similar to: siemens hipath interoperability - PRI/Q.SIG - card recommendation

Hello! Is it possible to connect Siemens HiPath 4000 to Asterisk? What equipment required on Siemens side? I mean IP not E1. Sorry for asking here. Siemens-related websites use "salesperson language". There is no technical information.

Hi all, I have a connect between a siemens hipath & Asterisk system over PRI The connection works perfectly I can call from the Hipath to an Asterisk Extension. I want to allow the hipath extensions to dial out over a SIP trunk on asterisk but I keep getting "The number you have dialed is not in service" In this CLI I'm dialing from hipath extension 9 (prefix for sip trunk)

I am connecting to a siemens hipath 4000 with dahdi 2.1.0.4 and asterisk 1.4.23 using a Te210P card. the phone guy is saying that the lines are reporting always BUSY. however on my end the status shows OK. Anyone seen this? Is there something different about connecting PRI to siemens hipath? system.conf shows: loadzone=us defaultzone=us span=1,1,6,esf,b8zs bchan=1-5 dchan=24

Hi * :-) I found in the online WiKi docs some information on how to integrate Asterisk with "old PBX"... http://www.voip-info.org/wiki-Asterisk+legacy+integration ...but I couldn't find anything on integration with a Siemens HiCom 150E. Later on we'll migrate to a HiPath 3750 so information covering this model would be nice too... Do you know if any of the PBX listed

Hello all, I am trying to connect asterisk to a Siemens Hipath 3750 PBX system. I have a physical connection issue. I know that I should use a crossover RJ48 cable to link the two systems. The problem however is that the physical interface of the Siemens system is very unfamiliar. From my digging around, I think that this is an S2M interface. http://www.mail-archive.com/asterisk-users at

Hello all. I have installed and functioning asterisk-1.2.9.1 where I effected one upgrade in asterisk-1.0.9, is interconnected with a PABX Siemens HiPath 4000 in ISDN PRI with protocol QSIG, the one that is happening he is that the calls originated for PABX Siemens and destined to SIP phones asterisk are being without audio, nor Ring, is dumb. They could help in this case me? Best Regards Josu?

Hello all. I have installed and functioning asterisk-1.2.9.1 where I effected one upgrade in asterisk-1.0.9, is interconnected with a PABX Siemens HiPath 4000 in ISDN PRI with protocol QSIG, the one that is happening he is that the calls originated for PABX Siemens and destined to SIP phones asterisk are being without audio, nor Ring, is dumb. They could help in this case me? Best Regards Josu?

Hi Stephen, You said that PRI works great. We are using HiPath 3550 and Siemens digital phone which using *11, *97 etc for function keys. However Asterisk uses the the * key plus one or two digits for function keys as well(it is common key combination for functions). So is it any way to disable *11, *97 keys in HiPath system and pass this keys to Asterisk? Thanks and regards, Isaac >Hi

Hi all, I'm trying to setup Asterisk trunk to Siemens HiPath 4000 V2.01 What would be the best way to do so? I am a bit confused because as far as I've understand this PBX doesn't support H323, but I saw somewhere someone who created a cornet trunk and it worked using H323. So if anyone knows what I need to configure I would appreciate it. I've read some information

Hi, I will like to know if anyone would guide me about how I can to interconnect one SIEMENS HiPATH 3700 with Asterisk. HiPATH have VoIP card and my idea is to do one un IP trunk between them so we would to transfer calls and services (voicemail, IVR,..) between both. We havent PRI ports unused in HiPATH so cheapest method of interconnection is one IP trunk. Any help or comment about will be

I am connecting 1.4.22 and dahdi 2.1.0.3+2.1.0.2 to a siemens hipath 300 and siemens hipath 4000. (2 channels to each switch) with a TE210p card setup as T1 with em_w. When the call is initiated to either switch the phone rings, when its answered then nothing... I hear no audio etc... After the timeout period the call is hung up. The phone switch 300 needs the T1 reset as the channel is not

Hi all, I want to use asteriks with my siemens hipath 1120 hardware. Is it possible? Thanks -- /** * @AUTHOR At?f CEYLAN * Software Developer & System Admin * http://www.atifceylan.com */ -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20101125/a5b9e9f6/attachment.htm

My new company is going to enter a bid competing with 3Com and Siemens solutions from others. Voice service is a PRI T-1 with a block of 100 DID numbers, a second T1 that will carry Integrated voice/data, 12 voice/768K for redundency. I asked this a week or two ago, now I have more details. Best/$ channel banks that work with Asterisk and Best deal on phones... 16 business, 34 basic IP

Hello all, I'm new to asterisk. Our company wants to setup an asterisk server and will eventually move to IP centric phones, but they don't want to just throw away the old Siemens PBX, so during the process we want to integrate it with asterisk. Is it possible? and how? thanks. Lito -------------- next part -------------- An HTML attachment was scrubbed... URL:

The last post I saw regarding this was June 2003 (before my time with *, I started in September): http://lists.digium.com/pipermail/asterisk-users/2003-June/013324.html Is there any support for Q.SIG in * at all? The Norstar MICS uses a MCDN (Meridian Customer Defined Network) key to enable the "SL1" protocol which from everything I've been reading is just Q.SIG. This protocol

Hi all, I'm planning on connecting our Asterisk to our legacy PBX (an Avaya INDeX). I was originally going to sit it between our ISDN connection and the INDeX (tried it, worked ok) but now I intend to hang it off a spare PRI card just so should the * fail we keep our ISDN's at the INDeX, yes I've looked at ISDNguard but little info from the manufacturers. Anyhow, I'm now

I've been trying lots of configurations now. And the problem that I can't solve is this: I have a Digium T205P card. I have connected one of the connections to our internal PBX (NEC 2000 IPS). The Asterisk is configured as pri_cpe, and the NEC is configured to be the network side of the connection. Both ends are using b-channels 1-15 and 17-31, the d-channel is on 16. When I start

After lots of testing I discovered that I could get the sound to work. The only thing I had been testing was MeetMe and Voicemail. But when I dialed a SIP-phone, or routed back to other phones via the PRI interface, everything works just great! The problem only seem to occur when dialing directly into Asterisk, when Asterisk sends the audio output. I have also discovered that the PRI never seem to

Hello, I am using a Cisco-2,811 as a gateway between the Asterisk PBX and our Nortel TX-1 university's PBX. It is working but no names are exchanged. From the debug mode I see that the Cisco sends the display name (which does not appear on the Nortel's phones) and the Nortel does not bother to send it at all. I recall that when I had a pilot with Cisco CCM two years ago we had to set

Hello everyone, My setup: Debian squeeze Asterisk 1.8, DAHDI, libpri, compiled from source TE110P, attached to a Deutsche Telekom Octopus E Modell 300/800 I'm trying to get MWI for Voicemail working. In the same server I have also got an Eicon DIVA PRI card for testing purposes (it is integrated via CAPI and the chan-capi channel driver into my Asterisk). MWI works just fine there. I