similar to: Switchtype,Signalling,rxwink warnings

hi all iam using ztdummy driver after my call end , when i look at debug mode in cli i get this errors --- (0 headers 0 lines) Nat keepalive --- -- Reloading module 'chan_agent.so' (Agent Proxy Channel) == Parsing '/etc/asterisk/agents.conf': Found -- Reloading module 'chan_local.so' (Local Proxy Channel) -- Reloading module 'chan_zap.so' (Zapata

Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]:

I'm not sure if I have a configuration problem or not. I am unable to dial out. When I try to dial in I can hear the phone ring on the dialling phone but Asterisk does not register anything. In zaptel.conf I have loadzone = au defaultzone=au fxsks=1 In zapata.conf language=au context=from-pstn When I do: zap show channels I get: Chan Extension Context Language

Hello all I just checked out the latest zaptel/zapata/libpri/asterisk/asterisk-addons from the cvs and ran through the entire make procedures. Everything seemed to go fine however now when I attempt to start asterisk, it says ok but it seems to be immediately crashing. The following messages are displayed in my /var/log/asterisk/messages file for the time right around the crash: Dec 29

When dtmfmode is set to inband for SIP, and i originate a call from sip out to the PSTN, I can hear the DTMF digit twice in the audio stream. Once very briefly and once for normal duration. Our Theory: While Asterisk is parsing the DTMF, for a fraction of a second, while the end user generated DTMF is being detected, the DTMF is passed inband. Once the DTMF is detected Asterisk silences it

I reloaded my asterisk and found some red lines flushing by. When I stopped it I see: WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring signalling WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring echocancelwhenbridge WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring echotraining Reconfigure channel 1, FXO Kewlstart signalling Reconfigure channel 2, FXO Kewlstart signalling

hi after some testing with A@H, i've decided to install my asterisk server on a slackware (because it's my favourite distro and it is still suggested here http://www.voip-info.org/wiki-Asterisk+Linux+Slackware) , so, i've installed the last 10.2 release, and i've recompiled the 2.6.15.4 kernel. then i've downloaded asterisk1.2.4 and zaptel1.2.4 i load module zaptel and

Hi, Is there a way I can stop logging this specific messages: Dec 18 13:24:52 ERROR[6913] chan_sip.c: Call to user 'remi' rejected due to usage limit of 1 Without having to completely stop logging all error messages in my log files. Thanks, Remi

Hi, I have a Asterisk that connects to the PSTN via a PRI. After Asterisk sends the setup message it immediately sends a 183 Session Progress. Is there a way I can change it so that it sends a 100 Trying instead? Because I am having some issues with a equipment where it does not play a busy tone as a result of sending a 183 Session Progress then the 486 Busy. Thanks Remi

Hi Since Im using the mISDN drivers and no zaptel stuff, I had to install ztdummy to get MeetMe to work. Well, that was the plan. Now, after getting the latest zaptel version over CVS (Im using Kernel 2.6), uncommenting all the modules except ztdummy in zaptel.sysconfig file and compiling this by "make", "make install" and "make linux26", I rebooted and

Hello guys! I hope you bare with yet another newbie on the list! :-) I am trying to setup an asterisk installation in between a Siemens HiPath 3800 and my local carrier (Telefonica/Brazil). Both running R2. ISDN is not an option on the carrier. :-( I could apparently setup both E1s just fine according to zttool (both OK with no alarms) but, and this is where it starts to get

(Sorry of this appears in the list twice, but I wasn't sure if it was blocked or not) Hi there, I'm having a problem with my TDM-400P which has been working like a charm up until very recently. It started to fail last week, and so I was hoping someone could illuminate me with some information as to why. Its configuration is as follows: ------------ FXS (green) module is in position 1,

Anyone have any idea what this is talking about. Here is my zapata.conf [channels] switchtype=5ess signalling=pri_cpe echocancel=yes echocancelwhenbridged=yes echotraining=400 callerid=asreceived group=1 context=default musiconhold=default faxdetect=incoming channel => 1-23 Here is my zaptel.conf span=1,1,0,esf,b8zs bchan=1-23 # set this to 1-15,17-31 for E1 dchan=24 # set this to 16 for

When I reload the config, I see this error in the CLI. However, I don't see what I have done wrong: == Parsing '/etc/asterisk/zapata.conf': Found May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring signalling -- Reconfigured channel 1, FXO Kewlstart signalling May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring signalling -- Reconfigured

Hi, Has anyone ever had any problem with the TE220B card with it showing up as four ports instead of two. I RMA'd the first one with the retailer (Digium tech advice), but I just got another brand new card and it is coming up as four ports again. The card identifier is showing 0420 when I do lspci. Has this happened to anyone and if so is there a fix? Remi

Good day all We got a Wildcard TE110P I installed linux,zaptel,libpti and asterisk I coped over my zaptel.conf and zapata.conf from a previous E100P config But when I try to start asterisk it gives error not bying able to load zap channles: == Parsing '/etc/asterisk/zapata.conf': Found Jan 10 08:17:18 WARNING[-1084595552]: chan_zap.c:9308 setup_zap: Ignoring switchtype Jan 10 08:17:18

Hi all, I have a problem with the cvs head zaptel library: I cannot update my zapata.conf into asterisk when I issue the reload command from the CLI prompt; only when I stop and restart the asterisk service. The system sends the following message: Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364 setup_zap: Ignoring switchtype Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364

Hiya all, I have had no end of trouble trying to get my A101 E1 card working on a new asterisk installation. The sangoma tech people have ignored my emails about this. All the installation of wanpipe seems to go ok, and zaptel. it all installed compiled and does all the wanpipe hwprobe exactly as documented. Asterisk compiled ok, but when I run it give me Jun 27 11:12:18 ERROR[10528]:

Hi, I'm getting crazy about ztdummy. I have to replicate a PBX where ztdummy is working fine but for some reason I cannot. The two machines have the same kernel, motherboard, the same gcc version and the same zaptel 1.4.8. On the second machine zaptel compiles without errors and ztdummy.ko is generated but when I modprobe it I get the following error in messages: rtc: lost some interrupts

Hi, Could anyone tell me how to read the values in the "zonedata.c" file? I am looking at the "zt_tone_ringtone" field mainly. Thank you. Jad Wauthier -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070512/4c0387be/attachment.htm