similar to: Config with TE210P, Asterisk and Legacy PBX and FreePBX?

Hi list! I'm trying to setup a new * server with a TE210P in a Dell 2850 box. I'm using zaptel version 1.2.5, the linux flavour I'm using is CentOS 4. In a previous thread I read about the results I should expect from zttest. On my home box (using the crappy Asus A7V600) I got really bad results from zttest (just over 97.5) but I know that this motherboard just sucks. To my

Hi all, I'm going to configure a middle asterisk installation. I'll use a TE210P to connect a T1 channel bank and a PRI E1 line. I'm thinking on using a SuperMicro P8SCT Mother Board that has a 1x 64-bit 133MHz PCI-X 3.3V. In TE210P documentation I've read: The TE210P is a 32-bit 33MHz card keyed for 3.3 volt operation. Can SuperMicro slot (that is a 133Mhz slot) be used

Hello, I have been struggling with the configuration of this card on my box. I have a T1 line and I am trying to setup asterisk with it. I followed all the instructions and I still see a blinking red light on the card. I use fedora 12. If everything is fine should I see a green line when I plug in the T1 line ? I want to isolate the issue so I di not start asterisk. When I run asterisk I get

Hi all, My asterisk (1.2.4, zaptel 1.2.2) running in Dell PowerEdge 830 box is having problems with Digium TE210P card that I use for PRI connection. My problem is stability. Sometimes the box just boots OK with a full functionality, no problems at all, sometimes (after power outage) it halts during boot with the amber control LED flashing. Sometimes (most frequent scenario) it just boots OK and

Hello, I recently acquired a Digium TE210P for a faxing solution I'm working on. I would like to use the card to send faxes from my infrastructure using Asterisk and HylaFAX. I'm curious if the zaptel driver will recognize in/out faxes to/from the TE210P. Is this going to work or should I not even try? Thank you in advance, I greatly appreciate it. -Dan -------------- next part

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I am stuck in a situation where I have two te110p's and really need a te210P. Anyone interested in a trade? They are in working condition guaranteed. If this is the wrong forum for this, I am sorry... I will take it off list. -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.2 (MingW32) Comment: Using GnuPG with Thunderbird -

Has anyone every attempted to set up a mini PC to achieve much the same functionality as the fonebridge box? The sort of thing I'm imagining is a micro itx board & case in a completely solid state configuration (flash disk, maybe a psu fan but only if really required), with a TE210P (or equiv) card(s). The sole purpose of this would be to be a bridge between E1 lines and TDMoE. The

We performed a server hardware refresh recently here -- went PCI-x, and now I have 4 extra PCI interface cards that I'd like to find a good home for. These have been extremely solid cards, all of them also have the hardware echo cancellation modules. http://www.voipsupply.com/dgm-te210p Please contact me off-list if interested! -- Mahlon E. Smith http://www.martini.nu/contact.html

Dear all I have now install TE210P 2 port E1 card on asterisk 1.4.10 on centOS 5 but thing is that i have connect 1 E1 port with avaya E1 back 2 back and second E1 card on Direct Telcom for outgoing for outside now i got this error when i call on avaya PRI asterisk think PRI_CPE and remote end also CPE i have configure /etc/zaptel.conf span=1,1,0,ccs,hdb3

Hello all. I have an NEC PBX connected via a TE210p E1 line to an asterisk 1.6 box. NEC -> E1 -> TE210P:1 -> * -> TE210P:2 -> E1 -> Telco Incomming calls from the telco to the asterisk box to the NEC work fine with indials and everything. Works sweet. Outbound from the NEC to the Asterisk box fail. Giving an long dial tone that then times out. Ie, pick up NEC handset, dial

hello everybody, one of our customers which wants a soft transfer between his old pbx to asterisk and sip. the setup is as follows: telco <---pri---> asterisk <---pri---> legacy pbx everything is fine exept that when dialling from the legacy pbx it takes about 3 seconds before the asterisk start to dial. where does this delay come from? has it to do with

Hello, I'm just starting out with asterisk and I'm playing around with the system. Currently I have a Digium TE210P connected to a PRI on the Asterisk server. I have a SIP soft phone on my laptop for testing that is working fine. When I try to place a call from my soft phone I get this from Asterisk: May 1 09:11:41 NOTICE[20098]: app_dial.c:1029 dial_exec_full: Unable to create

Hi list! I have some sip phones and Sipura ATA 2000's. However after dialling a number I need to dial a # to control a device. When I dial # Asterisk kicks in and puts the call on hold. How can I change this? Thx!! Remco

Hi list! I managed to come reasonably far (farther than I thought I would) but have two problems. I still need to pass calls to the Legacy PBX for Fax (I need it as a channel bank). I have calls coming in into asterisk, that works fine. Based on the DID I can route calls to the Legacy PBX but I'm puzzled how. I guess I need a new dial command for that? All fax calls are now coming in a

Dear all anybody have idea of this 2 card and performance vise which one is suggestable ??? ----PGP Signature-- Satish Patel mobile:- +91-9818875535 http://www.linuxbug.org --------------------------------- Be a better sports nut! Let your teams follow you with Yahoo Mobile. Try it now. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, I'm running Asterisk@home 2.5 asterisk 1.2.4 zapatel 1.2.2 libpri 1.2.2 on a Dell Poweredge 2850 (1 CPU) with a TE210P I have 2 t1 circuits using NFAS with dchan on 24 and no backup dchan. I am able to receive inbound calls on all channels and can only make outbound calls on channels 25-48. Attempting to make an outbound call on channels 1-23 results in congestion.

Hello Fellow Users, This is my first post so please be kind :-) I am using asterisk@home <mailto:asterisk@home> with freePBX talking to an Alcatel 2400 analogue port via a Digium TDM01B - 1 FXO card I can make calls into the asterisk by dialling the asterisk extn number from the 4200. I can dial extns on the 4200 from asterisk by dialling 9(4200extn number) if I don't have any

On Mon, 2007-05-14 at 23:41 +0200, vax9000 at gmail.com wrote: > Full_Name: vax, 9000 > Version: 2.4.0, 2.2.1 > OS: 2.4.0: Mac OS X; 2.2.1: Linux > Submission from: (NULL) (192.35.79.70) > > > To reproduce this bug, first go to the website "http://llmpp.nih.gov/DLBCL/" and > download the 14.8M data set "Web Figure 1 Data file". The direct link is >

Hello everyone. I have server with 2E1 PCI card, asterisk 1.4.35, dahdi 2.4.0, libpri 1.4.12-beta2. One PRI trunk looks to PSTN and take a clocksource from telco. Another trunk looks to PBX with DECT system. Some outgoing calls from asterisk to PSTN drops. The last message that exists before hanging up process is: DEBUG[28467] channel.c: Got a FRAME_CONTROL (8) frame on channel DAHDI/... This

IPManager version 1.6 has just been released. Below is a list of some of the features you will get on your Asterisk server using IPManager to generate your configuration files. Download: http://ipsoftware.thorben.dk <http://ipsoftware.thorben.dk/> PBX Features The following features will be available to users of the PBX if you are using IPManager to configure your PBX. *