similar to: No sound after loading module wcte11xp

Hi, I have installed an TE110P but forgot to change the jumper settings to E1. I don't have easy physical access to ther server at the moment so I wonder if it will be possible to run it without changing the jumper settings with a configuration like below or will it be impossible to use the card at all before I fix the jumper? I can't try it myself yet since the operator isn't ready

I have a X100P and a TE110P in my Asterisk box. I can either get the X100P or the TE110P to work, but never both. Here's my zaptel.conf span=1,0,0,d4,ami e&m=1-24 fxsls=25 When I load wcte11xp and wcfxo, I will get this error. [root at asterix etc]# modprobe wcte11xp ZT_CHANCONFIG failed on channel 25: No such device or address (6) /lib/modules/2.4.20-8/misc/wcte11xp.o: post-install

Hi, This error I got it just when I gonfigure zaptel support isdneuro 31 channels. But if I configure zaptel to support T1 and just 24 channels I have no problem. ######################################################################## #### # # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # loadzone = it span=1,1,0,ccs,hdb3,crc4 bchan=1-23 dchan=16

Folks, I installed a te110p to connect to an E-1. Ensured the jumper is on for E-1, installed the card, and got the following from the phone company: hdb3 encoding (verbally confirmed ccs) euroisdn switchtype pri signalling So I set up zaptel.conf: span=1,1,0,ccs,hdb3 bchan=1-15 unused=17-31 dchan=16 loadzone=us defaultzone=us Card tries to come up but goes into RED alarm. Occasionally cycles

Hi folks, I've already searched the mailing list but no one else seems to have my same problem. I'm using Asterisk with the following configuration: Fedora Core 4 (but I also tried Fedora 3) 1 Digium TE110P 1 TDM40B 1 HFC-S 'Cologne' bristuff 0.2.0-RC8o (zaptel 1.0.9.2) I compiled right, I can load kernel modules but when I try to unload wcte11xp module (the one

Hello List, i am trying to set up an * box with a debian 2.6.10 Kernel. the compilation of asterisk and the zaptel drivers worked almost perfectly. so i did modprobe zaptel modprobe wcte11xp (which is the correct driver for my card) ztcfg -v and this results in ZT_SPANCONFIG failed on span 1: No such device or address (6) I don?t have any ideas whats wrong. google was no help, checking sources

Hi all, I?ve ran into a problem regarding D-channels. I have setup Asterisk (CVS-HEAD-03/21/05-16:41:57) on RH Fedora Core 3(2.6.10-1.770_FC3) I also have a digium wcte11xp card for connetivity to the PSTN(E1). When I start zttool i see that Current Alarms changes between Recovering and Blue Alarm/Recovering. I started to see these problems after i moved the digiumcard from one PCI slot to

Hii all I bought te110p card. I configured zaptel.com ; span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 and zapata.conf is; switchtype=euroisdn signalling=pri_net group=1 context=nortel dchannel => 16 channel => 1-15,17-31 I receving the following error on my gentoo; May 18 13:48:44 WARNING[8755]: Ignoring canpark May 18 13:48:44 WARNING[8755]: Ignoring dchannel May 18 13:48:44

Hi everyone I have a Digium card TE110P and after plug it, turn on the computer and configure, the LEDs don't light up in spite of what Digium FAQ says about the LEDs: When will the LED's light up on my TDM400P/TE110P/TE2XXP/TE4XXP? ... The TE110P LED's will light up RED when the span is configured and kernel module is loaded. If configured correctly and a circuit or channel bank is

Hi all, I am running asterisk 1.2.18, zaptel 1.2.18, libpri 1.2.4. on a suse 10.2, running kernel 2.6.18.2-34-default. The zaptel drivers are loaded on boot via /etc/init.d/zaptel, but Asterisk is unable to start. It ends with the following message: [chan_zap.so] => (Zapata Telephony w/PRI) Jun 13 13:05:41 VERBOSE[3356] logger.c: == Parsing '/etc/asterisk/zapata.conf': Found

Hello! I discovered, that I'm unable to load ther kernel module under 2.4.28. Before that I had 2.4.26 and tryed to upgrade the kernel to 2.4.28. After restart (reboot - soft restart) I can't load the module. When I go back to 2.4.26 and try to load the module, I'm getting the same problem. Only turning off/on helps. What can I do? It's very annoying because the box is in hosting

Hi, thank you for last info. we've tried to use te110p but failed. We're quite surprised that cable wasn't included with the card as any documentation, at least on HW setup and installation, yet cable pinout for connection to PRI interfaces.... 1. We have followed instructions on your site and from Beronet guide, but card just keeps blinking and nothing happens (also no useful

hi All I need your help , for used Digium Card TE405P, for setting this Board AS E1 ISDN PRI. 1 .Current for make sure my config its rights or no I inform my configurations in Board Jumper T1/E1 is Closed is that rights or no ? for E1 i closed the Jumper. 2. I Want To seeting E1 in ASterisk/PC Back To Back To Cisco E1 AS5300 Use ISDN Signaling, my configutration :

I am having problems loading the zaphfc from bristuff and wcte11xp drivers at the same time. If I load zaphfc then all works fine. If I then load wcte11xp, the card using the zaphfc doesn't pick up calls anymore. I am using bristuff 0.2.0-RC5. Anyone else seen this problem, know of a fix, or can tell me what I am doing wrong? Thanks My zaptel.conf: # hfc-s pci a span definition # most of

I have a Digicom TE110p card installed in our exchange. I have compiled and installed libpri, zaptel and recompiled and installed asterisk. I have configured udev as I am running Fedora Core 3. The problem that I have is that when zaptel is not running everything works fine. However when I start zaptel (service start zaptel) then I can make normal calls ok but the 'Playback()'

Hi, is it possible to set a wcte11xp card to use a certain IRQ? I've tried a few things but it always shares the IRQ with eth0 even though the system has 4 spare ones. I can't set it via the BIOS. Regards Lee -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050902/9ce217db/attachment.htm

Hi, I am struggling to get rid of a conflict on DELL 2800 : PCI Parity error (EB113 on the display) I am learning linux and asterisk as I go along, there might be obvious things I should know, but bear with me. >From demsg below my 2 digium cards installed are listed (no config or connections done to digium cards yet), the conflict is with the TDM400P card, without that card, in any slot, no

Hi, I've compiled Asterisk cvs stable (few days ago) unde Suse 9.2 without any problems. We're using te110p and wcte11xp module that is autoloaded by Suse 9.2. Card goes green after reboot, but this meesages appear in logs: Mar 22 11:28:51 linux kernel: Zapata Telephony Interface Registered on major 196 Mar 22 11:28:51 linux modprobe: FATAL: Error inserting torisa

Hi there I have a TE110P card fitted in my linux box running : Linux version 2.6.9-5.ELsmp (bhcompile@decompose.build.redhat.com) (gcc version 3.4.3 20041212 (Red Hat 3.4.3-9.EL4)) #1 SMP Wed Jan 5 19:30:39 EST 2005 I followed the installation steps on digium website...no errors reported. The modules seem to have loaded...here's what lsmod shows: Module Size Used by

Hi, I plan to setup an * Server with a TE10P PRI card as E1 and a BN4S0 4 Port BRI card in one box. I tried it first with the bristuff drivers from Junghanns. The BRI card worked fine alone, but as soon as I load the zaptel driver for the TE110P the BRI card says, that the port is down. So I tried it with mISDN. But it seems that this stuff is still unstable (Asterisk refuses to start at first