similar to: Call Rules

Hi all, I've recentrly starting to play around with *, when all I wanted is to configure an fritz ISDN card with A@H. Currently I'm stuck at the phase of what do I do with capi after everything is installed. I'm trying to understand how to setup incoming and outgoing calls at A@H since I'm getting a bit lost with the default dial plan. It seems that * answers but disconnect

Hi, I have some problem to get this setup working. I have a CAC Channel Banl I, with FXO and an Asterisk box ( I am using Asterisk@Home 1.2) and I have a TE110p installed in this box. What I want to do is, just to be able to dial one of those lines that already are connected to the channel bank, and transfer that call through TE110p and Asterisk to a user agent somewhere through Internet.

Hi all, I have some problem to send a FAX to a given number. I use asterisk 1.2.18, on a openSUSE 10.2, i586 host. The FAX is sent out via an ISDN PRI interface, I'm in Germany, and the destination FAX devices are in Germany too, but in different areas, so I have to use a city prefix. I did set the pri device in debug mode, below are two calls, to two different FAX numbers, the first is

I have an X100P clone hocked up to an analog line of my PRI. I can use it to dial out. but when I call the extension it answers and says "GOODBY" I have a Livevoip DID which successfuly rings to ext 202 I am using asterisk@home and through the AMP inface the line should ring to ext 202 Below are Asterisk Messages, Extensions.conf and Extensions_additional.conf Extensions.conf

Hi, I'm a newbie on * trying to setup an HFC card. I'm locked for many days getting the all-circuits-busy. And no idea what else to look for/how to diagnose. I'm in Spain, I've tried changing many parameters on zapata/zaptelcong with no luck, also NT & TE modes (honsetly, I've no idea what is). Any clue will be very much appreciated! I've installed *@home on my RH9,

I'm having trouble getting outbound calls going with aah 1.3 and a tdm400p w/ 4 FXO. Incoming calls work fine, outbound I get this: -- Executing SetVar("SIP/231-af2b", "OUTNUM=6643955") in new stack -- Executing Cut("SIP/231-af2b", "custom=OUT_1|:|1") in new stack -- Executing GotoIf("SIP/231-af2b", "0?19") in new stack

Just installed V 0.4 of asterisk@home Programmed up 3 sip budgetone extensions, they call call each other fine. Tried to dial '9' for an outside line through an X100P to a packet8 ATA but got 'all circuits are busy now'. Here is the console output. == Spawn extension (from-internal, h, 1) exited non-zero on 'SIP/30-8d25' -- Executing

Hi, I have this setup: E1 PRI PSTN -- Asterisk -- Alcatel PBX - analog phones Can someone tell me what's wrong with this call initiating from an analog phone connected to Alcatel PBX? It dies with NOANSWER but all works if I call other destination numbers. Dialplan is a simple Dial(zap/g1/0984465691) statement. At the end you'll find also zapata.conf.

Hi All, I have searched the various post and not able to find the solution. I am using Asterisk 1.4.21.2 for outgoing calls. Earlier i used ZAP trunk and it works fine. Now i need to move to SIP trunk and configured the same. When i try from softphone i got error as "Call rejected" and in the asterisk i got error as

hi i've configured a TE205P on asterisk at home this is my zaptel.conf span=1,0,0,ccs,hdb3,crc4,yellow span=2,0,0,ccs,hdb3,crc4,yellow bchan = 1-15, 17-31 dchan = 16 bchan = 32-46,48-62 dchan = 47 loadzone = it defaultzone = it and my zapata.conf signalling=pri_cpe ; pri_cpe = PRI slave ; pri_net = PRI master switchtype=national usecallerid=yes hidecallerid=no callwaiting=yes

Hi all, I'm new in asterisk and I got to set up a dundi config for my work. I have 2 PBX for the test, the two PBX are in the same local network PBX A : 192.168.199.23 PBX B : 192.168.199.21 my config files : (on PBX B , the config files on PBX A looks like it) /etc/asterisk/dundi.conf [general] bind=192.168.199.21 port=4520 cachetime=5 ttl=32 autokill=yes entityid=00:30:18:4C:33:53

Nik, Just curious - what is your telco setup? Do you have PRI with the specified D channels? You need to make sure that your telco is set up to have the D channels on 16 and 47. When you first start Asterisk, or when you log on to the CLI, do you ever see messages stating the B channels are successfully started? Let us know. -MC -----Original Message----- From:

I have a problem calling a certain number from our PRI line. Calling the number from a separate PSTN phone works fine. The remote number seems to have some funny call redivert setup, when you call it, it answers immediately, makes some kind of beep and then starts to ring. Our PRI is in the UK from Telewest/NTL/Virgin Media and most outgoing calls work without a problem. The server is

Greetings *`s, I am manually creating call files and dropping them into /var/spool/asterisk/outgoing to be picked up by *. Presently, when I use local/internal parameters using SIP it works..ie I make an internal call from device to device. However, when I try dial an outside number which I have set up in a custom conf file, it bombs out with the following message :

Hello, This is my first asterisk installation, and having read up on the documentation, and trying several tutorials i'm unable to get my outbound route working. I'm certain it's an issue with my configuration and my inexperience with asterisk. So i have my POTS phone connected to my digium card, and when i make a call, I receive the "cannot be completed as dialed" message.

Hi, We are using VOIP-SIP gateway to route outbound PSTN calls. Recently, I am getting == No one is available to answer at this time message, after making 5 SIP attempts (Retransmitting #5 (no NAT):), and the calls are going out through alternate Zap-trunk. I do not see any hit (sip-debug traffic) on the voip-gateway for the failed calls. Strange thing is that this is happening randomly,

Hello, I'm running Asterisk@home 2.5 asterisk 1.2.4 zapatel 1.2.2 libpri 1.2.2 on a Dell Poweredge 2850 (1 CPU) with a TE210P I have 2 t1 circuits using NFAS with dchan on 24 and no backup dchan. I am able to receive inbound calls on all channels and can only make outbound calls on channels 25-48. Attempting to make an outbound call on channels 1-23 results in congestion.

hi,all when i send a call to other server use SIP trunk, i got this below, <--- SIP read from 222.46.18.52:5060 ---> SIP/2.0 403 Forbidden what's rong with is? > Asterisk 1.4.21.2, Copyright (C) 1999 - 2008 Digium, Inc. and others. > Created by Mark Spencer <markster at digium.com> > Asterisk comes with ABSOLUTELY NO WARRANTY; type 'core show warranty' for

I have posted my problem on the link below, but didn't get any answer. I am hoping someone here can help me with this issue. Here's my problem: I am using H323 to talk between Asterisk and Avaya IP Office 500. For some strange reason, when we are talking on a VoIP call, we get disconnected after 10+ minutes. We have two other Elastix box, but none of them are getting disconnected. From

Hi, I am trying to dial # or *411, in order to understand what the * box should answer me. In both cases, I only ear "Good-Bye" (italian , "arrivederci") dialing # -- Executing Wait("SIP/555-a2e5", "1") in new stack -- Executing AGI("SIP/555-a2e5", "directory||ext-local|lo") in new stack -- Launched AGI quitScript