similar to: siemens pbx and asterisk

Hello all. I have installed and functioning asterisk-1.2.9.1 where I effected one upgrade in asterisk-1.0.9, is interconnected with a PABX Siemens HiPath 4000 in ISDN PRI with protocol QSIG, the one that is happening he is that the calls originated for PABX Siemens and destined to SIP phones asterisk are being without audio, nor Ring, is dumb. They could help in this case me? Best Regards Josu?

Hi * :-) I found in the online WiKi docs some information on how to integrate Asterisk with "old PBX"... http://www.voip-info.org/wiki-Asterisk+legacy+integration ...but I couldn't find anything on integration with a Siemens HiCom 150E. Later on we'll migrate to a HiPath 3750 so information covering this model would be nice too... Do you know if any of the PBX listed

Hello all. I have installed and functioning asterisk-1.2.9.1 where I effected one upgrade in asterisk-1.0.9, is interconnected with a PABX Siemens HiPath 4000 in ISDN PRI with protocol QSIG, the one that is happening he is that the calls originated for PABX Siemens and destined to SIP phones asterisk are being without audio, nor Ring, is dumb. They could help in this case me? Best Regards Josu?

Hi all, I'm trying to setup Asterisk trunk to Siemens HiPath 4000 V2.01 What would be the best way to do so? I am a bit confused because as far as I've understand this PBX doesn't support H323, but I saw somewhere someone who created a cornet trunk and it worked using H323. So if anyone knows what I need to configure I would appreciate it. I've read some information

Hello! Is it possible to connect Siemens HiPath 4000 to Asterisk? What equipment required on Siemens side? I mean IP not E1. Sorry for asking here. Siemens-related websites use "salesperson language". There is no technical information.

Hi all, I'm confused, in digium website, it says: TDM2400P: It supports a combination of up to 6 FXS and/or FXO modules for a total of 24 lines. 6 plus 6 is 12, how come it's 24? if I have 24 PSTN lines, i'll be needing 24 FXOs. Pls. elaborate. thanks. Lito -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi Stephen, You said that PRI works great. We are using HiPath 3550 and Siemens digital phone which using *11, *97 etc for function keys. However Asterisk uses the the * key plus one or two digits for function keys as well(it is common key combination for functions). So is it any way to disable *11, *97 keys in HiPath system and pass this keys to Asterisk? Thanks and regards, Isaac >Hi

For all who are interested: A quick review of CeBIT 2005. :-) CeBIT was a very successfull event. Most of the time, the asterisk-booth was crowded with more people than we could talk to. We had with us a demo-installation including different IP-phones, digital and analog phones as well as a Siemens HiPATH PBX to which our Asterisk-server served as a VoIP-gateway, and many people were impressed

Hi, I am looking to integrate Asterisk with a Siemens HiCom 150e via BRI and wondered if anyone is able to offer any advice. In simplistic terms, my goal is to pass calls from the HiCom to the Asterisk box. e.g: HiCom user dials access code and can call Asterisk extension or establish SIP call over Internet. Likewise, I'd like Asterisk to be able to present a call to the Hicom, either

This might be a newbie question but I'm just wondering how would it be possible to have 30 analog lines using asterisk for PBX by just using TDM40B and X100P (or are there any device>), if an ordinary PC support just 4 PCI slots? the maximum scale i guess would just be 2 x 8. Adding a new PC just for this purpose would be costly. I would appreciate your comments. Thanks.

I am connecting to a siemens hipath 4000 with dahdi 2.1.0.4 and asterisk 1.4.23 using a Te210P card. the phone guy is saying that the lines are reporting always BUSY. however on my end the status shows OK. Anyone seen this? Is there something different about connecting PRI to siemens hipath? system.conf shows: loadzone=us defaultzone=us span=1,1,6,esf,b8zs bchan=1-5 dchan=24

Hello all, I am trying to connect asterisk to a Siemens Hipath 3750 PBX system. I have a physical connection issue. I know that I should use a crossover RJ48 cable to link the two systems. The problem however is that the physical interface of the Siemens system is very unfamiliar. From my digging around, I think that this is an S2M interface. http://www.mail-archive.com/asterisk-users at

Hello all, is it possible to define a pilot number in asterisk, say I have 3 direct lines and I want one of those direct lines to be used as pilot number? When that number is contacted it will be redirected to the available zap and original zap that receive it will be freed to receive another call. It can only be used when all 2 lines ares used. Thanks. Lito -------------- next part

> Lito Lampitoc wrote: > > thanks for enlightening. So you mean, if I have 3 lines when the > caller > > dialled the first line and it was busy, the call will be diverted > to the > > next two available lines in random? > > > > I don't think it's random. I think its just sequential. If main > line > is busy, try second. If that is

Hi all, I have a connect between a siemens hipath & Asterisk system over PRI The connection works perfectly I can call from the Hipath to an Asterisk Extension. I want to allow the hipath extensions to dial out over a SIP trunk on asterisk but I keep getting "The number you have dialed is not in service" In this CLI I'm dialing from hipath extension 9 (prefix for sip trunk)

Hello, if somebody using this scenario in production successfully, please send me info, which ISDN card for asterisk server is usefull for me (Digium, Sangoma)? my crucial requirement is "caller id name" transfer/display between ISDN (Siemens PBX) and IP phone connected to asterisk I'm using PRI interface and Q.SIG signaling. thank you PJ

Hi I've bought the Wildcard TE110 some days ago but I'm unable to get it to work with Siemens HiCom 300. I've tried this so far: 1. I've used standard cat5 cable cut off on one edge and twisted wires 1 to 4 and 2 to 3 which is according to cisco a short circuit for E1 lines. Wildcard takes a few seconds and sets the link to green (OK). 2. I've tried to connect our running

hi all, we do have some troubles with zaptel timing source - we have a setup with 3 telco PRI lines, connected to asterisk digium card 0 - asterisk does some handling - calls are leaving on digium card 1 - going to a siemens hipath - there is some call handling - some of the calls then are going from the hipath over a qsig line to a bosch integral PBX - handling the rest of the calls. To be able

I downloaded asterisk to use cvs to checkout the release version. After installing, I would like to load module chan_h323.so but there is some error : *CLI> load chan_h323.so Feb 17 15:22:38 WARNING[2865]: loader.c:258 ast_load_resource: /usr/lib/asterisk/m odules/chan_h323.so: undefined symbol: __use_ast_pthread_create_instead__ Unable to load module chan_h323.so *CLI> How can I solve

> > Great service. Hope it catches on. > > > > In time there will probably have to be some adjustments: > > > > - ratio 10/1 - this means everyone can make 10 calls for every call > donated. > > This doesn't add up in the long run. > > - I get credited 10 calls for every call I make to my own dialplan. This > > should be fixed. > > -