similar to: TDM04B FXO Asterisk@Home

Just installed the new 4-port FXO card and moved two pstn lines from existing x100p cards to ports on the FXO card. All zapata.conf entries that were functional on the x100p's were copied to the new FXO channels (including callprogress=no). Observations thus far: 1. asterisk will spontanously decide a pstn call has arrived, and ring the sip phone designated in the dailplan. Verified

Hi, A week or so ago I wrote about the problems I was having using a Digium TDM04B card in a Dell PowerEdge 750 IU running Fedora Core 1. Digium steadfastly indicates their card won't work in any PowerEdge 650, 700 and 750 series machines "do (sic) to a failure in interrupt handling between the pci bus and the card." My question to the list is: for those of you using a TDM04B

Hi, I am just trying to figure out how to setup a TDM04B card for incoming/outgoing calls. I have 4 lines, which are provided as a rotary trunk group, currently hooked into a Nortel system, which asterisk will replace. I have setup a Dell 1800 (Tower) system with the TDM04B card, which seems to work. The question is how do I set it up that all 4 lines are part of a trunk group, such that

Hi, I recently got a TDM04B and after installing and getting asterisk up and running I connected a handset to one of the ports. Unfortunately I don't get a dial tone when I lift the handset. What could be the cause of this? Could someone point me in the direction of a proper config for a TDM04B? Thanks.

I already have one Digium TDM04B installed in my server working fine. I just received 2 more so I did added them to my server. When I booted again linux told me that it found new hardware I said ignore. Then I log in as usual. I did ztcfg -vv to see if it sees 12 channels now instead of 4 but it only see 4. So then I did again modprobe zaptel, then modprobe wcfxo and wcfxs hoping it would see

Hi: I had an fxo card from Digitnetworks and it was working fine on my Asterisk box. I then replaced it with TDM04B. I changed the zaptel and zapata to include the four channels. When I run ztcfg, I get configuration errors: Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04:

Hello All, I got my TDM04B card installed and configured. Everything works fine I can receive calls and route to appropriate extensions. The only problem I am facing is Slowness. When I dial the PSTN number which is connected to Zap 1-1 after two ring it answers and then run the AGI script. What I did was assign it to a specific extension. So all inbound call on that PSTN number should

Hi, I just received in the mail my TDM04B card and put it in the computer, now the computer won't even show the video card bios or the post screen. From the digium website I could not find any specific requirements for the pci card, like 32 or 64 bit slot. The motherboard for the computer I put it in is an Asus A7V333 with PCI 2.2 compliant slots. I am thinking that maybe I just got a dud

Hi and thank you. I am a beginer trying to install my first TDM04B. I am able to receive call with the card using: [incoming] exten => s,1,Dial(SIP/robgol,20,tr) on my extensions but, with [outgoing] exten => _0X.,1,Zap/1/${EXTEN} I cant send them out. I am getting the following error: Mar 26 23:37:07 WARNING[5189]: pbx.c:1291 pbx_extension_helper: No application

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: VoIP.gif Type: image/gif Size: 17666 bytes Desc: 1197705770-VoIP.gif Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20060213/7ca1c4ac/VoIP.gif

Hello all, I am having a serious problem installing my * with a TDM04B. I made everything work, call are coming in and going out including using a GSM Box in channel Zap/2-1. I did setup voicemail like this on extensions.conf: [incoming] exten => s,1,Dial(SIP/2246,20) exten => s,2,Wait,2 exten => s,3,Voicemail(u${ME}) exten => s,4,Hangup exten => s,102,Wait,2 exten =>

Hi, Some weird problem (or I'm too sleepy) happens with a tdm04B revision G (4fxo) Steps: modprobe zaptel modprobe wctdm ztcfg -vv /etc/zaptel.conf fxsls=1-4 # TDM04B defaultzone=us loadzone=us /etc/asterisk/zapata.conf signalling=fxs_ls group=1 context=incoming channel => 1-4 modprobe zaptel and wctdm load fine, however ztcfg -vv shows: 0 channels configured Im using centos 4.4 with

Hi all, I've struggled for several days trying to get a Digium TDM04B 4-port wxfco card working on a Dell 1U PowerEdge 750 machine running Fedora Core 1. I finally got a call back from Digium who indicated that there is a fundamental conflict between the card and the PowerEdge having to do with PCI interrupts. Asterisk version is stable v1-0 12/29/04. The symptoms of the problem were as

I am searching for a way to add a 2 second delay before calling out with Dial(). Sometimes I get the message "you must first dial a 1 to place this call". I presume the phone company is missing the first digit pulsed out sometimes. How do I put a 2 second delay after coming offhook and before dialing the digits? Thanks, jerry

I have a client who wants a Meetme box with 12 FXO ports, to connect to Analogue lines coming from an Ericsson PBX. It looks like I could do this with four different hardware configurations: a) three TDM04B cards (based on TDM400P) b) one TDM04B and one TDM808B c) one TDM804B (or TDM854B?) and one TDP808B d) one TDM2403B (half filled TDM2400P) Apart from considerations of cost and PCI slot

I have installed Digium TDM04B with the latest CVS. However I have encountered following problems: 1. When it dials out, many times the digits are not properly recognized by telco as I hear the announcement "please check the number and dial again" although I see on the screen that the dialed number is correct. 2. When the call is forwarded outside, with something like exten =>

Hi, After days tinkering with this digium card (TDM04B), I notice that this card has a slow response in detecting ring signal from pstn and hanging up when the call is over. The delay can consume up to several seconds... Is this normal? Best regards, Stevanus

Hello I am struggling to get my TDM04B working. Just to rule out a hardware problem how can I check that the hardware works? How can I then check that the drivers are loaded correctly? Angus -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050620/470458c6/attachment.htm

Hi; Can I use two TDM04B in one asterisk box with asterisk@home? Thank You Onemli not : Bu e-mail iletisi, sadece adreste belirtilen kisi veya kurulusun kullanimini hedeflemekte olup, mesajda yer alan bilgiler kisiye ozel ve gizli olabilir, yasalar ya da anlasmalar geregi ucuncu kisiler ile paylasilmasi m?mk?n olmayabilir. Mesaji alan kisi, mesajin g?nderilmek istendigi kisi veya kurulus

I just install a Digium TDM04B card. I created 4 separate Zap channels and one outbound routing containing zap channels from 1 to 4. If a phone line is plug in Zap/1 then works fine, but if I unplug phone line from Zap/1 (simulating fail) the system keep dialing out on Zap/1, even with no dial tone; Only if Zap/1 is busy it will use Zap/2. There is any work around or different setting to avoid