asterisk users - Dec 2005 - [offtopic] Asterisk <-IP-> Siemens HiPath 4000

Hello!

Is it possible to connect Siemens HiPath 4000 to Asterisk? What 
equipment required on Siemens side? I mean IP not E1.

Sorry for asking here. Siemens-related websites use "salesperson 
language". There is no technical information.

On Wednesday 21 December 2005 14:47, Dmitry Ivanov
wrote:
> Hello!
>
> Is it possible to connect Siemens HiPath 4000 to Asterisk? What
> equipment required on Siemens side? I mean IP not E1.
I am also to deal with HiPath, but 3750. 
I came to the conclusion that buying anything on the HiPath side
is stupid. A Digium TE110P or Sangoma101(both PRI) would deliver E1
(31channels) to HiPath and use it as a "channel bank".
A card as th above would cost you about $600 but buyin analog modules
could be expensive.
But, please, any other opinions are highly appreciated.
benchev

Hi,

we have interconnected Asterisk with a HiPath4000 V1.0
using a H.323 Trunk. You have to install the oh323
channel from [1]. On your HiPath4000 V1.0 or V2.0 you
need a HG3550 board for IP-Trunking.
If you have the version 3.0 then the HiPath supports
SIP-Trunking but i have not tested it yet.

otherwise you can interconnect Asterisk with HiPath
using ISDN. I have in addition to the h323 Trunk a
backup trunk using a Diva Eicon 4 Bri (chan_capi) and
it works fine too. I suppose it will work with Digium
cards too.

[1]http://www.inaccessnetworks.com/projects/asterisk-oh323



--- Dmitry Ivanov <dimss@telecentrs.lv> wrote:
> Hello!
> 
> Is it possible to connect Siemens HiPath 4000 to
> Asterisk? What 
> equipment required on Siemens side? I mean IP not
> E1.
> 
> Sorry for asking here. Siemens-related websites use
> "salesperson 
> language". There is no technical information.
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com
> --
> 
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
>   
>
http://lists.digium.com/mailman/listinfo/asterisk-users
> 

__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com

Hi Nguyen ,
I haven't got the opportunity to make my project real due to business
obstacles, but I still think that it should work.
All that follows is a theory, but there are guys on the list that
might help you with more practical advises.
> I have stuck with Hipath 3750 and Asterisk + TE110P. I don't have the
> manual of Hipath 3500 yet (have to buy from local vendor), so I was not
> sure are these thing possible
>
> Scenario: Asterisk|TE110P->TMS2|Hipath 3750 ->(16 CO lines) PSTN
I had the same idea because I wanted to save on the card side(single span), 
and use  the Hipath as a "channel  bank" :-)
> - Is this possible for Asterisk Users call out using CO lines? Some of
> Siemens guys told me that I need an DISA card for this? Is this true?
Most of the time the Siemens guys don't know what is Asterisk.
Basically TE110P *is* a DISA since it gives Direct Inward System Access
(if this is what they mean by DISA)

Below is a threat I found with exactly the same scenario like yours:
http://lists.digium.com/pipermail/asterisk-users/2005-April/093761.html
And this proves that the idea must work.
> - When the call arrived from PSTN through CO line, can it be forwarded to
> Asterisk? Again, they says that we require the DISA card.
As far as anything gets into Asterisk then you are free to do whatever you
want. I don't know what DISA they are talking about? Do they mean S2M
or similar thing(but TMS2 is S2M)?
 Anyone?

Sorry for not being able to help, but hope somebody else
would do it.

Benchev

Hi Josue and ISDN experts,
I spent 2 days doing some home works on connecting TMS2 and Sangoma A101. So
far, it's just partially worked.

I was not sure, what's correspond to EuroISDN in Siemens language. On
Hipath3750, I see a bunch of protocol listed:

- AmtPP with CRC4
- AmtPP without CRC4
- S0 XXXX
- PRI ECMA-QSIG slave (1cr/2cr)
-PRI ECMA-QSIG master

I tried nearly with all of them.

1/With AmtPP with CRC4:

+++zaptel.conf
span = 1,0,0,ccs,hdb3 (we have to be master)
bchan=1-15,17-31
dchan=16

+++zapata.conf
switchtype=euroisdn
signalling=pri_net
channels=1-15,17-31


calls from Hipath-> Asterisk arrived, but I heard nothing. Log is below:
-----------------BEGIN
LOG-----------------------------------------------------------------
< Protocol Discriminator: Q.931 (8)  len=33
< Call Ref: len= 2 (reference 1/0x1) (Originator)
< Message type: SETUP (5)
< [04 03 80 90 a3]
< Bearer Capability (len= 5) [ Ext: 1  Q.931 Std: 0  Info transfer
capability: Speech (0)
<                              Ext: 1  Trans mode/rate: 64kbps, circuit-mode
(16)
<                              Ext: 1  User information layer 1: A-Law (35)
< [18 03 a1 83 9f]
< Channel ID (len= 5) [ Ext: 1  IntID: Implicit, PRI Spare: 0, Preferred
Dchan: 0
<                        ChanSel: Reserved
<                       Ext: 1  Coding: 0   Number Specified   Channel Type:
3
<                       Ext: 1  Channel: 31 ]
< [6c 05 01 80 31 31 33]
< Calling Number (len= 7) [ Ext: 0  TON: Unknown Number Type (0)  NPI:
ISDN/Telephony Numbering Plan (E.164/E.163) (1)
<                           Presentation: Presentation permitted, user
number not screened (0) '113' ]
< [70 05 81 37 31 30 30]
< Called Number (len= 7) [ Ext: 1  TON: Unknown Number Type (0)  NPI:
ISDN/Telephony Numbering Plan (E.164/E.163) (1) '7100' ]
< [7d 02 91 81]
< IE: High-layer Compatibility (len = 4)
-- Making new call for cr 1
-- Processing Q.931 Call Setup
-- Processing IE 4 (cs0, Bearer Capability)
-- Processing IE 24 (cs0, Channel Identification)
-- Processing IE 108 (cs0, Calling Party Number)
-- Processing IE 112 (cs0, Called Party Number)
-- Processing IE 125 (cs0, High-layer Compatibility)
> Protocol Discriminator: Q.931 (8)  len=11
> Call Ref: len= 2 (reference 1/0x1) (Terminator)
> Message type: CALL PROCEEDING (2)
> [18 04 e9 81 83 9f]
> Channel ID (len= 6) [ Ext: 1  IntID: Explicit, PRI Spare: 0, Exclusive
Dchan: 0
>                        ChanSel: Reserved
>                       Ext: 1  DS1 Identifier: 1
>                       Ext: 1  Coding: 0   Number Specified   Channel Type:
3
>                       Ext: 1  Channel: 31 ]
    -- Accepting call from '113' to '7100' on channel 1/31, span
1
    -- Executing Answer("Zap/31-1", "") in new
stack
> Protocol Discriminator: Q.931 (8)  len=15
> Call Ref: len= 2 (reference 1/0x1) (Terminator)
> Message type: CONNECT (7)
> [18 04 e9 81 83 9f]
> Channel ID (len= 6) [ Ext: 1  IntID: Explicit, PRI Spare: 0, Exclusive
Dchan: 0
>                        ChanSel: Reserved
>                       Ext: 1  DS1 Identifier: 1
>                       Ext: 1  Coding: 0   Number Specified   Channel Type:
3
>                       Ext: 1  Channel: 31 ]
> [1e 02 81 82]
> Progress Indicator (len= 4) [ Ext: 1  Coding: CCITT (ITU) standard (0) 0:
0   Location: Private network serving the local user (1)
>                               Ext: 1  Progress Description: Called
equipment is non-ISDN. (2) ]
    -- Executing Wait("Zap/31-1", "1") in new stack
< Protocol Discriminator: Q.931 (8)  len=13
< Call Ref: len= 2 (reference 1/0x1) (Originator)
< Message type: STATUS (125)
< [08 03 81 e4 18]
< Cause (len= 5) [ Ext: 1  Coding: CCITT (ITU) standard (0) 0: 0   Location:
Private network serving the local user (1)
<                  Ext: 1  Cause: Unknown (100), class = Protocol Error (6)
]
<              Cause data 1: 18 (24)
< [14 01 01]
< Call State (len= 3) [ Ext: 0  Coding: CCITT (ITU) standard (0) Call state:
Call Initiated (1)
-- Processing IE 8 (cs0, Cause)
-- Processing IE 20 (cs0, Call State)
< Protocol Discriminator: Q.931 (8)  len=13
< Call Ref: len= 2 (reference 1/0x1) (Originator)
< Message type: STATUS (125)
< [08 03 81 e2 07]
< Cause (len= 5) [ Ext: 1  Coding: CCITT (ITU) standard (0) 0: 0   Location:
Private network serving the local user (1)
<                  Ext: 1  Cause: Wrong message (98), class = Protocol Error
(6) ]
<              Cause data 1: 07 (7)
< [14 01 01]
< Call State (len= 3) [ Ext: 0  Coding: CCITT (ITU) standard (0) Call state:
Call Initiated (1)
-- Processing IE 8 (cs0, Cause)
-- Processing IE 20 (cs0, Call State)
    -- Executing Echo("Zap/31-1", "") in new stack
< Protocol Discriminator: Q.931 (8)  len=33
< Call Ref: len= 2 (reference 1/0x1) (Originator)
< Message type: SETUP (5)
< [04 03 80 90 a3]
< Bearer Capability (len= 5) [ Ext: 1  Q.931 Std: 0  Info transfer
capability: Speech (0)
<                              Ext: 1  Trans mode/rate: 64kbps, circuit-mode
(16)
<                              Ext: 1  User information layer 1: A-Law (35)
< [18 03 a1 83 9f]
< Channel ID (len= 5) [ Ext: 1  IntID: Implicit, PRI Spare: 0, Preferred
Dchan: 0
<                        ChanSel: Reserved
<                       Ext: 1  Coding: 0   Number Specified   Channel Type:
3
<                       Ext: 1  Channel: 31 ]
< [6c 05 01 80 31 31 33]
< Calling Number (len= 7) [ Ext: 0  TON: Unknown Number Type (0)  NPI:
ISDN/Telephony Numbering Plan ( E.164/E.163) (1)
<                           Presentation: Presentation permitted, user
number not screened (0) '113' ]
< [70 05 81 37 31 30 30]
< Called Number (len= 7) [ Ext: 1  TON: Unknown Number Type (0)  NPI:
ISDN/Telephony Numbering Plan ( E.164/E.163) (1) '7100' ]
< [7d 02 91 81]
< IE: High-layer Compatibility (len = 4)
-- Processing Q.931 Call Setup
-- Processing IE 4 (cs0, Bearer Capability)
-- Processing IE 24 (cs0, Channel Identification)
-- Processing IE 108 (cs0, Calling Party Number)
-- Processing IE 112 (cs0, Called Party Number)
-- Processing IE 125 (cs0, High-layer Compatibility)
< Protocol Discriminator: Q.931 (8)  len=33
< Call Ref: len= 2 (reference 1/0x1) (Originator)
< Message type: SETUP (5)
< [04 03 80 90 a3]
< Bearer Capability (len= 5) [ Ext: 1  Q.931 Std: 0  Info transfer
capability: Speech (0)
<                              Ext: 1  Trans mode/rate: 64kbps, circuit-mode
(16)
<                              Ext: 1  User information layer 1: A-Law (35)
< [18 03 a1 83 9f]
< Channel ID (len= 5) [ Ext: 1  IntID: Implicit, PRI Spare: 0, Preferred
Dchan: 0
<                        ChanSel: Reserved
<                       Ext: 1  Coding: 0   Number Specified   Channel Type:
3
<                       Ext: 1  Channel: 31 ]
< [6c 05 01 80 31 31 33]
< Calling Number (len= 7) [ Ext: 0  TON: Unknown Number Type (0)  NPI:
ISDN/Telephony Numbering Plan ( E.164/E.163) (1)
<                           Presentation: Presentation permitted, user
number not screened (0) '113' ]
< [70 05 81 37 31 30 30]
< Called Number (len= 7) [ Ext: 1  TON: Unknown Number Type (0)  NPI:
ISDN/Telephony Numbering Plan ( E.164/E.163) (1) '7100' ]
< [7d 02 91 81]
< IE: High-layer Compatibility (len = 4)
-- Processing Q.931 Call Setup
-- Processing IE 4 (cs0, Bearer Capability)
-- Processing IE 24 (cs0, Channel Identification)
-- Processing IE 108 (cs0, Calling Party Number)
-- Processing IE 112 (cs0, Called Party Number)
-- Processing IE 125 (cs0, High-layer Compatibility)
< Protocol Discriminator: Q.931 (8)  len=33
< Call Ref: len= 2 (reference 1/0x1) (Originator)
< Message type: SETUP (5)
< [04 03 80 90 a3]
< Bearer Capability (len= 5) [ Ext: 1  Q.931 Std: 0  Info transfer
capability: Speech (0)
<                              Ext: 1  Trans mode/rate: 64kbps, circuit-mode
(16)
<                              Ext: 1  User information layer 1: A-Law (35)
< [18 03 a1 83 9f]
< Channel ID (len= 5) [ Ext: 1  IntID: Implicit, PRI Spare: 0, Preferred
Dchan: 0
<                        ChanSel: Reserved
<                       Ext: 1  Coding: 0   Number Specified   Channel Type:
3
<                       Ext: 1  Channel: 31 ]
< [6c 05 01 80 31 31 33]
< Calling Number (len= 7) [ Ext: 0  TON: Unknown Number Type (0)  NPI:
ISDN/Telephony Numbering Plan ( E.164/E.163) (1)
<                           Presentation: Presentation permitted, user
number not screened (0) '113' ]
< [70 05 81 37 31 30 30]
< Called Number (len= 7) [ Ext: 1  TON: Unknown Number Type (0)  NPI:
ISDN/Telephony Numbering Plan ( E.164/E.163) (1) '7100' ]
< [7d 02 91 81]
< IE: High-layer Compatibility (len = 4)
-- Processing Q.931 Call Setup
-- Processing IE 4 (cs0, Bearer Capability)
-- Processing IE 24 (cs0, Channel Identification)
-- Processing IE 108 (cs0, Calling Party Number)
-- Processing IE 112 (cs0, Called Party Number)
-- Processing IE 125 (cs0, High-layer Compatibility)
< Protocol Discriminator: Q.931 (8)  len=33
< Call Ref: len= 2 (reference 1/0x1) (Originator)
< Message type: SETUP (5)
< [04 03 80 90 a3]
< Bearer Capability (len= 5) [ Ext: 1  Q.931 Std: 0  Info transfer
capability: Speech (0)
<                              Ext: 1  Trans mode/rate: 64kbps, circuit-mode
(16)
<                              Ext: 1  User information layer 1: A-Law (35)
< [18 03 a1 83 9f]
< Channel ID (len= 5) [ Ext: 1  IntID: Implicit, PRI Spare: 0, Preferred
Dchan: 0
<                        ChanSel: Reserved
<                       Ext: 1  Coding: 0   Number Specified   Channel Type:
3
<                       Ext: 1  Channel: 31 ]
< [6c 05 01 80 31 31 33]
< Calling Number (len= 7) [ Ext: 0  TON: Unknown Number Type (0)  NPI:
ISDN/Telephony Numbering Plan ( E.164/E.163) (1)
<                           Presentation: Presentation permitted, user
number not screened (0) '113' ]
< [70 05 81 37 31 30 30]
< Called Number (len= 7) [ Ext: 1  TON: Unknown Number Type (0)  NPI:
ISDN/Telephony Numbering Plan ( E.164/E.163) (1) '7100' ]
< [7d 02 91 81]
< IE: High-layer Compatibility (len = 4)
-- Processing Q.931 Call Setup
-- Processing IE 4 (cs0, Bearer Capability)
-- Processing IE 24 (cs0, Channel Identification)
-- Processing IE 108 (cs0, Calling Party Number)
-- Processing IE 112 (cs0, Called Party Number)
-- Processing IE 125 (cs0, High-layer Compatibility)
< Protocol Discriminator: Q.931 (8)  len=9
< Call Ref: len= 2 (reference 1/0x1) (Originator)
< Message type: DISCONNECT (69)
< [08 02 80 90]
< Cause (len= 4) [ Ext: 1  Coding: CCITT (ITU) standard (0) 0: 0   Location:
User (0)
<                  Ext: 1  Cause: Unknown (16), class = Normal Event (1) ]
-- Processing IE 8 (cs0, Cause)
    -- Channel 0/31, span 1 got hangup request
  == Spawn extension (incoming, 7100, 3) exited non-zero on 'Zap/31-1'
NEW_HANGUP DEBUG: Calling q931_hangup, ourstate Disconnect Indication,
peerstate Disconnect Request
> Protocol Discriminator: Q.931 (8)  len=9
> Call Ref: len= 2 (reference 1/0x1) (Terminator)
> Message type: RELEASE (77)
> [08 02 81 90]
> Cause (len= 4) [ Ext: 1  Coding: CCITT (ITU) standard (0) 0: 0   Location:
Private network serving the local user (1)
>                  Ext: 1  Cause: Unknown (16), class = Normal Event (1) ]
    -- Hungup 'Zap/31-1'
< Protocol Discriminator: Q.931 (8)  len=5
< Call Ref: len= 2 (reference 1/0x1) (Originator)
< Message type: RELEASE COMPLETE (90)
NEW_HANGUP DEBUG: Calling q931_hangup, ourstate Null, peerstate Null
NEW_HANGUP DEBUG: Destroying the call, ourstate Null, peerstate Null
----------------------------END
LOG------------------------------------------------------------

I have dupechecked to see that both side use A-Law. Strange. What's can be
the reason for this? I dunno.

Calling from Asterisk to Hipath have worse fate. Call terminate immediately
with:

----------------BEGIN LOG --------------------------
 -- Accepting AUTHENTICATED call from 203.162.39.167:
       > requested format = gsm,
       > requested prefs = (),
       > actual format = gsm,
       > host prefs = (gsm|ilbc),
       > priority = mine
    -- Executing SetCallerID("IAX2/2209-2", "8223113") in
new stack
    -- Executing Dial("IAX2/2209-2", "ZAP/1/8223113|40|r")
in new stack
-- Making new call for cr 32773
    -- Requested transfer capability: 0x00 - SPEECH
> Protocol Discriminator: Q.931 (8)  len=38
> Call Ref: len= 2 (reference 5/0x5) (Originator)
> Message type: SETUP (5)
> [04 03 80 90 a3]
> Bearer Capability (len= 5) [ Ext: 1  Q.931 Std: 0  Info transfer
capability: Speech (0)
>                              Ext: 1  Trans mode/rate: 64kbps, circuit-mode
(16)
>                              Ext: 1  User information layer 1: A-Law (35)
> [18 04 e1 81 83 81]
> Channel ID (len= 6) [ Ext: 1  IntID: Explicit, PRI Spare: 0, Preferred
Dchan: 0
>                        ChanSel: Reserved
>                       Ext: 1  DS1 Identifier: 1
>                       Ext: 1  Coding: 0   Number Specified   Channel Type:
3
>                       Ext: 1  Channel: 1 ]
> [6c 09 41 81 38 32 32 33 31 31 33]
> Calling Number (len=11) [ Ext: 0  TON: Subscriber Number (4)  NPI:
ISDN/Telephony Numbering Plan ( E.164/E.163) (1)
>                           Presentation: Presentation permitted, user
number passed network screening (1) '8223113' ]
> [70 08 c1 38 32 32 33 31 31 33]
> Called Number (len=10) [ Ext: 1  TON: Subscriber Number (4)  NPI:
ISDN/Telephony Numbering Plan ( E.164/E.163) (1) '8223113'
]
> [a1]
> Sending Complete (len= 1)
    -- Called 1/8223113
< Protocol Discriminator: Q.931 (8)  len=10
< Call Ref: len= 2 (reference 5/0x5) (Terminator)
< Message type: RELEASE COMPLETE (90)
< [08 03 85 e4 18]
< Cause (len= 5) [ Ext: 1  Coding: CCITT (ITU) standard (0) 0: 0   Location:
Private network serving the remote user (5)
<                  Ext: 1  Cause: Unknown (100), class = Protocol Error (6)
]
<              Cause data 1: 18 (24)
-- Processing IE 8 (cs0, Cause)
    -- Channel 1/1, span 1 got hangup
NEW_HANGUP DEBUG: Calling q931_hangup, ourstate Null, peerstate Null
NEW_HANGUP DEBUG: Destroying the call, ourstate Null, peerstate Null
    -- Hungup 'Zap/1-1'
  == Everyone is busy/congested at this time (1:0/0/1)
  == Auto fallthrough, channel 'IAX2/2209-2' status is
'CHANUNAVAIL'
--------------- END LOG------------------------------

Well, changing the Hipath side to  ECMA-QSIG slave and Asterisk side to
switchtype=qsig have same effect. Call from HP3750 arrived to Asterisk, but
nothing heard. And from Asterisk to HP3750, call was terminated with the
same reason.


Since you and others has successfully setup Siemens and Asterisk. I have
strong believe that I was wrong on protocol selection on both sides
(Asterisk and HP). Can you help to point out, what protocol I should set on
HP3750 and Asterisk?

Sorry List for long posting.
Thanks and best regards,
Nguyen



-- 
With best regards,
Nguyen
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
http://lists.digium.com/pipermail/asterisk-users/attachments/20060620/8a434429/attachment.htm