similar to: CAPI channel not available but nobody is using the system

Armin, I am running 1.2.7.1 with an Eicon T1 board version 2 on Debian 2.4 I don't know the details on chan-capi / CAPI drivers. We did the install April of this year. How can I tell what I have? Thank you for your time. Tim -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com]On Behalf Of Armin Schindler Sent: Wednesday,

I've the following setup : sip phone -> ser (auth and routing) -> asterisk with capi isdn when I call a pstn number everything works fine, but I can't hear anything till the called answer. this is the output from a test call : -- Executing Playtones("SIP/2.7.184.61-08152880", "dial") in new stack -- Executing Dial("SIP/2.7.184.61-08152880",

Hi, I?ve strange problem when I?m making a call from SIP (Cisco 7960) to capi (Fritz PCI). When I call a national number, I?m hearing the ringtone when the called party is ringing but when I call an international number, I don?t hear the ringtone and I?ve a silence until the called party answers. Both call are going through the same extension. Here?s 2 log files, one with a national number and

Hello, I have som problems with my BRI/capi setup. I manage to call in to the system (some rows below). ---------------- -- Executing Dial("CAPI[contr1/16453]", "SIP/BYEXTENSION@janm|10") in new stack -- Called s@janm -- SIP/janm-63f5 is ringing -- SIP/janm-63f5 is ringing -- SIP/janm-63f5 is ringing ---------------- But I can't make outgoing calls from

Hello all, I'm trying to get CAPI to work with two B channels (AVM B1 PCMCIA) on a P4 2GHz (linux kernel 2.4.21) system. All are ok with just one B channel. But when I open a second B chan, the sound is choppy, with too long gaps, and the CPU load is too high (~50%). On the Asterisk's console I get these messages: -- Executing Dial("H323:4478",

hi all, i have a probably very stupid question/problem. for testing purpose i am trying to get asterisk running with two isdn cards. I'd only like to here the demo sound when i call the number - but nothing works. The output of show channels is not showing any channel - should there be 4 channels ? - capi info shows my two cards perfectly. The ISDN Controller's are attached to an PTMP

Hello Armin, > The card is telling: > > CAPI INFO 0x34a2: No circuit / channel available > > so the other channel must be in use by something else. > Maybe another device on the ISDN line? > I have tested it several times now and always entered "capi info" before and after the call. The answer was always: Contr1: 2 B channels total, 2 B channels free. I'm

Hello All, I am having an odd problem with Armin's chan-capi_cm on builds higher than 7955. It would seem that this happens on anything higher than 7955. What is happening is the isdn is ringing, then asterisk does a goto-if and just hangs. Asterisk itself is ok, but the isdn then rings out or busys out on the other side. Outgoing works fine, this only seems to effect incoming. I

Dear asterisk users! I want to control a hardware pbx with asterisk. What I need to do this is being able to press "hold" which can be done with capicommand(hold) and then send digits on a bri card which connects to my asterisk computer. So far I use Dial(CAPI/ISDN1/27:<<digits>>/bo,15) to do this. Are there better ways? Note that these are not dtmf, I'm afraid. I use

anyone has idea what problem can be here, something with codec but i have today CVS version and grandstream phone with 1.5.0 firmware.I try to change codec in phone and also in asterisk-sip.conf but the same. What can be problem ? tnx, Tomaz *CLI> -- Executing Dial("SIP/102-767c", "CAPI/2:5") in new stack -- Called 2:5 -- CAPI[contr1/2003002]/0 is making

Hi, I'm new to asterisk and try to get it work with capi.so. When I try to start asterisk with "asterisk -vvvvc" I get the following errors. I couldn't find any hint on the net what may be wrong in my configs. Has anybody got a hint? Here is the error output: [capi.so] => (Common ISDN API for Asterisk) == Parsing '/etc/asterisk/capi.conf': Found Jun 23

Hi, I have installed the above two, and have two questions: * Is there a reason (or better=a fix), why the chan-capi-1.0.0 does not compile together with Asterisk 1.4.2? * Anyone else experiencing problems with chan-capi-HEAD not seeing the controller? If I run asterisk with verbose setting to 0, i.e. just asterisk -c chan-capi does not find the controller. Starting asterisk with verbosity

Hi I've got a dell 2550 with an Eicon Diva server PRI card plugged into it. I can call out using the acopy2 test utility. I'm having trouble with asterisk making calls however... my capi.conf and modules.conf looks correct by the wiki instructions - does anyone have any advice on where to look ? I can attach conf files etc. if needed. Asterisk says it has 30 capi channels available,

Hello, I am trying to configure asterisk 1.0.7pre to get incoming calls from an ISDN line using an AVM fritz PCI 2.0 with Chan_capi 0.3.5. My problem is that the context is not recognised in the /etc/asterisk/capi.conf I have in /etc/asterisk/capi.conf 's section "[interfaces]" the following directive context=isdn and the following directive in /etc/asterisk/extensions.conf in

Hi all, * was running ... I have a WT405P and an AVM C4 with chan_capi 0.3.4a Today chan_capi stopped working, without any changings at the system. It seems, that not * is the reason, because isdn-log also shows no calls. If I try to call * from outside via capi, I only get a busy. That is the try from inside to outside: stern01*CLI> -- data = @89930:0107901723168212 -- capi

Hi, I am having trouble configuring CAPI so that call transfers work. I make a SIP call to asterisk which goes out on ISDn via CAPI. Then I try to do a transfer from the SIP phone which doesn't work and results in the call being disconnected. The error message given by asterisk is that it chan_capi can't find an entry for the outgoing msn for the transfer however the outgoing msn is the

Hello list! I have a Asterisk 1.2.10 running using the package from Backports.org for Debian Sarge. I have setup chan_capi (0.6.5 from Backports) and it seems that I am only able to use on B-Channel. When trying to place the second call I get: CAPI INFO 0x34a2: No circuit / channel available capi info shows: Contr1: 2 B channels total, 1 B channels free And capi.conf is: [ISDN1]

Hallo all, I am trying to get * with chan_capi and a ptp-ISDN with 4 lines on a AVM C4 card to work. But weather inbound nor outbound is working :( My capi.conf: ; ; CAPI config ; ; [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] mode=immediate isdnmode=ptp msn=8993 incomingmsn=* mode=immediate controller=1,2,3,4 softdtmf=1 ;accountcode= context=demo

O.K. thanks a lot, Felix and Peer Oliver. But somehow asterisk keeps telling me while startup: [chan_capi.so] => (Common ISDN API for Asterisk) Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr1 Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr2 Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr3 Jan 24 14:30:47

hi, I've been running a pure sip asterisk box for a while now with no problems, and i've recently added an isdn2e line from bt in the uk. everything is hooked up and i've got it ringing my sip extensions, but the logs don't quite look perfect and i can't see any description of what i should consider to be normal behaviour. would someone be able to look this over and tell me