similar to: interop problem: "Missing handling for mandatory IE 24 (cs0, Channel Identification)"

Hi, we are still trying to properly connect a Tenovis PBX to an Asterisk server (asterisk 1.2.6, libpri 1.2.2, zaptel 1.2.5, Digium Wildcard TE110P), this time with QSIG. Calling from a Tenovis phone to a SIP phone (i.e. traditional phone -> Tenovis PBX -> QSIG -> Asterisk -> SIP phone) works with the following messages: --- Don't know what to do if second ROSE component is of

Hi, I configured an asterisk box with 1 Digium Wildcard TE110P T1/E1 Card 0 I setup the jumper in e1 position. my zaptel.conf : defaultzone=it loadzone=it #gestione PRI span=1,0,0,ccs,hdb3,crc4,yellow bchan=1-15 # set this to 1-15,17-31 for E1 dchan=16 # set this to 16 for E1 bchan=17-31 # set this to 1-15,17-31 for E1 # Asterisk starts correctly, I see th 30 channels. Anyway I cannot put

Hello, I have a problem with zaptel. I hope you can help me. I installed and configure zaptel. ZAPTEL.CONF span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone = de defaultzone=de But the output of cat /proc/zaptel/* Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" (MASTER) HDB3/CCS/CRC4 RECOVERING 1 WCT1/0/1 Clear (In use) RED

I have configured /etc/asterisk/zapata.conf, but now Asterisk refuses to start: Asterisk 1.0.9, Copyright (C) 1999-2004 Digium. Written by Mark Spencer <markster@digium.com> .... [chan_zap.so] => (Zapata Telephony w/PRI) == Parsing '/etc/asterisk/zapata.conf': Found Sep 16 20:36:51 ERROR[6750]: chan_zap.c:6246 mkintf: Unable to get parameters Sep 16 20:36:51 ERROR[6750]:

Hi, I have a working Asterisk 1.2 server on kernel 2.6.22 with the OSLEC echo canceller on a Digium PRI card. I recently switched to kernel 2.6.23 with the MG2 echo canceller (nothing else changed). Each time I try to establish a call on the PRI line I get a congestion signal. in /var/log/asterisk/full: Feb 20 08:09:43 VERBOSE[10657] logger.c: -- Executing

Hi, I'm having trouble configuring and E1 link , I know the E1 is a PRI and the switchtype is 5ess. The problem is that everytime I try to dial I got and error saying that it was unable to open the zap channel . Devices are created in the /dev/zap directory and I can open them with a cat /dev/zap/1. I can also see the channels in /proc/zaptel/1. Thanks in advance [zaptel.conf]

I have configured /etc/asterisk/zapata.conf, but now Asterisk refuses to start: Aug 5 10:47:29 ERROR[1076842624]: chan_zap.c:5976 mkintf: Unable to get parameters Aug 5 10:47:29 ERROR[1076842624]: chan_zap.c:9478 setup_zap: Unable to register channel '1-15' Aug 5 10:47:29 WARNING[1076842624]: loader.c:328 ast_load_resource: chan_zap.so: load_module failed, returning -1 == Unregistered

Hi!I've a problem with asterisk,it doesn't start..it's stopped..I used the amportal start command and this is the result: SETTING FILE PERMISSIONS Permissions OK STARTING ASTERISK Asterisk ended with exit status 1 Asterisk died with code 1. Automatically restarting Asterisk. Asterisk ended with exit status 1 Asterisk died with code 1. Automatically restarting Asterisk.

Hello, I am having an issue whereby calls are being dropped randomly. I have an ISDN 30 E1 line going into a Wildcard TE220 (4th Gen). My Asterisk install is based on Trixbox 2.0. However, I have updated the source code to the following. The Asterisk release is asterisk-1.2.20. Zaptel release is zaptel-1.2.18. And libpri release is libpri-1.2.4. I have include an extract from the Asterisk log

> > Hi, Remove usecallingpres=yes busydetect=yes from your zapata.conf file. and the restart asterisk. Hopefully you will not faced drop call issues. Regards, Vidura Senadeera. Message: 3 > Date: Mon, 24 Sep 2007 12:29:40 +0100 > From: "Richard Young" <Richard.Young at intrintech.com> > Subject: [asterisk-users] Asterisk Dropping Calls > To:

I figured it out. The old system (Televantage 3 and 4 I think) has limited specifications on the T1. After setting up the system, I was able to send and recieve calls. I still have some work to do like figuring out faxing and a floating receptionist, but this is a nice start. ----------------------------------------------------Televantage T1 Requirements: Framing: D4 Superframe or Extended

I have spent some time this morning trying to add an Astribank to our current Asterisk, but it failed, so I just removed the hardware, restore the config files to the original setup and started asterisk.; I could see that no Zap channels are started so I did load chan_zap.so: pbx*CLI> module load chan_zap.so [Feb 26 10:32:18] WARNING[3809]: pbx.c:2968 ast_register_application: Already have an

Hi all, I?ve ran into a problem regarding D-channels. I have setup Asterisk (CVS-HEAD-03/21/05-16:41:57) on RH Fedora Core 3(2.6.10-1.770_FC3) I also have a digium wcte11xp card for connetivity to the PSTN(E1). When I start zttool i see that Current Alarms changes between Recovering and Blue Alarm/Recovering. I started to see these problems after i moved the digiumcard from one PCI slot to

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

I have a pair of sites tied together with a T1 line running zaptel PPP on either end. The system works, but I keep getting these messages in the kernel logs, and users are reporting connection problems (TCP timeouts, and hangs) especially under high usage. --snip-- HDLC Receiver overrun on channel WCT1/0/1 (master=WCT1/0/1) HDLC Receiver overrun on channel WCT1/0/1 (master=WCT1/0/1) HDLC

Hi Last week I installed Asterisk (release1) with digium t100p single span T1 (wct1xxp) board on Dell GX270 pc configured for PRI. Asterisk/t100p is currently the only user of the t1 line. All worked well for about a half a day, PSTN to SIP phones to non-SIP IP phones etc. Alas, since then I consistently get multitudes of blue alarms on all b-channels followed by a loss of d-channel: Aug 31

Hi, We have got a new PRI card at one of our Office locations and now I need to install the the device on a remote server. Is there any way to know if the device is loaded already. When I give " cat /proc/zaptel/* " it returns the following. # cat /proc/zaptel/* Span 1: WCT1/0 "Wildcard TE122 Card 0" (MASTER) B8ZS/ESF RED IRQ misses: 2 1 WCT1/0/1

Hello, I just bought a TE121 T1/E1 card, and now trying to install it on a 1.4.23.1 asterisk with dahdi 2.1.0.4 Actually first everything went on well and i managed to see my card on dahdi. Here's the output: #asterisk# dahdi_hardware pci:0000:04:08.0 wcte12xp+ d161:8000 Wildcard TE121 and this is the scan: -------------------------- asterisk# dahdi_scan [1] active=yes alarms=RED

Hello, Thanks to members of the list things changed on my installation (asterisk + digium E100P with of course an E1 line). Here is my zaptel.conf : - span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=fr defaultzone=fr - Output of zttool: - Alarms Span YEL/RED Digium Wildcard E100P E1/PRA Card 0 - [root@asterisk root]# head /proc/zaptel/1 Span 1: WCT1/0 "Digium

All, Alright, I've looked around the internet, the voip-info.org wiki, and browsed the contents of this mailing list. While I've found a couple of scenarios that are close to this one, I haven't found one that uses my particular card (T100P). Without further delay -- I have successfully configured internal SIP services between a Snom 200 and a Windows X-Lite client and have