similar to: Dropped calls continued

Hi again, I'm trying to setup our non pri T1 (they call it a Long Distance T1), our current pbx has the signaling set to E&M, I can set em in zapata.conf, but I'm trying to track down the proper entries for the zaptel.conf file. The digium docs only show a PRI example. Our current system has these settings: Signalling: E&M Framing mode: ESF Line Coding: B8SZ here's my

Howdy, New installation, trying to connect an RBS T1 with AMI/D4 framing and E&M Wink. Using a Sangoma A102d and asterisk 1.4.22-2 on Centos5 (Trixbox 2.6.2.1). Outbound calls work fine, but inbound calls fail to read the DID information, and with debug set to 10 I get the following: [Feb 2 19:40:23] DEBUG[25184] chan_zap.c: Monitor doohicky got event Wink/Flash on channel 3 [Feb 2

I am trying to make an in/out trunk group comprised of 4 DS0's using E&M Wink signalling. The first four channels of a DS1 on a T100P are being used for the group. Outbound calls work fine, but inbound calls fail. The other 20 DS0 channels are used for a PRI. Does the configuration shown below look okay? I've tried setting 'immediate => yes' without success, but it

Hello, I'm trying to make my asterisk box to act as a telco, in order to reproduce a US environment in europe. Our telco provider is giving us those settings: ESF B8ZF Inbound = E&M Immediate Outbound sig =Wink Start Yield to Glare = Yes Those trunks are using CAS for signaling. I have tried many configs/combinations in zaptel.conf and zapata-channels.conf In zaptel.conf, when having

Does anyone know the default E&M Wink timings for Nortel DID ports? The default settings on Asterisk are: ; prewink: Pre-wink time (default 50ms) ; preflash: Pre-flash time (default 50ms) ; wink: Wink time (default 150ms) ; flash: Flash time (default 750ms) ; start: Start time (default 1500ms) ; rxwink: Receiver wink time (default 300ms) ;

I currrently have Asterisk 1.2.8 with a TE110P Zaptel card tied to our Nortal DMS-10 switch via T1. This T1 trunk is configured for Feature Group D MF. The purpose of this is for LD delivery to a VoIP LD provider as a LD choice for our customers off of the DMS-10. When I sieze a channel on the zaptel, I get a spill of digits from the switch that is the called number, and I can see that in

Hi everybody, Well, I've finally got asterisk to to talk nicely with my Intertel pbx. Currently there is a outside T1 line (e&m wink start, esf, b8zs) connected to asterisk, and then asterisk connected similarly to my Intertel pbx. For right now all asterisk is doing is passing calls between the two. When I call out from the pbx, I can connect perfectly to the outside world. When I

I've got a new setup (different building) where Asterisk is sitting between the PBX and phone company on a E&M T1 line. Mitel PBX <-> Asterisk <-> Phone company Inbound works. Asterisk gets the in-band digits from the phone company and hands the call off to the Mitel just fine. Outbound is weird. Asterisk seems to expect that the mitel will send routing information

Asterisk is getting red alarms on my T1, sometimes once or twice a day, but today it happened 5 times. Even once is too many. Every call in progress is dropped. Please help! What do I need to do? What can I try? I've googled and searched this list and can't find anything. Here's an example from the logs: Feb 7 13:37:54 WARNING[32451] chan_zap.c: Detected alarm on channel 6: Red

Hello All, I've mostly solved my DID problem from a few days ago. Apparenly the lines weren't configured properly. Now heres the next question. 12 E&M wink lines from telco. I have them all plugging into an Adtran 750 with FXS cards. The Adtran ports are configured DPO. How do I signal this from Zaptel. I have them setup E&M in zaptel.conf and EM_W in zapata.conf. They

> Post your extensions.conf and what's on the CLI (asterisk -r) As requested: # cat /etc/asterisk/extensions.conf [incoming] exten => s,1,Answer() exten => s,n,NoOp(CallerID is ${CALLERID}) exten => s,n,NoOp(DID is ${DNID}) exten => s,n,Background(enter-ext-of-person) exten => 1625,1,Playback(digits/1) exten => 1625,n,Goto(digits/1) exten => i,1,NoOp(CallerID is

Hi All, I have a rather peculiar problem. Whenever I dial out over ZAP/g0 the phone will just ring and ring, even if I answer the phone on the other end. Whats strange is that the * phone will continue to ring even after I've answered and (sometimes) hung up the dialed phone. If I make an extension to just directly dial out on ZAP/1, its almost the same behavior, it will continue to

We're having some difficulty connecting a T1 fax board card to asterisk, with E&M Wink. We've successfully connected it to other E&M Wink T1s, but have been unable to get asterisk to hear it's dialing. Asterisk can dial down to it with no problem, and it hears all the digits, but whenever it sends digits down to asterisk, * always only "gets" the first one. This is

We have 2 T1's coming from our phone switch to a digium TE220B. We have managed to get CPN and the extension outpulsed from the switch, but call setups are really slow. Our T1's are set up as E&M Wink, and they send us the last 5 digits dialed followed by the 10 digit calling party number (we couldn't get the switch to be happy with *CPN*+5* to use featd). We are using asterisk

Hello All, I'm trying to connect Asterisk to an Executone phone system with an analog DID card and I'm hoping someone can help me figure out what I'm doing wrong. The Executone DID card provides battery to the telco, when the telco wishes to dial a DID it goes off-hook, waits for a wink from the Executone and then dials the last three digits on the number with pulse (as opposed

Hi, Did anyone manage to connect either Digium or Sangoma T1 card to any other PBX/gateway using T1 E&M Wink/Wink signaling? I'm trying to connect Avaya Definity to an Asterisk box with T100P and so far no luck. (I know I can do so with ISDN PRI, but need an additional ISDN processor card for Definity.) I tried to connect Definity to Cisco 3640 CCME (call manager express) to test the link

Attempting to talk to an Eagle Telephonics switch at a disaster exercise. Didn't think a plain old E&M wink start T1 would be this much of an issue. We finally got the Eagle to accept a call from *, but whilst I can hear the person on the Eagle, they can't hear me. When they initiate a dial out I only get the first 2 digits from their switch... Does anyone have decent

I have a couple of live T1s sitting around and they are not ISDN(like most of the people that are using Asterisk seem to be using), they are regular old 24 channel, robbed-bit, E&M wink start, D4AMI T1 circuits. Can I get these T1s to work with a T100P Digium card and asterisk? Searching through the lists and the documentation I haven't seen any examples of how to configure this kind

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

I'm having various issues that may or may not be related to each other (I'm pretty sure they are). We've had this system for a year now (quad T1 card, right now we have 1 T1 coming in, 2 going out to channel banks) and we've had intermittent "ghost" calls--it appears that what is happening is a call is made, the number being called is disconnected/busy/answering