similar to: TDMoIP and Asterisk

Can anyone point me to a reference or sample config for bypassing a nailed up (point to point) t1 between two PBXs with asterisk and a pair of t1 cards? Right now I have 2 Nortel norstars connected to each other via a leased line t1. I also have a solid 10mbps low latency microwave link between the 2 sites. My goal is to run an asterisk box at each end with a t1 card and Ethernet card to

Just a Question. I would like to know if TDMoE follows specifiaciones of TDMoIP RAD protocol that says that there is a compression of 16/1 when you do TDMoIP. Manuel Marin Garcia TRANSTELCO S.A. DE C.V. Campos Eliseos 9050 B4 – Cd. Juárez, Chih. 32452 - México Oficina: +52 656 692 11 09 – Fax: +52 656 692 1112 - Celular: 915 727 6141 http://www.transtelco.com.mx

Hi List, Yesterday night after a power off due to a faulty UPS my asterisk doesn't want to start anymore. Here is what I get on the CLI: Asterisk Ready. *CLI> Disconnected from Asterisk server: Bad file descriptor. Executing last minute cleanups == Destroying musiconhold processes Asterisk uncleanly ending (0). I use 1.2.7 I think on a debian sarge and cdr_pgsql too. Any ideas?

First, Something seems to be wrong with the list. I'm not the only person who has expressed seeing their messages either arrive late, or not at all. With that out of the way.. Is anyone aware of any type of failover device for PRI on asterisk? I've found the ISDNGuard, however it is currently not made in the U.S., nor does it run on U.S. power. Is anyone aware of a device that will

Hey guys. If my Asterisk box connects to the PSTN using SIP and IP over ethernet and doesn't require any authentication, what sort of a trunk would need to be created? Thanks, -- Nick e: nick.hoffman@altcall.com p: +61 7 5591 3588 f: +61 7 5591 6588 If you receive this email by mistake, please notify us and do not make any use of the email. We do not waive any privilege, confidentiality

Hi List, Is there a way to tell asterisk to only accept SIP streams from the same IP address that is used for signaling? Thanks, Jean-Michel. -- Jean-Michel Hiver - http://ykoz.net/ D?couvrez la R?union des Technologies IP & Telecom TEL: +262 (0)262 55 03 98 - RCS 434 273 330 SAINT PIERRE

Hi, I need to have some SIP extentions on remote places where the latency from my asterisk box with public ip is 1~1.5 seconds. What codec will work fine on this sceneary? I'm planning to use iLBC, is a good choice? Regards, Guillermo.

Hi List, I was wondering if anybody had tried running Asterisk inside virtualization software such as Xen. Are there known problems doing it? Cheers, Jean-Michel. -- Jean-Michel Hiver - http://ykoz.net/ D?couvrez la R?union des Technologies IP & Telecom TEL: +262 (0)262 55 03 98 - RCS 434 273 330 SAINT PIERRE

Hi, understand that the bandwidth utilized for each call is dependent on the codec used, wonder if Asterisk can monitor the total bandwidth utilized and restrict/reject new calls when the resource is insufficient to support them reliably? Regards Andy Tan -- Andy Tan andytan@fastmail.fm -- http://www.fastmail.fm - Does exactly what it says on the tin

This has been an interesting discussion for me (except for the sniping). The last post led me, out of curiosity, to this wiki entry: http://www.voip-info.org/wiki-Asterisk+TDMoE I was unaware of this feature, and it looks pretty good. I've been pondering replacing some T1's by leveraging IP capacity but of course have run up against the QoS issue. My idea was different... I

Hello all, Just a question, on asterisk box : I looking on the web , for asterisk at large , and 'asterisk future of telephonie' ... If we would like to change our OLD PABX 600 phone with 4 E1, to install a asterisk with full ip phone in SIP, Could we use 1 Box for asterisk with voicemail, zap channels and some agi script ? thanks Fabrice

Hi All, I have a SIP provider that tells me that my RTP stream uses a "20bytes payload in the g729 coded data". And they would like that we change this to 30bytes (3 frames). But maybe I'm wrong but isn't a certain payload just a standard for a codec ? And if I'm wrong, how can I change the payload for my g729 calls in Asterisk. Greetings, Attilla

Has anyone on the list used a Soekris engineering PC as a TDM - Ethernet bridge? For example something like a net4801 with a TE110p in it and then using TDMoE to get it into a bigger server where the call processing proper will occur. Anyone know if it might handle a quadspan card ok? (no transcoding, just pure PRI to TDMoE bridging). Craig

You can even set it to zero. Mine works well when in zero. The line pick up immediately :> -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Chris Stenton Sent: Thursday, February 09, 2006 6:57 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] SPA-3000 VOIP-PSTN

Has anyone every attempted to set up a mini PC to achieve much the same functionality as the fonebridge box? The sort of thing I'm imagining is a micro itx board & case in a completely solid state configuration (flash disk, maybe a psu fan but only if really required), with a TE210P (or equiv) card(s). The sole purpose of this would be to be a bridge between E1 lines and TDMoE. The

Hi, Does anyone know what is the amount of max concurrent calls that can be made in one Asterisk box? I heard that it is 256 and it doesn't depend on how good your machine is. It is the program constraint. What can I do when I need to have more calls than that. I read about connecting Asterisk boxes with IAX. Is it a good solution? Does anyone have other proposals? Cheers Andrew

Need help...I need to install a card to terminate 7 lines...I have not order the phone lines yet...I can either do analog lines 1FBs or order a fractional T1...any suggestions on what hardware would be easier to install and configure...also if I went with a T1...do I need an external CSU/DSU or anything or does it just plug into the T1 card...thanks.. -----Original Message----- From:

Greetings, We are currently testing a Sipura SPA-3000 as a gateway from our Asterisk system to a PSTN line for 911 access. We have a number of locations and want to place an SPA-3000 in each, connected to a PSTN line that will provide the correct ANI/ALI information to 911 for each location. It all works great, except for a reasonably significant (4 seconds) delay between when the SPA-3000

Is there a way somehow to implement Asterisk with Credit Card Processing (IVR system)? -- #Joseph

I want to start a community based voip network projcet and am thinkimg of using VOCAL and asterisk gateways..... my question is, has anyone bench marked asterisk vs VOCAL? is it a wise idea to use VOCAL + Asterisk or Asterisk all the way.........am expecting 1000 -> 5000 users.. your thoughts would be appreciated. _________________________________________________________________ Don't