similar to: ISDN-BRI issue

Hi, I'm trying to install a Junghanns quadbri for a few days but i stay with an asterisk error. (Everyone is busy/congested ) Asterisk is working with a Fritz PCbut from one year and now i want to add the quadbri. The quadbri card has been configured in NT mode and with no 100 ohms S/T termoination. (I'm not sure if the S/T parameter is correct) I have installed the bristuff package

Hi everyone. We have a problem here... Hope somebody can give us some hints. We have a HP ProLiant DL180 G6 Server with a Debian/Lenny sytem. Asterisk 1.4.21.2 (1.4.21.2~dfsg-3+lenny1) with zaptel (1.4.11) and libpri (1.4.3) is installed. There is a QuadBRI-Card installed: # lspci -vv -s 06:04.0 06:04.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)

Hi, I have installed a quadBri card, with Asterisk-1.0.10 and the bristuff-0.2.0-RC8s (* 1.0.10) When calling 0207654321 the following happens: -- Executing Goto("Zap/1-1 ", " salsa-helpdesk-day|s|1 ") in new stack -- Goto (salsa-helpdesk-day,s,1) -- Executing Dial ("Zap/1-1 ", "Zap/g1/0201234567|30 ") in new stack -- Requested transfer capability:

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable

Hi, I have a Junghanns QuadBri installed and seems to be detected and working correctly using the wcb4xxp driver All ports are configured as TE The problem is when I connect an ISDN line - the LED turns green and Dahdi status shows Alarm OK But when I try to make a call I get "All circuits are busy" cause 27 I have searched and web and tried numerous configs but it doesn't want to

Hi, we are trying to install Junghann's quadBRI into Dell PowerEdge 2800 system without success. I don't know if the issue can be that Junghann's card fits 32-bit slot and Dell PE 2800 has only 3 PCI-X 64-bit slots. Can this be an issue? We get "CRC errors for HDLC frame" when the card is initialized. Any idea what can be wrong? 1/ We use latest bristuff packages. 2/

Hi, I'm trying to dial from one Asterisk box to a Patton 4638 BRI gateway. I'm only getting this : [May 8 15:08:24] WARNING[16797]: app_dial.c:1547 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) My setup is : Asterisk 1.6.1.18 libpri 1.4.10.2 1 Junghanns QuadBRI PCI-E express with : - driver

Hello everybody, and first of all sorry for my poor English. I'm having trouble with Quadbri installed on Asterisk 1.2.17-BRIstuffed-0.3.0-PRE-1y-e. Everything is working fine, except calling to switched off or "out of coverage" cell phones. In this case I have to wait 40 seconds until Asterisk tell me that "all circuits are busy now" instead of receive cell phone

Hi All I have a Junghanns BRI 4 port installed where only the first channel of each line is working i.e. channels 1 and 4 work but 2 and 5 don't. Our config is the same on this box as 15 other similar installations where all works well. the only error I see is in /var/log/messages: Jun 28 15:49:31 pbxct kernel: qozap: CRC error for HDLC frame on card 1 (cardID 0) S/T port 2 Jun 28 15:51:27

Hi, I configured an asterisk box with 1 Digium Wildcard TE110P T1/E1 Card 0 I setup the jumper in e1 position. my zaptel.conf : defaultzone=it loadzone=it #gestione PRI span=1,0,0,ccs,hdb3,crc4,yellow bchan=1-15 # set this to 1-15,17-31 for E1 dchan=16 # set this to 16 for E1 bchan=17-31 # set this to 1-15,17-31 for E1 # Asterisk starts correctly, I see th 30 channels. Anyway I cannot put

I have configured /etc/asterisk/zapata.conf, but now Asterisk refuses to start: Asterisk 1.0.9, Copyright (C) 1999-2004 Digium. Written by Mark Spencer <markster@digium.com> .... [chan_zap.so] => (Zapata Telephony w/PRI) == Parsing '/etc/asterisk/zapata.conf': Found Sep 16 20:36:51 ERROR[6750]: chan_zap.c:6246 mkintf: Unable to get parameters Sep 16 20:36:51 ERROR[6750]:

Hi all, Using Asterisk 1.0.10-BRIstuffed-0.2.0-RC8q with a Junghanns quadBRI (2 spans connected) and a Digium TDM400 for extensions Shouuld I be worried about these lines that keep showing up in my /var/log/messages? qozap: dropped audio card 1 cardid 0 bytes 6 z1 10 z2 116 qozap: dropped audio card 1 cardid 0 bytes 6 z1 50 z2 28 qozap: dropped audio card 1 cardid 0 bytes 6 z1 59 z2 37 .. ....

Hello. I have a TE212 configured in E1 mode. This is shown in a cat /proc/zaptel/2 and 3 (where the card is configured): cat /proc/zaptel/2 Span 2: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" HDB3/CCS/CRC4 RED NOTOPEN 25 TE2/0/1/1 Clear 26 TE2/0/1/2 Clear 27 TE2/0/1/3 Clear 28 TE2/0/1/4 Clear 29 TE2/0/1/5 Clear 30 TE2/0/1/6 Clear

hi after some testing with A@H, i've decided to install my asterisk server on a slackware (because it's my favourite distro and it is still suggested here http://www.voip-info.org/wiki-Asterisk+Linux+Slackware) , so, i've installed the last 10.2 release, and i've recompiled the 2.6.15.4 kernel. then i've downloaded asterisk1.2.4 and zaptel1.2.4 i load module zaptel and

I just managed to put in a TE410 card in an Asterisk box to work with OnRamp 20(E1 downunder). I am able to dial in but was not able to dial out. Can anyone offer me some advice please? In my extensions.conf, I just put in: [default] ... exten => 0,1,Dial(Zap/g1) and I get this on the console when I dialled 0. -- Executing [0 at default:1] Dial("SIP/5166-b76004f8",

Hi, I have a working Asterisk 1.2 server on kernel 2.6.22 with the OSLEC echo canceller on a Digium PRI card. I recently switched to kernel 2.6.23 with the MG2 echo canceller (nothing else changed). Each time I try to establish a call on the PRI line I get a congestion signal. in /var/log/asterisk/full: Feb 20 08:09:43 VERBOSE[10657] logger.c: -- Executing

I installed the QuadBri card in my * server. I'm installing * on a RedHat 9 server I run the install.sh file. So far no problems. If I try to start /sbin/ztcfg -v -c /etc/zaptel.conf I will see the following error: Zaptel Configuration ====================== SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 2: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 3: CCS/ AMI Build-out:

Hope this is the right place to report/ask for help... Have have a 1.2.7.1 installation running reasonably happily for a while. Thought we might give 1.4.0b3 a go. Ran it on a local test machine (that has the single port card) and all was well. However, when I run it on a machine with the 4-port card, it has trouble with Zaptel. I attach some diagnostics and welcome any suggestions (including

I am unable to make quadbri board to work in NT mode, in TE mode it works OK. I have set 5 jumpers to NT mode. Dmesg shows everything OK: qozap: Junghanns.NET quadBRI card configured at mem 0xd084e000 IRQ 9 HZ 100 CardID 1 qozap: S/T ports: 4 [ TE TE TE NT ] qozap: 1 multiBRI card(s) in this box, 4 BRI ports total. from Asterisk side seems to be ok. pri show span 4 Primary D-channel: 12 Status:

Hi, I'm trying to connect a PC with a TE410P to an E1/IP equipment. Unfortunately I keep getting a yellow alarm from zaptel (in zttool) and a Loss of Framing alarm on the remote equipment. The E1/IP is connected on the other side to a PRI interface on a GSM MSC. I have configured the span as: span=1,1,0,ccs,hdb3 (also tried span=1,0,0,ccs,hdb3) and the channels as: bchan=1-15,17-31