Displaying 20 results from an estimated 10000 matches similar to: "TDM-400 doesn't detect far-end hangup"
2006 Mar 16
1
module load order for Junghanns qozap and TDM card
Hi all,
I'm trying to get a junghanns QuadBRI to coexist in the same machine as a
Digium TDM400P card (so I can run the ISDN lines in and bridge with analog
phones plugged into the TDM).
I'm having a problem loading the modules. If I follow the BRIstuff
(0.3.0-pre-1l) install method.... it's to modprobe zaptel, then insmod
qozap.o
I'm on Debian 2.4.31.
That works.
But then I
2006 Apr 26
1
Problem with a TDM-400P
(Sorry of this appears in the list twice, but I wasn't sure if it was
blocked or not)
Hi there,
I'm having a problem with my TDM-400P which has been working like a
charm up until very recently. It started to fail last week, and so I was
hoping someone could illuminate me with some information as to why. Its
configuration is as follows:
------------
FXS (green) module is in position 1,
2006 May 09
2
Problems with TDM400P and FXO modules
Hi , I have an asterix (1.2.7.1) box with 3 TDM400P and 10 FXO modules, and
zaptel (1.2.5).
The problem is that 6 modules can't be initaized and i get the folowing
error:
May 7 09:17:37 WARNING[7739] chan_zap.c: Unable to specify channel 9: No
such device
May 7 09:17:37 ERROR[7739] chan_zap.c: Unable to open channel 9: No such
device
here = 0, tmp->channel = 9, channel = 9
ztcfg output
2004 Dec 10
2
Asterisk 1.0.3 - Signaling on E100P.
Hello list ,
I?m putting to work a new asterisk box.
I?m running * 1.0.3 with (one )
Wildcard TDM ( 2FXS* 2FXO) and
(one) E-100P.
Both boards are working well. ztcfg
don?t show me any error.
zttool list both cards as "OK"
But when i run asterisk on verbose mode
i get those errors :
[chan_zap.so] => (Zapata Telephony)
== Parsing '/etc/asterisk/zapata.conf': Found
--
2006 May 04
2
Unable to get TDM400p working
This has got to be a stupid error I'm making...
I have been experimenting with different hardware and software
configurations before I decide what to use as a production platform. Up
until just recently things were going well.
But now it appears I'm unable to get access to my TDM400p from Asterisk. I
know the TDM card works fine, used it in another machine where it
performed flawlessly.
2006 Jun 08
2
hangup lag causing the answering of already answered calls
I have a TDM-400P with one FXO module. On an incoming call, I have set
Asterisk to dial my phone (exten => s,1,Dial(IAX2/carey)), which is
basically the only thing in my dialplan.
When the call is answered by the PSTN phone first, or when the ringing
call is hung up, Asterisk keeps ringing for 5+ seconds, which causes
trouble (the answering of already answered calls).
I noticed in the
2003 Apr 24
3
Re: two computers set up ... now what?
***
Now you just need a "phone" or "station" (FXS) device and a method of
connecting it.
***
So... essentially I need to spend another $125 US on a Wildcard TDM400P so I
can plug in an analog phone?
On the X100P description it says:
"The X100P supports FXS Loopstart and "Kewlstart" (Loopstart with far end
disconnection supervision). It can detect ringing and
2006 Jun 12
1
TDM-400 and dialplan -- how to ring a SIP ex tension *before* answering the PSTN line?
the caller is out his money anyway when you call any phone and voicemail
kicks in, although i think on a payphone they give you a 2 or 3 second
window to hang up.
Suggest you implement i'm here / i'm away dialplan logic or set the do not
disturb button that way when someone calls and the guy is away it hits
voicemail right away and the caller can hear this and still have the 2 or 3
2004 May 19
4
TDM400P problems with 1 FXS, 1 FXO
Hi-
I'm totally stumped configuring my TDM400P with one FXS and one FXO
module. Before I got the FXO module, I used to have an X101P, and
everything was working very well. Now * doesn't seem to recognize the
FXO channel. I've searched the wiki and the list archives. Stock Debian
3.0 stable installation. Any advice? Thanks.
-- David
Here's my configuration:
modprobe zaptel
2003 Aug 07
2
Newbie Issue
Hi All,
I recently purchased the Asterisk Developer's Kit (TDM) to try out
Asterisk. After following the directions in the Digium's FAQ topic entitled
"Q. How do I configure my TDM40B and X100P?", I'm receiving the following
error:
WARNING[1074428608]: File chan_zap.c, Line 6748 (load_module): Ignoring
rxwink
ERROR[1074428608]: File chan_zap.c, Line 6692 (load_module):
2008 Jan 08
6
[Zaptel] Checking that TDM card works?
Hello
Since TDM cards are known for being particular when it comes
to motherboards (PCI 2.2, etc.), I was wondering if there is a utility
that can check that the Zaptel driver works OK and can tell if the TDM
card is compatible?
That way, if an FXO module is not reporting an incoming call, we'd
know it's because of the Zaptel driver, and not something elsewhere.
Are "dmesg",
2003 May 01
1
TDM cards and Asterisk
I have put a box together using 2 X100P and 2 TDM400 4port cards.
Using the simple setup that Martin posted a few days ago, I have
asterisk almost up and running.
/etc/zaptel.conf
fxsks=1-2
fxoks=3-10
loadzone=nz
defaultzone=nz
(I have added NZ tone information to zaptel and Asterisk - I'll submit a
patch soon).
/etc/asterisk/zapata.conf
[channels]
context=incoming
signalling=fxs_ks
2008 Oct 20
1
Zaptel FXO offhook when connected to PSTN
I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having
an annoying issue with the FXO ports. As soon as I plug either one into the
phone line it's as though the line is disconnected i.e. get disconnected
tone when trying to dial out, line is busy when dialling in.
The CLI shows the following:
trixbox1*CLI> zap show channel 4
Channel: 4
File Descriptor: 18
Span: 11*
2009 Dec 21
3
TDM 400 hardware(?) issue
I am having to abandon asterisk after having used it for 2.5 years due
to this problem. Every couple of days (sometimes more often, sometimes
less), the machine will lock up because the TDM board or the Dahdi
driver goes south. /var/log/messages starts filling up with repeated
messages:
kernel: TDM PCI Master abort
The card I have is:
*CLI> dahdi show status
Description
2005 Jun 22
4
TDM400P DevKit Problem
I installed the TDM400P and installed it on a system running on Fedora
Core1, please refer to the steps below. I connected an analogue phone to the
FXS port.
When I pick up the speaker I don't hear the dialtone although when I press a
number key I hear a DTMF generated. What could be the problem?
I appreciate your help
1- First I installed the TDM400P in the PCI slot and connected
2005 May 30
2
Error in Zapata Config?
When I reload the config, I see this error in the CLI. However, I don't see
what I have done wrong:
== Parsing '/etc/asterisk/zapata.conf': Found
May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring
signalling
-- Reconfigured channel 1, FXO Kewlstart signalling
May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring
signalling
-- Reconfigured
2006 May 27
3
TDM
The TDM01B is 4 port capable but has only 1 FXO module. I'm running asterisk
1.2.7 and zaptel 1.2.5. I cannot seem to get the TDM01B working. When I do
the zttool it shows 4/1/0. I can dial out from a POTS phone up to the point
that the cable plugs into the card.
Here is my /etc/zaptel.conf
loadzone=us
fxsks=1
and here is my /etc/Zapata.conf
[channels]
language=en
#include
2007 Mar 12
2
TDM-400, Polycom SIP phones, and echo problems
Hi:
I am working on a new system with a TDM-400P card with three FXO modules
and one FXS module.
The system has been in place for a week. Users are complaining of echo
problems. I have noticed this echo myself. It varies in severity. It is
sometimes bad enough to make it difficult to converse, but the users
find it generally unacceptable. They miss their old phones, which just
worked. As you can
2006 Dec 11
1
Power requirements on the TDM-400 card
I have a TDM-400 from digium with 2FXO+2FXS ports. Any idea on how much power
will this drain from the 12 and 5 V connector when all ports are in use?
--
Gustavo Felisberto
(HumpBack)
Web: http://dev.gentoo.org/~humpback
Blog: http://blog.felisberto.net/
------------
It's most certainly GNU/Linux, not Linux. Read more at
http://www.gnu.org/gnu/why-gnu-linux.html .
-------------
2008 Apr 14
4
Unable to load module chan_zap.so
I am having trouble with chan_zap.so not loading. When I load it from
modules.conf, Asterisk bails out without any error message. When I
load it from the console, it just says "Unable to load module
chan_zap.so" no matter what verbose level I am using.
dmesg says:
Zaptel Version: 1.4.4
Zaptel Echo Canceller: MG2
Freshmaker version: 73
Freshmaker passed register test
Module 0: