similar to: TE411P and TE406P stability

Hi Guys, I need your recommendation which card to buy?The TE411P or TE406P do they have any difference?I check their brochures they are differ only when it comes to PCI slot voltages.Which card best to use?Btw,Il be using supermicro board with 3.3V and 5.5V?Will il be experiencing problem during the implementation later on if i choose the wrong PCI voltage options?Will it depends on

I too had a server room fry and need to replace h/w. So what specific Dell servers did/do you deploy? Where is the link w/Digium/s Dell caveats? I'm using the Digium TDM400 card w/* > Date: Thu, 13 Apr 2006 19:19:13 -0500 (CDT) > From: Aaron Daniel <amdtech@shsu.edu> > Subject: Re: [Asterisk-Users] Digium cards, so disappointing ! > To: Asterisk Users Mailing List -

I am experimenting with an asterisk setup in my office. The last bit I have to test is working with analog lines. I have TE411p digium card, with an ISDN line plugged into the first, a channel bank plugged into the second port, and the last two ports empty. I have the following setup in my zaptel.conf: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 span=2,0,0,d4,ami fxsks=25 And in zapata.conf, I

I currently have Asterisk deployed in my office with a TE411P. On the first port of this card is a T1 from the telco setup for D4 AMI. Unfortunately, I'm not receiving caller ID on inbound calls from this line. The caller ID information is arriving in the form *ANI*DNIS*. In zapata.conf, I have signalling set to em_w. The DNIS always arrives correctly, but I'm never receiving the ANI

I am having a problem with asterisk not being stable enough for production use. I have two cards, the digium TE406P, and the TE410P. The TE410P is the primary card that I am using but I would like to move to the TE406P for the echo cancellation and more flexibility of PCI slots available. General config info: 3 PRIs, configured as such: span=1,2,0,esf,b8zs span=2,0,0,esf,b8zs

I just implemented a system using a TE411P hardware echo cancellation card. Per Digium, I setup zaptel.conf, and zapata.conf the same way as I always have. To my surprise calls out to the PSTN had a terrible echo. 1 - 2 second delay, and quite clear. The echo was so bad that I had to remove the hardware echo cancellation module from the card. We are only using the 1st span of this card right

Hi all, I am having problems detecting fax on a client site using the TE406P (card with echo cancellation module) under 1.2 and was wondering if anybody was having or has had similar problems? Currently I can not get the system to detect fax for love nor money, in zapata.conf the relevant entries are set to: faxdetect=outgoing and I have a fax extension in the necessary context. I have taken

Hi, My configuration is pri----*(te405p)---iaxclient. My * version is 1.0.7 running on tyan dual opteron board. I have several problems. 1) inbound echo For outbound call(iaxclient-->pri), there is almost no echo. But for inbound(pri-->iaxclient), I can hear distinct echo. Can Sangoma a104 or digium te406p help this problem? 2)Today i received te406p. I know T1/E1 jumper. But how can i

Hi, I've installed an TE406p, asterisk1.2 on tyan opteron board. After installation there is no interrupts from TE406p. Is this board stable? Should i change * version to 1.0.9? Regards, Jason __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

Hello, Now that we've had our new Digium TE406P card in production for 4 days we have discovered audio drop problems that happen randomly across all channels. Here's more about our setup: P4-3.2GHz 2GB ram Slackware Linux 10.1 with custom kernel 2.4.29 Asterisk 1.2beta1 Digium TE406P quad T1 card with the following attached: - 2 x RBS D4/AMI 24 channel T1s - 1 x RBS B8ZS/ESF 24 channel

I just wanted to post here and let everyone know that the TE406P (quadspan T1/E1 with hardware echo can) kicks some serious ass. We've been running a PRI now for over a year with Asterisk (every single call in and out is through two Asterisk boxes, including faxes) and while the software based echo cancellation is more than adequate, we'd get the occassional "edgy" echo and

Hi, I found E400P quad PRI card quite cheap (749USD): http://www.govarion.com/product_info.php?cPath=1&products_id=2&osCsid=68cdd6e3d08754 in comparison to te410p (approx 1500 USD ) http://www.digium.com/index.php?menu=product_detail&category=hardware&product=TE410P Now newer generation with HW echo canceling emerged (te411p). I'm not sure in what things those two cards

I received a TE406P card from Digium yesterday and have done several tests on it and cannot get it working reliably with any Stable release or even CVS v1.0. What are other people that are using the TE406P card using for an Asterisk version? I tried 1.2.0 beta1 and it seemed to function well except for an unrelated issue with the beta release where the manager interface chokes under

Guys, I'm trying to configure a TE406P with MFC/R2. here goes my zaptel.conf: span=1,0,0,ccs,hdb3,crc4 cas=1-15:1101 dchan=16 cas=17-31:1101 span=2,0,0,ccs,hdb3,crc4 cas=32-46:1101 dchan=47 cas=48-62:1101 The first strange behavior is that the: zap show status shows this: Description Alarms IRQ bpviol CRC4 T4XXP (PCI) Card 0 Span 1

Hi all, 1. Just bought a new TE411P and about to install it replacing the existing TE410P. I am assuming I need to set echocancel=no and echocancelwhenbridged=no now that it will be done in hardware, correct? 2. Is there any way to monitor hardware echo cancellation to ensure it is working (apart from being on a call)? 3. The Digium webite says "By supporting 16ms with 128 channels or

hi! anyone please recommend/guide me of purchasing a resonably high performance server system regarding processor(s) & motherboard (+ other compulsary peripherals i.e. VGA, Soundcard). Mentioning up-to-date vendor+model will be more helping I've to use Digium TE411p Quad E1 card signalling on the E1 is SS7 no. of simultaneouse calls is 100+ regards -------------- next part

Hi, I just read a pressrelease from VON that Digium will soon be releaseing a couple of new cards. What got me interested was: "The TE420P and TE415P support 128ms of G.168 (2002)-compliant echo cancellation across their entire 128 channels." Does anyone know when thease will be released and what they will cost when released? Thanks!

Hi all, I replaced a TE410P Rev C 1st Generation Firmware with a TE411P without any cfg changes (zaptel/zapata). As a result Asterisk crashes on outbound from PRI4 going to PRI1 calls: Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a UA, but i'm in state 1 Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a UA, but i'm in state 1

Hi, Does anyone know if it's possible to have 1 port of TE406P to provide T1 PRI to other VoIP gateways? I am trying to provide T1 PRI to one of our old Clarent gateways to integrate it to Asterisk. Can anyone help? Thank you. Andy

So, I'm still having this problem with outbound calls not working when using a channel bank. I've purchased a Rhino FXO channel bank from VoIPSupply.com to make sure it wasn't an equipment problem. I am using a Digium TE411P card, and have simplified it down to just 1 port plugged into the channel bank, with just 1 analog line plugged in. If I place an inbound call on the line, it