Simon D
2005-Sep-13 06:14 UTC
[Asterisk-Users] Integration between Asterisk and Siemens HiCom 150e over ISDN
Hi, I am looking to integrate Asterisk with a Siemens HiCom 150e via BRI and wondered if anyone is able to offer any advice. In simplistic terms, my goal is to pass calls from the HiCom to the Asterisk box. e.g: HiCom user dials access code and can call Asterisk extension or establish SIP call over Internet. Likewise, I'd like Asterisk to be able to present a call to the Hicom, either Asterisk extension calling HiCom extension, or an incoming Sipgate call presented to the HiCom, for example. My hardware: - Asterisk: I have an Asterisk box configured with 1x Sitecom DC105 PCI ISDN Card (HFC chipset, TE/NT capable). [and 2x X100P Analogue FXOs, but that's not relevant here] My understanding is that I should configure the ISDN card in NT mode and power the bus with an NT1, or will a crossover cable in to the HiCom suffice? Reference to NT1's and line power here: http://isdn.jolly.de/download/v3.0/PBX4Linux-3.0.pdf - Siemens HiCom 150e: I currently have a HiCom 150e switch with digital and analogue stations and an analogue trunk card (TLA4). I also have an STLS4 card. Initially, I thought this would be the answer to my prayers but now am not so sure... According to http://www.webco.com/siemens/interfaces.html, my STLS4 is defined as the following: "Connects up to 4 ISDN S0 terminals (8 channels) for data equipment and video conferencing applications to the OfficePoint or OfficeCom. Connected devices must provide their own power. Some special wiring for the ISDN S0 device connection is required. Also requires connection of ISDN BRI trunks (TMQ4) for network access." Documentation on ISDN BRI: http://web2.tac.siemenscom.com/pub/150e/Config/Note020.pdf Documentation on ISDN S0 Device Install: http://web2.tac.siemenscom.com/pub/150e/Config/Note009.pdf I can't figure out if the SLTS4 is the correct card for my requirements, or do I need a TMQ4 *as well* or a TMQ4 *instead*?.. Trawling through previous posts, I've found reference to the STLS4 here: http://lists.digium.com/pipermail/asterisk-users/2005-January/081449.html Is anyone able to help? Many thanks in advance, Simon England, UK
Sander
2005-Sep-13 08:04 UTC
[Asterisk-Users] Integration between Asterisk and Siemens HiCom150e over ISDN
Just setup the stls4 card to work in NT mode and connect the siemens pbx to the asterisk with a crossover cable. Then you will be able to make calls to from the hicom to the asterisk machine you do not need to have an nt box to make the connection. With the nt box you can power an ISDN phone if the phone needs power. -----Oorspronkelijk bericht----- Van: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Namens Simon D Verzonden: dinsdag 13 september 2005 15:14 Aan: asterisk-users@lists.digium.com Onderwerp: [Asterisk-Users] Integration between Asterisk and Siemens HiCom150e over ISDN Hi, I am looking to integrate Asterisk with a Siemens HiCom 150e via BRI and wondered if anyone is able to offer any advice. In simplistic terms, my goal is to pass calls from the HiCom to the Asterisk box. e.g: HiCom user dials access code and can call Asterisk extension or establish SIP call over Internet. Likewise, I'd like Asterisk to be able to present a call to the Hicom, either Asterisk extension calling HiCom extension, or an incoming Sipgate call presented to the HiCom, for example. My hardware: - Asterisk: I have an Asterisk box configured with 1x Sitecom DC105 PCI ISDN Card (HFC chipset, TE/NT capable). [and 2x X100P Analogue FXOs, but that's not relevant here] My understanding is that I should configure the ISDN card in NT mode and power the bus with an NT1, or will a crossover cable in to the HiCom suffice? Reference to NT1's and line power here: http://isdn.jolly.de/download/v3.0/PBX4Linux-3.0.pdf - Siemens HiCom 150e: I currently have a HiCom 150e switch with digital and analogue stations and an analogue trunk card (TLA4). I also have an STLS4 card. Initially, I thought this would be the answer to my prayers but now am not so sure... According to http://www.webco.com/siemens/interfaces.html, my STLS4 is defined as the following: "Connects up to 4 ISDN S0 terminals (8 channels) for data equipment and video conferencing applications to the OfficePoint or OfficeCom. Connected devices must provide their own power. Some special wiring for the ISDN S0 device connection is required. Also requires connection of ISDN BRI trunks (TMQ4) for network access." Documentation on ISDN BRI: http://web2.tac.siemenscom.com/pub/150e/Config/Note020.pdf Documentation on ISDN S0 Device Install: http://web2.tac.siemenscom.com/pub/150e/Config/Note009.pdf I can't figure out if the SLTS4 is the correct card for my requirements, or do I need a TMQ4 *as well* or a TMQ4 *instead*?.. Trawling through previous posts, I've found reference to the STLS4 here: http://lists.digium.com/pipermail/asterisk-users/2005-January/081449.html Is anyone able to help? Many thanks in advance, Simon England, UK _______________________________________________ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users