similar to: x100p buying advice

Hello, Can the wildcard x100P be bought of the shelf in stores - say in Singapore. Thanks Varun

Anyone know why the knock-off X100p prices have jumped? -Nate

Hi All, Sorry if this has been around a millions times.. I have been off this list for a few months now.. I have installed the latest asterisknow (upgraded asterisk to 1.6 as well) and I am having a hard time getting my X100P and TDM400P working.. Its all new to me with dahdi because my old server is still running Asterisk 1.0.2 so there have been lost of changes.. Can someone point me in

Since the X100P/X101P/Clone cards does not work in all countries that use DTMF based Caller-ID systems, I've developed a hardware that you connect to a serial port and the PSTN. You then run a perl script "cid_logger.pl" as a daemon, and modify extensions.conf to call an agi script whenever a call comes in, and if it's on the X100 card it will get the caller id information

I was told the X100P will have issues if installed on a line with a DSL connection. Is there a card that will work correctly on a DSL connection? Thanks!! -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040504/6de6226b/attachment.htm

Hello I setup Asterisk@Home with purely VoIP and it worked fine. I then added an X100P card so I could call out / take inbound calls via PSTN and that went fine. But I have just added a TDM400P card (specifically a TDM30B) and now problems. Here is some of the output. Any ideas on what I should be looking at next? When I run genzaptelconf -s -d I get lots of erors on screen - bit I can

I just installed two new X100P's today in my RH7.3 box and was poking around /proc What does the RED refer to on board 2? /proc/zaptel/1 Span 1: WCFXO/0 "Wildcard X101P Board 1" 1 WCFXO/0/0 /proc/zaptel/2 Span 2: WCFXO/1 "Wildcard X101P Board 2" RED 2 WCFXO/1/0 Any clues on how to setup channels on the two interfaces?? I am up to here in

Hi all, With a great help from Richard Alexander (thanks Richard!) I have now a functional CallerID on my X100P. This is what I have done: - update to the latest CVS (as today at 5:00pm GMT) - modify the callerid.c file in the asterisk source like that. original : /* MDMF */ /* Go through each element and process */

can somebody that has these hardwares(X101P and S400P) working on his asterisk system please assist.................. you can send the solution to austino@skannet.com..... the error message is what i have below. ---------- Forwarded message ---------- Date: Thu, 1 May 2003 21:01:21 +0100 (WAT) From: austino@skannet.com To: asterisk-user@lists.digium.com Subject: Error working with X101P and

Hi All, When the Caller hangup at the voice menu, the wildcard X100P didn't disconnect the calls properly and it just keep looping at the voice menu and timeout and loop again, are there any methods can fix the problems? Please help! Thanks, Randal

I'm having sporadic problems with my X100P card. When trying trying to call out I get a message on the console that the channel is busy even though I have bounced asterisk. It seems the card grabs the line and doesn't let go. When I try to call the number I get a busy signal. If I perform a rmmod wcfxo and restart asterisk everything retruns to normal. I have a TDP400P installed along with

Wow ! No reply... May be I must talk about X100P instead of X101P ? Is someone has yet encountered this kind of "no sound" problem when bridging two FXO lines like this (first as input, second as output) ? Any idea ? TIA. Best Regards, Francois BERGERET, France. ----- Original Message ----- From: "Francois BERGERET" <f6hqz-m@hamwlan.net> To: "Asterisk Users

Hi Please help! I have one X101P and TDM400P in my asterisk Box When i make a call from * to PSTN, everything goes Ok, When the PSTN hangups or * hangups, the busy tone is detected and * disconnects the channel without problems. The problem occurs when the call comes from PSTN. When * hangups, the other end (at pstn) does not hangup, it only presents silence. Please tell me how to solve this

When x101p clone receive ring signal from phone line, my voip phone start ringing. But, if caller hang-up at some time, phone continues to ringing 10 second more. How can I shorten that time? Pause betwen incoming rings on my phone line is 4s, so when x101p clone (wcfxo driver) do not receive next ring signal after 4.5 sec, call should be consider as ended. What should I change to set that time

I'm looking to acquire another FXS module -- either the TDM400P daughter module or USB S100U is fine. I'll happily buy from Digium, but thought I would give the folks here an opportunity to recycle any extra hardware :-). Please contact me if you have one to sell. Thanks! -- David

Hi, I have a X101P card and am running Asterisk SVN-trunk-r226890. The X101P card seems to be identified properly: debian:/usr/src/dahdi-tools# dahdi_hardware pci:0000:01:01.0 wcfxo+ e159:0001 Wildcard X101P debian:/usr/src/dahdi-tools# dahdi_cfg -vv DAHDI Tools Version - SVN-trunk-r7409 DAHDI Version: SVN-trunk-r7445 Echo Canceller(s): MG2 Configuration ======================

We are running asterisk with a single POTS line for local calls and a voip line for long distance. Whenever we receive a call on the POTS line it is more than likely, but not always, going to have significant distracting echo. In addition to that there is occasional heavy crackle or static. I have tried to follow the guidelines at :

I am finding that I have to increase the txgain in zapata.conf to 8 when my X101P is connected to my BT phone line, otherwise people can hardly hear me. This then gives echo issues. Do other people have the same problem on BT lines. I was wondering if I should give BT a call and get them to increase the gain on the line. Strange though as the rxgain is OK and I don't have this problem with

I have a * box running * version 1.0.3 with two X100P line cards in it and Cisco 7960 IP phones. Everything seems to work pretty well with the exeption that the system hangs up on phone calls for no apparent reason. It does this on both incoming and outgoing calls through the POTS line (currently only have one). The only thing in the asterisk console with maximum verbousity is " -- Hungup

Has anyone been able to sucessfully use 2-4 X101P clones with Asterisk on a single system ? I'm using one Encore MD 3200 modem sucessfully, alongside a TDM400P (3 FXS, 1 FXO) and would like to be able to use up to 4 X101P on a single system. In most cases I'll have 2 or 3 instead. I understand all the issues with interrupt sharing and PC motherboard quality. Just need to know if any