re:

I have a question about DHCP and boot server supporting more than 1 model of Polycom phones. According to Polycom "standards", Polycom phone boots up to get a DHCP address and at the same time getting a boot server string (with username and password) to logon to boot server to download SIP, bootROM and etc. That is okay if there is only one type of phone (that requires a specific SIP

I have been struggling over central provisioning for quite some time. I have eagerly watched each post with like problems but have yet to find a reliable answer. I have a Polycom 501 and I am trying to provision from an FTP server, and just to take any routing out of the issue it is on the same subnet. I am running the 2.0.1.0291 firmware and 3.2.2 bootrom. I set the IP info on the phone and

Giorgio, I'll answer in reverse order: I've not had reports of "noise" from my users. However, when I went down to get the s/w version from the phone that seems to be acting up the most, the user reported that earlier they were actually on a call that was ok then spontaneously dropped the audio. Per my instructions (based on another similar report I read on Digium's site),

Hi All, We are in search of the latest Polycom firmware SIP 1.6.5 and BootROM 3.1.3as per http://www.polycom.com/resource_center/1,,pw-492,00.html Can someone help? We have legitimately obtained these phones but even our official distributor can't get their hands on updated firmware. The only thing we have found is http://www.freedomphones.net/polycom/files/?M=A which has only old versions.

Hey all, Just getting started playing around with my Polycom 600. According to the wiki, it looks like it's recommended to run BootRom 2.6.1 and SIP 1.4.1. Is that info still current, or is it safe to upgrade to 3.0.1 and 1.5.2? Justin --

We are having an issue that I have been unable to figure out how to resolve. I think its related to the Polycom Phones and not the Asterisk configuration, but I'm not positive. We have several Polycom 500/501/601's on both a LAN and at employee homes. The problem we are having is if our internet connection goes down the Local LAN phones loose their connection to the Asterisk Server.

I'm having problems updating my bootrom to the latest (3.2.2) version. Basically, my phone starts downloading the bootrom, but I am completely certain that it doesn't actually complete the process. It gives me an "error updating bootROM!" message, but it only takes about 2 seconds to complete the download (which, because of my WAN link and FTP server environnement I know is

From what I know this log show everything working Perfect. Then it goes to the Welcome screen then after a long time of processing, it errors out with a 0x10000 error Any Ideas? 1005195711|so |4|00|---------- Initial log entry ---------- 1005195711|so |4|00|+++ Note that bootrom log times are in GMT +++ 1005195711|hw |4|00|Initial log entry. 1005195711|wdog |4|00|Initial log entry

Hi all, I have a Polycom Soundpoint IP 600 that looks like it is fried. It either has a bad or corrupt bootrom (I'm guessing). It never gets to the prompt that asks if I want to enter the setup configuration or continue booting. When plugged into power, it turns on, shows the Polycom logo for 3 seconds and then pretty much goes dead with two red lights on. The one in the top right corner

Hi, I have a Polycom 501 that is currently unusable because I started a firmware and sip upgrade that I can't complete. The Ubuntu box address is set static at: 192.168.1.101. The phone address is set static at 192.168.1.51. The phone settings for the server menu are: Server Type: Trivial FTP Server Address: 192.168.1.101 Server User: PlcmSpIp Server Password: PlcmSpIp (not sure what it

I am having the same issue as below. Has this issue been solved or does anyone know an answer? This error recently began and we have multiple phones out of commission. PLEASE HELP!! http://lists.digium.com/pipermail/asterisk-users/2006-August/162841.html How did you find out about 468*??? It's sure as poop not documented in the Polycom Admin Guide anywhere. -----Original Message-----

I'm setting up a new Asterisk system on a Dell server and I'm getting "fuzzy" voice between the Polycom IP SoundStation 550 and the Asterisk server. I've checked all of my codec settings and both the Asterisk and the Polycom agree on u-Law encoding. I'm using the latest release of the Asterisk code (1.4.17) and other software. If I call between phones (i.e. two

Hi, I have a really strange problem with a Polycom 430 phone and Asterisk 1.4.20. Currently If I dial the Polycom from my mobile phone answer the call on the Polycom and then hangup the mobile the call ends fine on the Polycom. But if I call from the Polycom to my mobile and then I hang up the mobile the Polycom thinks the call is still active. However doing a show sip channels shows the the

I'm trying to develop a company phone list accessible via the minibrowser feature on the phone. The pertinent section of ipmid.cfg is as follows: <microbrowser mb.proxy=""> <idleDisplay mb.idleDisplay.home="http://server/polycom/index.html" mb.idleDisplay.refresh="300"/> <main

Hi All, I am a remote office that is connected to my office via openvpn on UDP. Voip has always worked well (after discovering g729). Initially I used a softphone, then an analog set on a sipura 2000, then a polycom IP500 (I still LOVE this phone). At that point, I started noticing that the polycom doesn't ring a lot of the time. Since I was desperate for a phone, I didn't upgrade

Hello all, We have an Asterisk server that has worked without issue for a while. Before, only Sipura and Polycom 500 series phones were used. Recently, we've added a few POE switches and 20 or so Polycom 330's. The 330's seem to lock up often. One easy way to do this is by hitting the * key. I looked thru the XML files for dialplan and what not, nothing stood out.

Ever since I upgraded my Polycom 500 to the newest sip.ld (kept the old bootrom), when I dial things like "*98" for voicemail, the screen shows "9*8" and doesn't dial my voicemail system! Is this user error, or errors in the new firmware? Chris Coulthurst chris@shuksan.com -------------- next part -------------- An HTML attachment was scrubbed... URL: