similar to: Bad FXS Module?

The REV I card shows up in the PCI table as: 02:05.0 Network controller: Tiger Jet Network Inc. Intel 537 (or 02:05.0 Class 0280: e159:0001) Subsystem: Unknown device b119:0001 But the REV E/F shows up as: 02:0d.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface (or 02:0d.0 Class 0780: e159:0001) Subsystem: Unknown device b100:0003 One

hi guys, i got a TDM400P FXS card an everything is fine except for this when i do modprobe wcfxs , the linux shows 2 TigerJet Network Inc Model 300 128k. i don't know why it is showing 2 of them. or is that what it is? ERROR: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 0 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 0 cshould be

Hi, I'm trying to get up and running a TDM400 with a standard italian pots line but i'm having problems at getting asterisk to detect when the line get answered on outgoing calls. I'm using asterisk 1.6 beta 9 with zaptel 1.4.11. I tried with and without answeronpolarityswitch=yes but it didn't change anything at all. With callprogress=yes answer get never detected. With

Hi, I have received a new card TDM400P revision E, from digium. When I tried to modprobe wcfxs it gave me the following errors: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 255 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 255 should be 2 Module 1: Not installed ProSLIC on module 2 insane (1) 255 should be 2 Module 2: Not installed

I just installed an FXS module onto a 4 channel tdm thats about 5 years old and it wont work. Running dmesg I can see the following error: Zapata Telephony Interface Registered on major 196 Freshmaker version: 71 Freshmaker passed register test !!!!!!! LOOP_CLOSE_TRES iREG 1C = 1 should be 1000 !!!!!!! RING_TRIP_TRES iREG 1D = 8000 should be 3600 !!!!!!! COMMON_MIN_TRES iREG 1E = 0 should

Hi, I have Wildcard TDM400P with 2 FXS y 2 FXO. After all work fine but now do it: ----- load driver: wctdm y zaptel (zaptel-1.2.1) Module 0: Installed -- AUTO FXS/DPO Unable to do INITIAL ProSLIC powerup on module 1 Unable to do INITIAL ProSLIC powerup on module 1 Module 1: FAILED FXS (FCC) Module 2: Installed -- AUTO FXO (FCC mode) Module 3: Installed -- AUTO FXO (FCC mode) Found a

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

Hi all, I was wondering if anyone had any pointers on how to determine whether or not a module has gone wonky on the TDM400P? I have a 2 FXO (channels 3 and 4) and 2 FXS unit (channels 1 and 2). The bad (?) module in question is the FXO module on channel 3. I can't dial in to or out of that channel; dialing in gives a busy signal, dialing out just shows * hanging around after attempting a

I have a TDM400. Just updated Fedora 12 to kernel 2.6.32. Rebuilt and installed dahdi-2.2.1. kernel modules loaded. lsmod | grep wctdm wctdm 37233 0 dahdi 194985 1 wctdm lsmod | grep dahdi dahdi 194985 1 wctdm crc_ccitt 1549 2 dahdi,isdnhdlc dmesg: dahdi: Telephony Interface Registered on major 196 dahdi: Version: 2.2.1

Hello, I have few questions about Asterisk. I installed Asterisk from CVS on FreeBSD and I made cvsup 2 days ago. 1.I couldn't find Asterisk version using "asterisk -V" command. How can I to find version information? 2.I am using Wildcard X101P (FXO) and Wildcard TDM400P REV E/F (FXS)on it. I tried Asterisk CallerID feature, but unable to get it. I tried callerid signaling V23,

I am having trouble with chan_zap.so not loading. When I load it from modules.conf, Asterisk bails out without any error message. When I load it from the console, it just says "Unable to load module chan_zap.so" no matter what verbose level I am using. dmesg says: Zaptel Version: 1.4.4 Zaptel Echo Canceller: MG2 Freshmaker version: 73 Freshmaker passed register test Module 0:

I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected

From asterisk -cvvvvv == Parsing '/etc/asterisk/chan_dahdi.conf': == Found == Parsing '/etc/asterisk/users.conf': == Found -- Automatically generated pseudo channel [Nov 11 17:43:28] WARNING[5756]: chan_dahdi.c:18155 process_dahdi: Ignoring any changes to 'userbase' (on reload) at line 23. [Nov 11 17:43:28] WARNING[5756]: chan_dahdi.c:18155 process_dahdi:

I'm running Asterisk on a Gentoo box with the Zaptel 1.2.1 drivers. If I boot the machine without having the wcfxs module autoload, then install the module with modprobe, asterisk works just fine. If I boot the machine and autoload the wcfxs module, the module loads fine: > Jan 11 11:06:55 asterisk Zapata Telephony Interface Registered on major 196 > Jan 11 11:06:55 asterisk ACPI: PCI

Hi all, Yesterday, in an attempt to take back my phone room, I pulled everything apart as far back as the demarc and rebuilt it. In the process of putting things back together I accidentally connected my incoming lines to my FXS ports and my phones to my FXO ports. I quickly realized the mistake I made and corrected things but not before one of my FXS modules was smoked by incoming ring voltage.

Hi, I am struggling to get rid of a conflict on DELL 2800 : PCI Parity error (EB113 on the display) I am learning linux and asterisk as I go along, there might be obvious things I should know, but bear with me. >From demsg below my 2 digium cards installed are listed (no config or connections done to digium cards yet), the conflict is with the TDM400P card, without that card, in any slot, no

hi, i have problem with pass-through faxing with this scenario hylafax(iaxmodem) - iax - asterisk1 1.2.22 - sip - asterisk2 1.2.X(xen virtual) - linksys ATA i can fax to fax2mail on hylafax but after upgrade asterisk2 to 1.4 faxing is not working hylafax(iaxmodem) - iax - asterisk1 1.2.22 - sip - asterisk2 1.4.X(xen virtual) - linksys ATA configuration is same do you hava any idea what is

I'm afraid that I am at a loss here. I am new to Asterisk, and have successfully set up SIP. But I cannot get my FXS card working, and I'm not sure what else I can try. # modprobe wcfxo /lib/modules/2.4.21-37.0.1.ELsmp/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may

Hello. I have this problem. In my asterisk box, I was running debian woody with asterisk package from backports.org. Last friday I upgraded from debian to sarge and change from kernel 2.4.18-1-686 to kernel 2.6.8-1-686, rebuild zaptel kernel module and also upgrade to asterisk 1.0.2. But now asterisk won't start. Here is more info #asterisk -vvvvvvvv (last lines) [chan_zap.so] =>

Greetings all, I'm new to asterisk... Finally got two IP phones and two TDM400P's (one with four FXO modules and one with four FXS modules)... Began experimenting a couple days ago and have ran into a very aggrevating problem. My system consists of the following hardware: Abit BL7-RAID motherboard Pentium 4 1.6GHz processor 512MB SDRAM 2 TDM400P cards 2 3Com 3c905