similar to: EuroISDN and Sangoma Card

Hello, I've recently bought a new Sangoma A104d PCI-card. WANPIPE release is 3.4.7. Machine is a dual Xeon with Debian 5.0.3. Asterisk is 1.6.11 with recent libpri and dahdi. When I boot the machine (including hardware and wanpipe and dahdi drivers) and start asterisk, everthing runs fine for almost 5 minutes. Then every few seconds HDLC errors occour. I also tried booting - and starting

Does anyone have any experience ith configureing the sangoma A102 card for testing using a e1 cross cable i've configured and installed the cards properly even the lights on the card are green which proves that my cross cable is properly built too. my problem is with asterisk which gives me these errors PRI got event: HDLC Abort (6)on Primary D-channel of span 1 PRI got event: HDLC Bad FCS

Hello, I have following problem with Sangoma A104 card: CLI> pri show span 1 Primary D-channel: 16 Status: Provisioned, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 10000 T305 Timer: 30000 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI

Hi, Recommending to go Digium because of an OpenBSD issue with the Sangoma A104D is quite funny to say the least since neither is the TE407P supported in BSD by Digium. So the recommendation is useless to the person who originally requested for a comparison between the two products. If someone wanted to send back the A104D, he could have taken advantage of Sangoma's 30 day money back

Hi, I am facing an audio-problem with the dial application and I (!) think, that it is connected to the dahdi parameter "overlapdial=yes". Sangoma support does not see any connection between this. But when enabling this option I face with some(!) dial-partners a audio one-way issue (the called party can not be heard). Only using PSTNS (germany e1 trunk) - no voip. Is there any

Hi ! We curently have a centos 5 / asterisk 1.4 server that we have some DTMF problems with. It has a Sangoma A104d card and only port one is used to connect to the PSTN. Port 2 is conencted via a cross-over cable to a RAS for modem access and port 3 is connected for data communication via PPP. Now, I want to freshen this setup to something newer. So I installed a Scientific Linux 6 server,

Hi Sangoma a104 card have in product specyfication support for Line protocol SS7 , http://www.sangoma.com/products/p_aft-104-specs.htm [..] Line protocols Frame Relay, X.25, HDLC, PPP, SS7, Transparent bit-stream, BSC. [..] Anyone of you guys use line protocol SS7 for E1/T1 termination in asterisk ? As far I know asterisk don't have support for SS7 signaling, but my telco wants to setup

Hello List! I wanted to share to everyone the following compatible connectivity products that my company installed in our Asterisk based soft switch. I already sent these to the Asterisk.org site many days ago but for some reason they still have to post it. 1. Sangoma A101 single port E1/T1/PRI Card 2. Sangoma A102 dual port E1/T1/PRI Card 3. Sangoma A104 quad port E1/T1/PRI Card 4. Sangoma

Hello, Several people asked to get a hold of the stats I used to determine that the Sangoma T1/E1 boards performed better in our real-world tests than the Digium boards. We've decided to post our results after confirming them over the past month of operations. Here is a link to the last two reviews I wrote about Sangoma with Asterisk:

My Sangoma Experience in Asterisk: Followup 2005-05-06 original review can be found at: http://astguiclient.sourceforge.net/Sangoma_experience.txt It's now been a month since I finished my last round of tests with the Sangoma A104u board in Asterisk. I have had a lot of conversations with the guys at Sangoma about how my system runs so that they could set up their test systems to try to

I have a system that I am trying to get a port on a Sangoma A104d card connected to an Adtran 850 with 5 FXS modules and 1 FXO module. A problem I am having is figuring out what cable should be used from the port on the Sangoma to the JP2 port on the Adtran. Tried was a cross-over T1 (1->4, 2->5, 4->1, 5->2) as well as a straight T1 (1->1, 2->2, 4->4, 5->5). Neither one

Hi all, My problem boils down to these errors: ... Unable to create channel of type 'ZAP' (cause 34 - Circuit/channel congestion) == Everyone is busy/congested at this time This is triggered by lines in extentions.conf such as: exten => _X.,1,Dial(ZAP/g1/${EXTEN},,W) The system is CentOS v5.2 with Asterisk 1.4.23 (druid-asterisk-1.4.23.1-2), a Sangoma A104

Hi, I have Sangoma A101DE 1 Port E1/T1 With Hardware Echo Cancellation ( PCI Express ) Card installed on the box. *Its not detected.* Details are as below :- [root at asterisk ~]# lspci 00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 01) 00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:04.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:05.0 PCI bridge: ATI

I am having a problem trying to get a Sangoma A101 to work with Unicall. I have installed the sangoma drivers and everything seems to be well but when I try to run ztcfg I get the following error: CAS signalling on span 1 conflicts with HDLC with FCS check on channel 16. Here is my /etc/zaptel.conf # MFC/R2 normalmente no usa CRC4 span=1,0,0,cas,hdb3 cas=1-15:1101 dchan=16 cas=17-31:1101

Hi, I am trying to validate a setup with a sangoma A116 card (16PRI in one card). I currently have two machines set up, each with a sangoma A116 card. Those are interconnected with crossed PRI cables. One of them is in NT mode, the other in TE. The ports are configured in E1 mode, asterisk is all set up and I can make calls between them, filling up all 480 (16 * 30) channels. Now, I learned

We have several Sangoma cards that we used during a transition time in our the replacement of our legacy voice system that we no longer need. Each of them saw about a month of service and are in good working order. We'd be happy to get 70% of retail for them. They are as follows: qty 2 A104D PCI w/ on board echo cancelation - $1500 each qty 1 A102D PCI w/ on board echo cancelation - $1050

Hi all, as good? I try to install asterisk-1.2.14, zaptel-1.2.12,libpri-1.2.4,addons-1.2.5 , sounds-1.2.1 and wanpipe-2.3.4-3 and hwec-utils-beta4-2.3.4 But it is not compiling drivers of the Sangoma, why udev's for board in "/dev/zap"(1-31, channel,ctl,pseudo,timer) is not created. But when I install a board TE110P Digium, udev's is created and asterisk functions perfectly. : )

Hi all, We are running Asterisk 1.2.7.1 on our Dell Poweredge 2850 and are having massive sound quality issues. We are experiencing call quality issues for our remote location, namely calls cutting out and breaking up for our agents. The two main issues seem to be 'popping' and 'dropping' - popping would be pops and crackles on the line, where dropping would be complete audio

Hey Guy, I have quick question. I am purchasing Sangoma A102D card but i am confused between PCI and PCI Express. Which card would be good for me. Definitely PCI Express is advance but i just want to know is there any major difference, like quality, performance etc.. -Satish -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable