similar to: Wildcard TE110P

Hello; I would like to know what's new in motherboard compatible with a Digium card like: Wildcard TE410P or Wildcard TE110P. Thanks every body for helping me!!! :-) //vador

Hello, Digium support kindly proposed to ship a TE120P card to help resolve the issue. I plugged in the card, and introduced the loopback plug. I cleared the red alarm for a while and then i started seeing alarm switching from Yel/Recovering to Blue/Rec with a lot of IRQ Misses. I call Digium that assisted us, and we noticed IRQ sharing with the VGA adapter and the Ethernet port. I changed

Fedora Core 6 regards, Pablo. On Thu, Mar 08, 2007 at 05:01:15PM -0800, Jose Bertuzzi wrote: > Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: > ??? Alarms Span ??? OK Digium

Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: ??? Alarms Span ??? OK Digium Wildcard TE110P T1/E1 Card 0 ??? OK Digium Wildcard TE110P

Hi I have one question, somebody can tell me if the card TE110P work in mexico, and maybe can tell me the config. Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050923/9dedf2bc/attachment.htm

Hey there, What recommendations does anybody have as to motherboards known to work well with the Digium TE110P T1 interface cards and the TDM400P analog POTS interface cards? We currently make use of the TE110P for our T1 (esf w/ b8zs - not a PRI) and have experienced many issues caused by our PBX's motherboard. Additionally, we built a server to become our new PBX, but that machine runs

I'm not 'overly' new to asterisk, but I am very new to the Digium card / Telco aspect of it. I was able to get a TE110p card, installed.. and hooked a t1 up to it. I'm using zttool to just look at 'some' output. Here is what it looks like when I just load it up: Current Alarms: No alarms. ? ? ? ? Sync Source:

Try to use 2.6.10 kernel not 2.6.12.3 kernel Coz I got some problems with the kernel 2.6.12, I had the same Digium Wildcard TE110P, Good luck ________________________________ Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di Robert Christian Inviato: marted? 26 luglio 2005 19.13 A: asterisk-users@lists.digium.com Oggetto:

Hi everyone I have a Digium card TE110P and after plug it, turn on the computer and configure, the LEDs don't light up in spite of what Digium FAQ says about the LEDs: When will the LED's light up on my TDM400P/TE110P/TE2XXP/TE4XXP? ... The TE110P LED's will light up RED when the span is configured and kernel module is loaded. If configured correctly and a circuit or channel bank is

Hi All I have a TE110P card connected to a PRI line. In my zaptel.conf I have: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 loadzone = us defaultzone=us and my zapata.conf is: [channels] context=inbound-pri switchtype = national pridialplan=unknown ;pridialplan=international signalling = pri_cpe callerid=asreceived busydetect=no usecallerid=yes hidecallerid=no callwaiting=no callwaitingcallerid=no

Hello All, I have got my TE110P working at the hardware level, turned out to be a dodgy cable causing the Yellow errors in zttool. However, now I am getting yellow errors in asterisk, but zttool shows nothing out of the ordinary. here is my current config, and some asterisk console errors, any suggestions most welcome. zaptel.conf span=1,1,0,ccs,hdb3 bchan=1-15 dchan=16 bchan=17-31

Thanks for reading this. I've been pulling hair for days trying to resolve this, and any help someone can give me would be very much appreciated. I have an Asterisk box that is basically a P4-3GHz, a Digium-recommended SuperMicro X5SSE-GM motherboard, 2GB RAM, 250GB IDE hard-drive with UDMA, a SoundBlaster Live! 24 sound card, a Digium Wildcard TE110P, and a Digium Wildcard TDM400P with 4

Helo, I have a troubles getting to stable work of Digium TE110P card (mailed some time earlier in the list) - I can't get 100% pseudo zap interface accuracy (zttest), so getting HDLC aborts and call drops. I tried number motherboards, hardware and software configs according to info in wiki, thisl list and number of websites - no luck. So I ask everyboby who successfully use Digium TE110P card

Helo, I have problem with Digium TE110P connected to CISCO 3640 (port on NM-HDV-2E1-60) wth PRI E1 link. I use CISCO now for testing but when I tried with real PBX problem was exactly same. I have this messages in Asterisk conole and log sometimes: NOTICE[1115] chan_zap.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Usually 2-5 such messages in series, can be repeated after 10

I am trying to use TE110p card for Euro ISDN with Ericsson AMS switch. I consistently get one of the following errors: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 or PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 My zaptel.conf file: -------------------------------- span=1,0,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone=us defaultzone=us

Hi! I'm trying to setup a Wildcard TE110P with a PRI in The Netherlands. I get a Red Alarm on the line. Is there any way of debugging this? I've tried some configs that should work but without success. Is there any way of telling if the cabling is correct or what else the problem could be? Thanks!! Remco

Hi!, this issue makes me crazy. I read a lot of docs, also * mailling list and I try a lot of things without success. Any help will be appreciated. Here is the info: Hardware: -------------------------------------------- Supermicro Server with motherboard X7DB8, chipset Intel 5000P, Xeon 5050 Digium TE110P Software --------------------------------------------- Asterisk version 1.2.12.1

Good day all We got a Wildcard TE110P I installed linux,zaptel,libpti and asterisk I coped over my zaptel.conf and zapata.conf from a previous E100P config But when I try to start asterisk it gives error not bying able to load zap channles: == Parsing '/etc/asterisk/zapata.conf': Found Jan 10 08:17:18 WARNING[-1084595552]: chan_zap.c:9308 setup_zap: Ignoring switchtype Jan 10 08:17:18

Hello, I'm having problem with a wildcard TE110P. As soon as I load the module (wcte11xp for kernel 2.6.10), it spawns a yellow error with or without an E1 plugged-in. Any one managed to set it up in France? Here are my files: zaptel.conf: span=1,0,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 zapata.conf: [channels] language=fr context=default switchtype=euroisdn pridialplan=unknown

I figured it out. The old system (Televantage 3 and 4 I think) has limited specifications on the T1. After setting up the system, I was able to send and recieve calls. I still have some work to do like figuring out faxing and a floating receptionist, but this is a nice start. ----------------------------------------------------Televantage T1 Requirements: Framing: D4 Superframe or Extended