similar to: TDM02B card difficulties

I am trying to reconfigure an asterisk box that was using an HFC-S card with bristuff but is now using 2 analog lines therefore I want to use the TDM02B to connect to two POTS lines. The TDM02B has 2 red modules. I have this in /etc/zaptel.conf loadzone=nl defaultzone=nl fxsks=1-2 I have /etc/asterisk/zapata.conf signalling=fxs_ks echocancel=yes echocancelwhenbridged=yes echotraining=400

Hi all, The firmware I used is pa168s_iax2_us_151011.bin. My problem is the handset dial before I finished key in all the numbers, no matter how fast I managed to press the keys. It appeared it always dialed immediately, for example "011862", when I actually ment to dial 0118620xxxxxxxx. Thus left the remaining numbers "0xxxxxxxx" unsent. The handset had its dial plan

Hi everyone, I just installed a TDM02B and surprisingly, I had really no problems except one. If I place an outbound call on the Zap line (Zap/3), everything works fine except when the called party hangups before I do. I do get congestion, but that is expected. However, when I try to make another outbound call using that Zap line, the CLI shows that the call is being dialed, but nothing

As best i could figure it out, I've installed dahdi and rc4. My TDM400P doesn't answer fxo or fxs. /etc/dahdi/system.conf: loadzone = us defaultzone=us fxoks=1,2 fxsks=4 /etc/asterisk/chan_dahdi.conf: [house-phones] context=internal ; Uses the [internal] context in extensions.conf signalling=fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel dahdichan => 1 ;

Hello list, I have prepared a small recipe on how to compile Asterisk 1.2 beta 1 with a TDM400 card and H.323. You can find it at http://www.oinko.net/astrecipes/index.php?n=102 Any comment / suggestion / modification /bugfix is welcome! I was wondering: is there any way to build a version of Bristuff for 1.2 beta 1? Bye for now, l. -- Loway Research - Home of QueueMetrics

Hi list! Do anybody has success histories about using the Beronet app_saynumber application? For those that are hearing about for the first time, it?s a piece of software that enables the use of another language in say_number commands in asterisk dialplan or AGI scripts. Link to download: http://www.beronet.com/download/app_saynumber-beta-rc1.tar.gz I?m trying to compile it in

/bin/sh: -c: line 0: syntax error near unexpected token `;' /bin/sh: -c: line 0: `if [ -n "" ]; then if [ -f ]; then mv -f .bak ; fi; cat .bak | grep -v "alias char-major-250" | grep -v "post-install torisa /sbin/ztcfg" | grep -v "post-install wcfxsusb /sbin/ztcfg" | grep -v "alias wctdm" | grep -v "post-install wctdm

I finally got Solaris to successfully make asterisk, using these instructions: http://sunfreeware.com/programlistsparc10.html#gcc33 Now though, when I issue the make install, I get this error: mkdir -p /var/opt/asterisk/spool/system mkdir -p /var/opt/asterisk/spool/tmp mkdir -p /var/opt/asterisk/spool/meetme install -m 755 asterisk /opt/asterisk/usr/sbin/ install: asterisk was not found

Has anyone had any echo issues with the Digium TDM02B FXO card? I purchased a clone wildcard on E-Bay for $8.00 and have had horrible echo issues.... I'm assuming it is because of impedance issues? Just wondered what people's takes were on the TDM02B FXO and echo?

Hi, I got a card from Digium TDM with 2 FXO modules (red ones). There is a problem that has me quite upset and is that asterisk always detect tones repeated two, three or more times. i mean, if i press 123 on my phone. asterisk detects somethin like: 1112233333 or 1111112333 or things like that. How can I fix it? I tried to change the volume level but this happens even if is set to 0. Why this

Hello all, I instaled an asterisk 1.2.X, with two lines FXO and two snom 3200 phones, on an amd_64 processor. All goes well, the voice is clear on the remote side but in the Voip side, where the Snom 320 is placed, I hear my voice, but don't in the line, the echo is on the phone. I just play with zapata gain values and with the Snom mic volume, but the echos does not disapperars. the phone is

Hi All, I have the problem setting up TDM22B card. Steps what I have followed are: [1] compiled zaptel-1.0.9.2 & installed the same. [2] modprobe wcfxo /lib/modules/2.4.20-8/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg

Hello I am (attempting) to run the astlinux version of Asterisk on a VIA embedded platform. I have a TDM04B and pretty sure zaptel.conf and zapata.conf setup OK. They worked fine with same card in traditional PC anyway. I think need the module wcfxs for a Digium TDM04B card. Is this module not part of astlinux? Do I need to download it? Or is it in opt? I see wctdm - but think that is

Hi, I have a TDM400P running with only one FXO port running on a VIA EPIA MS10000 (1Ghz Via Eden). When I run zttest from Zaptel 1.2.1 it hang and when I interrupt it with Ctrl-C that is the result: ?anyone have some idea about why isn't working? Some additional info: # /usr/src/zaptel/zttest -v Opened pseudo zap interface, measuring accuracy... --- Results after 0 passes --- Best:

Hi all, I have been looking at the code for both the zaptel driver (wctdm.c/wcfxs.c) and the asterisk channel driver (chan_zap.c) trying to figure out how much of this that has been implemented. So far I can see that the current stable 1.0.9.1 zaptel driver don't have the SETPOLARITY ioctl that would be required to properly signal the Swedish/Dutch CLIP, but the 1.2 beta1 has this

Hi, I would like to use a digum card to call an external number through my PSTN. I think that I have a problem in the configuration. Asterisk returns me app_dial.c:764 dial_exec: Unable to create channel of type 'Zap' I use Fedora core 3. I installed libpri, zaptel and asterisk. I plugged my line on the FXS module (green part). I make modprobe zaptel && modprobe wctdm without

The first beta of Asterisk 1.2.0 has been released! It is available from the ftp.digium.com FTP servers, as well as the Digium CVS servers (under the 'v1-2-0-beta1' tag). This version of Asterisk represents a significant improvement in features, stability and compatibility over the 1.0.x releases. Some of the major new (or upgraded) features include: * Asterisk Realtime Architecture

Hi, I have just put in a tdm400p with 4 fxo modules and am trying to dial out from x-lite to dial my mobile phone just to test. The output in the asterisk console is like this Executing Goto("SIP/2002-239b", "mobile|61400039953|1") in new stack -- Goto (mobile,61400039953,1) -- Executing Goto("SIP/2002-239b", "localcall|61400039953|1") in new

I've got the latest zaptel and cvs asterisk software loaded on my phone server running FC3. And yes, It's fully updated and udev is setup correctly. I've got a TDM400P with one FXS and one FXO module installed. When I load zaptel and wctdm and run ztcfg -vvv, I get this: [root@asterisk ~]# ztcfg -vvv ZT_CHANCONFIG failed on channel 1: No such device or address (6) Zaptel

Hi R-friends, Attached is the SAS XPORT file that I have imported into R using following code library(foreign) mydata<-read.xport("C:\\ctf.xpt") print(mydata) I am trying to maximize logL in order to find Maximum Likelihood Estimate (MLE) of 5 parameters (alpha1, beta1, alpha2, beta2, p) using NLM function in R as follows. # Defining Log likelihood - In the function it is noted as