similar to: TE405P V2 changes?

Displaying 20 results from an estimated 400 matches similar to: "TE405P V2 changes?"

2006 Dec 18
2
Digium TE405P with French E1 => Red Alert
Hi anyone have a idea for debug my digium TE405P card ? My zaptel.conf: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone = fr defaultzone = fr My Zapata.conf: [channels] language=fr context=from-E1 switchtype = euroisdn pridialplan = unknown signalling = pri_cpe usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes
2009 Sep 01
7
Dahdi configuraion / error
Hello I just updated the kernel, dahdi-linux and dahdi-tools Im also using now asterisk 1.4.26.1 And im still with a red light (not RED/YELLOW anymore): [root at catumbela ~]# /etc/rc.d/init.d/dahdi status ### Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" (MASTER) HDB3/ RED 1 PRI CAS RED 2 PRI CAS RED 3 PRI CAS RED 4 PRI
2005 Sep 30
1
TE410P not working
I'm trying to install a TE410P this is what happens with compiled zaptel 1.0.9, 1.2-beta and 1.0.9 from http://updates.xorcom.com/iso/ this is my zaptel.conf (checked with the provider the values): span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone=it defaultzone=it then I modprobe wct4xxp debug=1 t1e1override=15 and the kernel says : Sep 30 16:12:40 localhost kernel: Zapata
2009 Oct 20
2
Kernel panic w/ DAHDI 2.x/Digium TE220B
I've seen this consistently on three systems, with three different cards, and multiple versions of DAHDI. At first I thought the issue only occurred on newer, Nehalem-based, systems, but I reproduced it on a Core 2 Duo box as well. I've tested with dahdi-linux 2.2.0.2, dadhi- linux-complete 2.0.0+2.0.0, 2.1.0.2+2.1.0.2, and 2.2.0.2+2.2.0. The card is a Digium TE220B which uses the
2006 Apr 30
2
PRI Issue: D-Channel woes
Hi, I am about to pull my hair out after trying to get our PRI up and working. We are switching from a Cisco gateway to an Asterisk box which provides the 23 phone lines for our office. So, because the Cisco gateway is working I can assume I have all the settings right (b8zs, esf, dms100, etc) and the PRI is live (because we are switching over). When dialing from PSTN, I get busy signal. When
2010 Jul 06
0
Problem with wct4xxp - cannot make calls
Hi, I'm having problems with a TE420P card, in which I cannot make calls using spans 2 through 4. After a couple of days of working correctly, spans 2, 3 and 4 start failing (can not make calls). The system is configured to work with SS7. After the ACM message goes out, immediately a REL message is returned. I searched for error messages in /var/log/messages and could not find a clue
2007 May 18
2
TE212P octastic initialization failure
Hi, I'm trying to get a TE212 working on a Dell PowerEdge 1850 running Debian etch using the latest release of libpri (1.4.0), zaptel (1.4.2.1) and asterisk (1.4.4). The initilization of the Octasic echo canceller seems to fail when the wct4xxp module is loaded. [...] VPM450: echo cancellation for 64 channels Failed to open chip, code 00103017! VPM450: Failed to initialize [...] By looking
2009 Aug 26
1
TE4XXP: Version Synchronization Error!
Hello to all I'm using asterisk 1.4 and dahdi. I had everything working fine, and I could place calls through my R2 channel. But now the channel is always "RED" and Im getting this error message: TE4XXP: Version Synchronization Error! Here is my chan_dahdi.conf------------------------------ [channels] language=en context=incomingr2 signalling=mfcr2 mfcr2_variant=ar
2008 Apr 14
8
zaptel 1.4.10 regression with TE220B on Proliant DL380 G5 ?
Hi list, After a lot of testing + troubleshooting, I guess I'm observing what I am now calling a regression with zaptel 1.4.10 (is it?) As such I call for peer feedback, before either asking Digium install support or filing a bug. Thanks in advance! System: HP Proliant DL380 G5 with 2x PCI-X + 1x PCIe riser card OS: Centos 5 Kernel: 2.6.18-53.1.14.el5 (also tested under
2004 Sep 17
4
SS7 E1 cards
Hi, I'm looking into support for SS7 and I found an article (http://www.openss7.com/news13022002.html) which says that OpenSS7 supports Linux Support Inc's T400P-SS7 Quad T1 and E400P-SS7 Quad E1 PCI interface cards. It also says that Linux Support Inc is the primary sponsor of Asterisk. However I cannot find these cards on the Asterisk hardware page
2004 Nov 29
3
TE410P lights don't blink read after the module is loaded
Greetings, According to the FAQ "When you load the module and have no circuit/channel bank the LED's should flash red" I get the "knight rider" lights before the module loads, but after the modules are loaded I don't get any lights, other equipment plugged in or not. The card has been on my shelf a while so I wonder if it needs a firmware upgrade ? Can the cards
2005 Sep 07
1
ztcfg Kills My Dial Tone
I'm using two Rhino channel banks (first 12FXO/12FXS, second 24FXS). These connect to a Digium TE210P card. I'm running kernel 2.6.10 and I've tried Asterisk (w/zaptel) 1.0.9, 1.2 beta, and CVS from today. The results are the same for all versions: Right after I reboot, and modprobe wct4xxp, my analog phone connected to port 13 of the first channel bank (first FXS port) gets a dial
2008 Jan 07
1
Multi-SPAN (4xE1) Zap Group (Outbound)
Hi, Can someone point me to a zapata.conf example that will create a single DIAL OUT group including all 4 spans on a TE4XXP? One friend says to change the group number all to "1" on all 4 spans. Another suggestions says it is possible to have these unique groups (1-4) and to combine all 4 into a single group "5". I like the second suggestion best. Can you guide me to the
2004 Apr 02
1
T100P specs
Does anyone have the physical spec sheet for the T100P from Digium? The one on the website doesn't have what I need. Things like 3.3 or 5v operation, uses n IRQ channels, requires 32-bit PCI, must be installed while standing on one foot and reciting the GPL, etc. Also, if anyone is selling a used T100P or TE4xxP I'd like to talk... Thanks, --Ernest
2007 Jun 07
2
Bridged PRI calls - processor involvement?
On a zaptel TE410p, when a call is bridged PRI - PRI how much involvement does the processor have? We're now seeing chunks of missing audio and I can't tell whether this is due to a kernel upgrade or to a zaptel/libpri/asterisk upgrade. I'm not seeing missed interrupts (from a cat of the proc/zaptel files), any other ideas on how I could go about tracking this down? I'm
2010 Sep 09
2
How to avoid interruptions with DIGIUM
Hello Asterisk community, I'm experiencing some problems with a Digium TE4XXP, the thing is that i'm sharing IRQ with some megasas device: 169: 69917985 0 0 0 0 0 0 0 IO-APIC-level megasas, wct4xxp I've been searching here: http://ubuntuforums.org/showthread.php?t=254623 Should i try in the pass this parameter in the
2010 Jul 12
0
DTFM Detection issues
Hi list, I'm having trouble with DTFM tones detection. Usually, some tones are being received duplicated in Asterisk, some not. As you can imagine, that's a very big problem involving IVR menu options, Meetme conferences protected with passwords, and so on. We are currently using DAHDi 2.2.0.2, module wct4xxp, which is managing a Digium TE220B card, with a hardware echo canceller
2010 Jun 17
1
DTMF detection issues
Hi list, I'm having trouble with DTFM tones detection. Usually, some tones are being received duplicated in Asterisk, some not. As you can imagine, that's a very big problem involving IVR menu options, Meetme conferences protected with passwords, and so on. We are currently using DAHDi 2.2.0.2, module wct4xxp, which is managing a Digium TE220B card, with a hardware echo canceller
2014 May 30
1
Flashing Red Lights in TE420 (5th Gen) Card
I have the following software installed in a Centos Box with a TE420 (5th Gen) card. . Centos 6.5 64-bit . Asterisk 1.4.22 . dahdi-linux-complete-2.9.1.1+2.9.1 . libpri-1.4.14. Even without plugging in the ISDN into span 1, all 4 spans are flashing red. Plugging an E1 into span 1 makes no difference. My system.conf is just simply: loadzone=au defaultzone=au span=1,1,0,ccs,hdb3,crc4 bchan=1-15
2004 Dec 21
2
TE405P E1 coax cables with balun
Hi, I am new with asterisk. I am setting a Wildcard TE405P. E1s in Italy come in on a pair of RG-59 coax cables with BNC connectors. So I need an adapter/balun http://www.allcomtlc.com/al_g703n3.htm . I have It but I am not sure that It works. I have configured my asterisk in this way: zaptel.conf span=1,1,0,ccs,hdb3,crc4 dchan=16 bchan=1-15,17-31 loadzone=it defaultzone=it zapata.conf