similar to: Problems with TDM400P and FXO modules

I am having trouble with chan_zap.so not loading. When I load it from modules.conf, Asterisk bails out without any error message. When I load it from the console, it just says "Unable to load module chan_zap.so" no matter what verbose level I am using. dmesg says: Zaptel Version: 1.4.4 Zaptel Echo Canceller: MG2 Freshmaker version: 73 Freshmaker passed register test Module 0:

I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected

I have a TDM400. Just updated Fedora 12 to kernel 2.6.32. Rebuilt and installed dahdi-2.2.1. kernel modules loaded. lsmod | grep wctdm wctdm 37233 0 dahdi 194985 1 wctdm lsmod | grep dahdi dahdi 194985 1 wctdm crc_ccitt 1549 2 dahdi,isdnhdlc dmesg: dahdi: Telephony Interface Registered on major 196 dahdi: Version: 2.2.1

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

Can someone please help me with my config settings for my TDM12B. I have got the FXS port to work fine, but I cannot get asterisk to startup with any settings for the fxo ports. It appears to be something related to the message "Signalling requested is FXS Kewlstart but line is in FXO Kewlstart signalling". However, I have tried what appears to be every possible configuration option. I

I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*

From asterisk -cvvvvv == Parsing '/etc/asterisk/chan_dahdi.conf': == Found == Parsing '/etc/asterisk/users.conf': == Found -- Automatically generated pseudo channel [Nov 11 17:43:28] WARNING[5756]: chan_dahdi.c:18155 process_dahdi: Ignoring any changes to 'userbase' (on reload) at line 23. [Nov 11 17:43:28] WARNING[5756]: chan_dahdi.c:18155 process_dahdi:

I have seen this in the archives any number of times -- but I have yet to find a solution that works for me. Any suggestions you can offer would be most appreciated. Here are the answers to the questions I have seen asked in earlier posts. The log contains: Mar 10 12:26:29 WARNING[3015] chan_zap.c: Unable to specify channel 4: No such device Mar 10 12:26:29 ERROR[3015] chan_zap.c: Unable

Greetings all, I'm new to asterisk... Finally got two IP phones and two TDM400P's (one with four FXO modules and one with four FXS modules)... Began experimenting a couple days ago and have ran into a very aggrevating problem. My system consists of the following hardware: Abit BL7-RAID motherboard Pentium 4 1.6GHz processor 512MB SDRAM 2 TDM400P cards 2 3Com 3c905

As best i could figure it out, I've installed dahdi and rc4. My TDM400P doesn't answer fxo or fxs. /etc/dahdi/system.conf: loadzone = us defaultzone=us fxoks=1,2 fxsks=4 /etc/asterisk/chan_dahdi.conf: [house-phones] context=internal ; Uses the [internal] context in extensions.conf signalling=fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel dahdichan => 1 ;

(I'm producing a writeup on all the things one run into building an * box. Which after a couple of boxes is showing up aplenty.) So this uses the working h/w and config's from another box. All I do is build in a new computer. Loading the modules I got: __________________________________________________ Zaptel Configuration ====================== Channel map: Channel 01: FXS

The REV I card shows up in the PCI table as: 02:05.0 Network controller: Tiger Jet Network Inc. Intel 537 (or 02:05.0 Class 0280: e159:0001) Subsystem: Unknown device b119:0001 But the REV E/F shows up as: 02:0d.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface (or 02:0d.0 Class 0780: e159:0001) Subsystem: Unknown device b100:0003 One

I get the following errors when starting Asterisk. == Parsing '/etc/asterisk/zapata.conf': Found Feb 19 21:14:35 WARNING[10440]: chan_zap.c:920 zt_open: Unable to specify channel 1: No such device Feb 19 21:14:35 ERROR[10440]: chan_zap.c:6860 mkintf: Unable to open channel 1: No such device here = 0, tmp->channel = 1, channel = 1 Feb 19 21:14:35

I'm afraid that I am at a loss here. I am new to Asterisk, and have successfully set up SIP. But I cannot get my FXS card working, and I'm not sure what else I can try. # modprobe wcfxo /lib/modules/2.4.21-37.0.1.ELsmp/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may

hi you, I'm having problem with voice quality on my trixbox using TDM2400B.The trixbox is connected via 20 FXO ports on a TDM2400 with the hardware echo cancel module. Echo cancel almost works, but the users hear what they describe as a 'background crackle/buzz' coming back when they talk. anyone have the same problem? pls help me. thanks a lot. my trixbox and config

Hello Since TDM cards are known for being particular when it comes to motherboards (PCI 2.2, etc.), I was wondering if there is a utility that can check that the Zaptel driver works OK and can tell if the TDM card is compatible? That way, if an FXO module is not reporting an incoming call, we'd know it's because of the Zaptel driver, and not something elsewhere. Are "dmesg",

Hi. I am having problems with dahdi using kernel 2.6.32. I am using 2.6.30 kernel and it works fine -- here is the output of dahdi_cfg -vv ++ dahdi_cfg -vv DAHDI Tools Version - SVN-trunk-r8670 DAHDI Version: SVN-trunk-r7445M Echo Canceller(s): Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 01) Channel 04: FXS Kewlstart

Hi: I?Bought TDM2400P ,with 24 FXO ports , I installed? the asterisk 1.4.28 and?dahdi 2.2.0?and then i compiled them and configured all, i pluged into 8 pstn line into the Rj connector and then i got messages on asterisk console that alarm cleared on channels 1->8??, at this step everything should go fine ,but when i try to make a call?through the TDM?there is silence and no audio,and then i

Hi all, I bought a Sangoma A200 card from an online supplier and explained exactly what I wanted, 3 incoming phone lines to PBX and a life line (some where to connect a standard BT phone to the PBX incase the power goes, making the BT phone ring). I was told to order 1 x FXS module (2 FXS ports) 2 x FXO modules (4 FXO ports) However being a complete noob, I have connected the 3 lines to the

Hi: I had an fxo card from Digitnetworks and it was working fine on my Asterisk box. I then replaced it with TDM04B. I changed the zaptel and zapata to include the four channels. When I run ztcfg, I get configuration errors: Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: