similar to: DID over analog?

Hello everyone, I'm hoping someone can help me with this. I have a business customer in the U.S. (Michigan, AT&T Territory). I need to get 4 trunks into an asterisk Box. My intention is to use an Eicon Diva Server card with 2 BRI Circuits. The reason for this is that the business needs DID's on the trunks (20 of them). A full or fractional PRI is overboard for them, as they will

Hi Everybody, Has anybody tried the above (or indeed any other 4XBRI cards) successfully with Asterisk. As far as I can see the above mentioned card is an active ISDN card but supported by it's own I4L driver. This leads to interesting questions particularly regarding echo cancellations (which usually doesn't work on the cheap passive cards with one exception as far as I can see).

Hi! I have some (short) question about the Eicon DIVA (V-)4BRI cards I want to have (short) answered before buying the DIVA card. I know there are several Eicon guys active on the list, thus I ask on the list instead of directly to Eicon so that all other will benefit as well. 1. Do Eicon DIVA (V-)4BRI cards support TE and NT mode? 2. Can the clock (master/slave) be configured independent

Hi, I have to set up an Asterisk with an 4-port BRI card. Hylafax should send and receive fax. Will this work reliable? Any recommandations for an 4-port BRI card? Other alternatives except analog fax units? thanks for your help best regards Thomas

I'm looking to use Asterisk with Verizon ISDN centex service in the US. I'd be connecting to an NT1 so I'd need an S/T interface. Users would have SIP phones registered with Asterisk and sharing the ISDN lines. The only PCI ISDN card that will support ISDN signalling in the US seems to be the Eicon Diva Server cards. These are hard to find and very expensive ($2500 for the Quad

Hi I've got a dell 2550 with an Eicon Diva server PRI card plugged into it. I can call out using the acopy2 test utility. I'm having trouble with asterisk making calls however... my capi.conf and modules.conf looks correct by the wiki instructions - does anyone have any advice on where to look ? I can attach conf files etc. if needed. Asterisk says it has 30 capi channels available,

Hi everyone, I have Asterisk SVN-trunk-r7498 running for a few months and I'm quite happy with it. However, I am experiencing a quality issue with my AVM Fritz!card PCI which is used with chan_capi. When somebody calls me on this line he hears a lot of noise and I hear "scratches" and "plops". It is very annoying. Below is is my /etc/asterisk/capi.conf I've tried to

Hi; I've got an AAH installation where a customer wants to install an active Eicon DIVA BRI card. AAH is built on Centos 3.5 which is currently at kernel 2.4.21.37. Support for Eicon active cards is built-in. I've debugged and run the A@H install-Eicondiva script but when I try to run divactrl load -c 1 -f ETSI -Debug I get a response : A: can't get card type for DIVA adapter

Hi, I'm looking for an interface card for termination of Euro-ISDN2 (BRI) lines. That is ISDN lines from the telco into my Asterisk box. Any recommendations, good/bad expiriences ? At present I'm looking at cards from BeroNet and Junghanns. Cheers, John Faroese Telecom

Hello All, Has anyone configured bri to answer for only one msn? In essence, when the primary is busy I want to have channel 2 ring. I am using an eicon diva server bri I know I saw it in the windows interface, but don't see it in the linux setup. Regards, Greg

I have read most of Eicons information on Q.SIG, and I am able to load the Q.SIG protocol (instead of ETSI for example). No strange logging in divacrtl mlog. But how do I tell Asterisk to understand Q.SIG? My PBX is configured for QSIG, but I cannot see anything on my trace when trying to make a call via the S0(Q.SIG) Janne > -----Ursprungligt meddelande----- > Fr?n:

Heya Mark (and others), Here's an update on my adventures while trying to debug the Zaptel-related panics, as discussed on this list a while back. While debugging the problem, I completely swapped the machine for an entirely different model (Supermicro dual Xeon 2.4GHz with 2Gb of RAM), put the cards in, recompiled * + Zaptel and administered my stress-test. The machine stayed up in excess

Hi, I would like to set up a high density FAX/PBX server, am looking at using Eicon Diva E1 card with Asterisk and Hylafax sharing channels, is this possible. I know Extensions can be reserved for voice OR fax with the combination of chan_capi used for * voice, capi4hylafax on fax but then channels must be dedicated rather than shared ie. would like to be able to answer voice/fax on same DID.

Hello, I need to connect one diva server 4bri to a portuguese BRI interface. The operator (PT) said that this bri is in point-to-multipoint mode (S0). Previously one PBX has connected to that interface. The asterisk and diva drivers are working ok but i cannot communicate to outside via this bri. Xlite gives me the message: "call failed: declined". Anyone have experience with this

Hello Everyone, I am once again wondering about EICON. I have had no success with the Diva Pro or Diva Pro PCI, so my question is, does anyone use an Eicon Server BRI card on Asterisk? Or would I be better off trying to get a split PRI? Regards, Greg

Hey all, It such a shame that BRI technology is such a flop in the USA. For a small office such as mine it would be a great product. So her goes my question.... What is a known asterisk working BRI card that will operate in the USA. I need to weigh price/quality. I need to do DID/DDI (or what ever you want to call it). Asterisk will do everything else I need. The ILEC has at the other

I am trying to use chan_capi with an Eicon Diva Server BRI. I installed the Eicon drivers from source including CAPU and I can use the board correcly using tty_test and minicom over /dev/ttyds01 or /dev/ttyds01. I need to insmod capi ( why? it is not written anywhere) and then capiinfo shows me all board parameters, but I have to break it otherwise capiinfo doesn't exit at all, but I don't

Hey guys This is probably for Armin, but I thought maybe someone else might have something I could try. I'm having a problem with one of my Eicon Diva V-4BRI cards and I'm trying to work out if its a driver configuration error, card failure or telco problem: I have an Asterisk box running -- the Eicon drivers see all four ports on my card, capi.conf is configured with all four ports

asterisk-users-request@lists.digium.com is believed to have said: >chan_capi does not set the NT-mode. Your cards driver need to do that. >E.g. for Eicon DIVA Server cards, you just set the '-x' option with divactrl >or set NT-mode in the config wizard. >chan_capi does not (need) to know anything about what protocol the card is >doing. CAPI is independent here. Ok.

Hi (Armin)! Does someone knows how to identify the type of the card? The delivery note says it is a V-4BRI-8M, whereas lspci reports a 4BRI-8M. What is it really? Are there any Eicon tools to identify the card type? thanks klaus 0000:0a:03.0 Network controller: Eicon Networks Corporation Diva Server 4BRI-8M Rev 2 (rev 01) Subsystem: Eicon Networks Corporation Diva Server 4BRI-8M Rev