similar to: Polycom oddities: Mixed up digits -> *8 Call Pickup

I'm replacing a SoundPoint IP 600 with a SoundPoint IP 650. I attempted to simply reuse the existing config files for the old phone on the new phone, but the new phone would lock up on the 4th digit when attempted to dial out certain numbers. So, I downloaded the newest firmware and config templates from Polycom, and attempted to migrate the settings. Seems I'm missing something from

I'm working on replacing a SoundPoint 600 with a 650. I need to merge these two sets of digitmaps in the polycom sip.cfg file, because the 650 locks up when I try to use the digitmap from the 600. I've included the default digitmap from a 3.1.3 RevB polycom release. I'd like to merge these two digitmaps, but I don't want to reintroduce the lockup issue I was having with the

I recently had a bear of a time getting a Polycom Soundpoint 500IP up and registered.. Now that its registered I ran into a problem w/ the dialplan. Needing to dial x101 I'd dial 10 - then get a fast buzy.. Also making a local call - dialing 95551212- would give me a fast busy after the 7th digit - so 9555121.. Same w/ LD calls... This dialplan really got me down as I didn't find

I'm using Polycom Soundpoint phones and I want to use some extensions beginning with # for features setup. I'm getting the fast busy "can't match it" signal. I want to match #50 for call forwarding, for instance, and #505551212 to set the call forwarding number and turn it on. I have tftp set up and sip.cfg contains the following: <dialplan

Hi all. I just installed bunch of IP450's and everything went well and my customer is happy.... except that they are unable to transfer calls to other extenstions. They can dial them directly just fine. However, when the user is in a call and presses the transfer soft key, they get dial tone, and start typing the extension, say 1008. But by the time they get 100 typed in, the phone tries

> >> Jason Brown wrote: > >> | Anyone have experiece with polycom phones? > >> | > >> | I am experiencing a really weird problem. In an office > where I have > >> | the following extensions: > >> | On the Polycom phones, when I want to dial from extension > >> 100 to any > >> | extension 120 or above, or dial out, it

Calling all Polycom gurus: I am using Polycom IP601 phones with Asterisk 1.4.21.2 In all Polycom phones, I set the following in sip.cfg. <dialplan dialplan.impossibleMatchHandling="2"> </dialplan> (I leave the digitmap unchanged because I thought setting impossibleMatchHandling will ignore the bitmap) ...so that I could dial any number by entering a variable-size

Does anyone have the polycom soundpoint ip's successfully remotely provisioning? I've got the phone pulling default configs, and it's downloading phone specific information, but it's not actually using that information. Any help would be appreciated :) -- Aaron Daniel Computer Systems Technician Sam Houston State University amdtech@shsu.edu (936) 294-4198

Any Polycom gurus out there? If so, I have a few config file questions. First off, does anyone have the daylight savings time rules written for this Sunday's big change? Secondly, if there any way in the config file to tell the phone not to display the number of missed calls? I don't mind it keeping the missed calls list, I just don't want that running count. Lastly, I am trying

<digitmap =20 dialplan.digitmap=3D"[2-9]11|0T|011xxx.T|[0-1][2-9]xxxxxxxxx|[2-9]xxxxxxx= x x|[2-9]xxxT" dialplan.digitmap.timeOut=3D"3|3|3|3|3|3"/> Don't think it's been modified from the original supplied. ...brig -----Original Message----- From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf

I'm attempting to set up my SoundPoint 501 with my Asterisk server. I've configured DHCP and TFTP and successfully updated both the BootRom and SIP application. I've also created a custom cfg file for this phone's MAC address and the settings seem to be taking just fine. I can see that the phone registers with my Asterisk server but 'sip show peers' reports that the phone

We've just setup our A@H server, with our quad port card. Everything works well so far. One thing I notice is that when I leave the handset on the hook and dial a #, all is well. If I pick up the phone and dial, it cuts off at 10 digits, which is a problem if I need to dial 1+area+phone # (12 digits). The phones are Poly Soundpoint IP 600's. I'm wondering if I've missed a

Hi All, I'm not sure if this is related directly to asterisk or not but on my Polycom 320 when I try to dial a number smaller than 4 digits I get an error on the phone saying "Enter more digits". The dial plan section is listed below. <dialplan dialplan.impossibleMatchHandling="0" dialplan.removeEndOfDial="1"> <digitmap

I am having a strange problem with polycom 501 and dailing. I've read the archives and no one there specifically mentions this problem, so I thought I'd ask here. The problem is that when the user picks up the receiver or pressed new call, sometimes they will enter a number (for example 95072091234) and in the middle of the number the cursor might jump back one digit. So the call above,

Hi BK - >> The blind transfer does not work. >> >> The way we try to blind transfer a call: >> 1. answer the call >> 2. press transfer >> 3. press blind softkey -> the display shows "Blind transfer to:" and >> cursor is in the second line >> 4. enter the number -> when we enter the second digit of the number >> the

hi there I'm setting up asterisk@home and I'm using Polycom IP 500 phones. When I call a number that has a digital receptionist (i.e. "dial 1 or such and such, dial 2 for this and that...") the Polycom doesn't seem to send the extra digits. When I try it with X-Lite things appear to work fine, so I think the problem is with the Polycom configuration. Here's some

Hi, I'm trying to configure a Polycom IP Phone SoundPoint 500 to connect it to my Asterisk PBX but with no success. First of all, I downloaded the SoundPoint IP SIP Administration guide I found on internet and then I tried to make a boot server creating an FTP account on my Mandrake 9.1 Linux box but I needed the following files: 000000000000.cfg sip.cfg phone1.cfg ipmid.cfg sip.ld so I

If you activate (via sip.cfg) the feature Group Call Pickup, its no surprise that asterisk doesn't know what to do with this feature request. But it is being sent as a SIP SUBSCRIBE request, and I'm wondering if, as asterisk stands, there is a way to take advantage of this feature to emulate the "*8#" normal behavior. If anyone has any input, there is also a call parking

This is a dialpaln issue. I solved the same problem recently. For 4 digit extensions you need to append the dialplan statement in the sip.cfg configuration file as follows <digitmap dialplan.digitmap="[2-9]11|0T|011xxx.T|[0-1][2-9]xxxxxxxxx|[2-9]xxxxxxxxx|[2 -9]xxxT|1xxxT" dialplan.digitmap.timeOut="3"/> Michael > I am not sure what I did but blind transfers do not

If you activate (via sip.cfg) the feature Group Call Pickup, its no surprise that asterisk doesn't know what to do with this feature request. But it is being sent as a SIP SUBSCRIBE request, and I'm wondering if, as asterisk stands, there is a way to take advantage of this feature to emulate the "*8#" normal behavior. If anyone has any input, there is also a call parking