similar to: BRI Hunting, using both channels on one msn

I'm looking to use Asterisk with Verizon ISDN centex service in the US. I'd be connecting to an NT1 so I'd need an S/T interface. Users would have SIP phones registered with Asterisk and sharing the ISDN lines. The only PCI ISDN card that will support ISDN signalling in the US seems to be the Eicon Diva Server cards. These are hard to find and very expensive ($2500 for the Quad

Hello Everyone, I am once again wondering about EICON. I have had no success with the Diva Pro or Diva Pro PCI, so my question is, does anyone use an Eicon Server BRI card on Asterisk? Or would I be better off trying to get a split PRI? Regards, Greg

Hello All, I recently put in a zaptel 1fxo/1fxs card. I am experiencing heavy static. Even with the pots line disconnected, if I do a dial I still get static. This way I know it's not the line, but rather something on the card. I tried alternate pci slots. This card has a power connector, does anyone know what the power requirements are? The unit is in a small case with a 2.4ghz p-4 and

Hi! I have some (short) question about the Eicon DIVA (V-)4BRI cards I want to have (short) answered before buying the DIVA card. I know there are several Eicon guys active on the list, thus I ask on the list instead of directly to Eicon so that all other will benefit as well. 1. Do Eicon DIVA (V-)4BRI cards support TE and NT mode? 2. Can the clock (master/slave) be configured independent

Which models of Diva could work with CAPI and asterisk? Thanks Giordano ________________________________ Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di gw@adcomcorp.com Inviato: sabato 1 ottobre 2005 23.46 A: asterisk-users@lists.digium.com Oggetto: RE: [Asterisk-Users] Diva Nope. At least I tried and never could get it

Hi Everybody, Has anybody tried the above (or indeed any other 4XBRI cards) successfully with Asterisk. As far as I can see the above mentioned card is an active ISDN card but supported by it's own I4L driver. This leads to interesting questions particularly regarding echo cancellations (which usually doesn't work on the cheap passive cards with one exception as far as I can see).

Hello All, I am having an odd problem with Armin's chan-capi_cm on builds higher than 7955. It would seem that this happens on anything higher than 7955. What is happening is the isdn is ringing, then asterisk does a goto-if and just hangs. Asterisk itself is ok, but the isdn then rings out or busys out on the other side. Outgoing works fine, this only seems to effect incoming. I

I'm having issues with echo. My setup is Polycom IP501 phones connected to an Adit 600 via T100P. 13 Lines going to the Adit. All echo so far is on the local side (Employees hears own voice, but only on some calls). Watching the channel with ztmonitor, I notice that TXGAIN is pegged out most of the time. RXGAIN is anywhere between 45 and 60%. Is it safe to assume that playing around

Hi everyone, I have Asterisk SVN-trunk-r7498 running for a few months and I'm quite happy with it. However, I am experiencing a quality issue with my AVM Fritz!card PCI which is used with chan_capi. When somebody calls me on this line he hears a lot of noise and I hear "scratches" and "plops". It is very annoying. Below is is my /etc/asterisk/capi.conf I've tried to

Hello Armin, > The card is telling: > > CAPI INFO 0x34a2: No circuit / channel available > > so the other channel must be in use by something else. > Maybe another device on the ISDN line? > I have tested it several times now and always entered "capi info" before and after the call. The answer was always: Contr1: 2 B channels total, 2 B channels free. I'm

Repost, first one never made it to the list... -----Original Message----- From: Gregory Wiktor - ADCom Corp. Sent: Thursday, September 29, 2005 3:20 AM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: Voice Prompts, what do you think? Good voice. Should we record a new prompt-set? Hello all, I have someone working for me who has a nice phone voice. I looked at

On 09/03/2016 10:56 AM, Etienne Dechamps wrote: > C will still need keys in order to establish metaconnections with A and B (as > well as a few other things). However there is no need for C to own any > "Subnets" at all. If somebody breaks into C, he could get access to the vpn network, right? Because the keys are there, it will be possible to use them to get access. Even if

I am trying to understand the difference between the divas4linux available from the Eicom/Dialogic website and the melware version. Am I right in thinking that the melware version is for Trixbox or Asterisk but the Dialogic version is for Asterisk only (i.e. will not work with Trixbox?). I've noticed that some of the things mentioned on the Dialogic web site as included with Divas e.g.

On 09/02/2016 08:51 PM, Etienne Dechamps wrote: > What version of tinc are you using? tinc 1.1 already does what you want out of > the box: packets sent from node A to node B through node C will use a key that > A and B will negotiate between themselves. C doesn't have the key, and will > act as a blind relay. C will not be able to decipher the packets flowing > between A and B.

Hi (Armin?) ! Today I had a problem with Diva Server 4BRI-8M 2.0. Asterisk 1.2.12.1 chan_capi-cm-0.6.5 divas4linux-melware-3.0.f-106.622-1 Asterisk could not receive and make calls on the BRI ports, although the ports looked fine within Asterisk. I usually use "/usr/lib/divas/divactrl dchannel -c 1" to test line activity. This time there was no activity (cryptic log

Hi to all I've mada up my mind and i tried to change from i4l to chan_capi, following some councelling from the gurus. I compiled it up, and when i try to load it in modules.conf, i get that wonderful message and Asterisk does not start: [chan_capi.so]Feb 17 09:21:40 WARNING[16384]: loader.c:239 ast_load_resource: /usr/lib/asterisk/modules/chan_capi.so: undefined symbol: ast_get_group Feb

Hi everybody. I'm trying to setting up a V4 BRI EICON card on ASTERISK 1.0.7 My linux is a debian. It was working during a few days an suddenly (after a lot of reboot) I've got this error message that seems to be very popular but I couldn't find any answer on the net : ==============================================. Asterisk Dynamic Loader Starting: == Parsing

Are there any step by step instrunctions on how to install drivers and I guess bristuff for this card? Just need to use it to handle voice on 2 BRI circuits (UK) then utilise with Asterisk and some Digium cards handling POTS phones (and some VoIP out the back). It's the EICON card stuff and how to make it all work I'm finding confusing? Steve -- NetTek Ltd UK mob +44-(0)7775 755503

Hi; I've got an AAH installation where a customer wants to install an active Eicon DIVA BRI card. AAH is built on Centos 3.5 which is currently at kernel 2.4.21.37. Support for Eicon active cards is built-in. I've debugged and run the A@H install-Eicondiva script but when I try to run divactrl load -c 1 -f ETSI -Debug I get a response : A: can't get card type for DIVA adapter

Hello everyone, I'm having some errors while compiling the source code for an Eicon Diva BRI card. I am using Fedora Core 6 with a compiled from source Linux kernel 2.6.19. I have downloaded the Eicon Diva source RPM (divas4linux_EICON-106.12-1.i386.rpm) and installed it already. When I go to /usr/lib/eicon/divas/src/ and run ./Build, everything starts correctly until that part where it has