similar to: Issue with zapata.conf "immediate" setting

Hi list, Ive got a server with 6 ports on it (4+2 port card) we have a DS3 delivering all voice DS1's to us. Carrier has a trunkgroup for the first 8 span (we only have the first 6 plugged in right now). Everything works fine until we fail the primary D channel (D's are on 24,48) the secondary then picks up and outbound calls do not work, if we reboot Asterisk the D on 48 comes up and it

Can anyone describe the asterisk implementation of this any better than the sample config files do? from zapata.conf ; Trunk groups are used for NFAS or GR-303 connections. ; ; Group: Defines a trunk group. ; group => <trunkgroup>,<dchannel>[,<backup1>...] ; ; trunkgroup is the numerical trunk group to create ; dchannel is the zap channel which will

We have integrated an Asterisk (TE110P) and a Mitel SX200. We usually get over 500 frame errors and over a 500 slip errors per hour. When the errors reach 1000 per hour the Mitel will take it's T1 card offline. At that point no calls can be routed from the Asterisk server to the Mitel and the TE110P reports a Yellow alarm. What can be causing all these Frame and Slip errors? We have been

Hi, I'm a lab manager / supervisor at our labs. We've had Asterisk in use for over a year directly hooked to the PSTN - a no brainer for configuration (although I had to fix some AT&T specific things in libpri). Right now I have two big challenges. One is to hook our box up lineside to a Lucent Definity G3R. Avaya is chasing this from their end, but we had the highest level of

I've got a system with 5 pri circuits configured into a CFAS group with a primary and secondary d channel. There are three TE410P cards in the system. The 5 circuit span are located as follows: circuit 1 on span 5 circuit 2 on span 1 circuit 3 on span 6 circuit 4 on span 2 circuit 5 on span 9 primary d chan is on chan 24 of span 5 (chan 120) secondary d chan is on chan 24 of span 1 (chan

Hi All, I have just migrated from Asterisk 1.0.0 to Asterisk 1.0.5 and I have an X100P installed. The old asterisk was working, but now the new version isn't picking up any calls! However, I did notice that after installation, I performed modprobe zaptel and modprobe wcfxo and they worked fine, but when I executed ztcfg, I get the following errors: ioctl(ZT_LOADZONE) failed: Invalid

[18884732963 at from-fax-machine:... - your call is hitting the from-fax-machine context - yet your 'fax' exten is in the from-pstn-4 context. See the "[2011-03-17 13:40:29.6] NOTICE[8825] chan_dahdi.c: Fax detected, but no fax extension" line. When Asterisk detects an incoming fax tone - it tries to automagically route the call to the 'fax' extension in the SAME

I am running Asterisk 1.6.2.17.2 with a Openvox A400 card with 2FXO/2FXS modules. I'm trying to set-up things to route analog fax calls from a FXO port to an analog fax machine on a FXS port on the same card. Outgoing faxes work just fine. But incoming faces are routed to the right DAHDI extension, but the call dropped right as the fax machine rings for the first time. The fax machine

We've been working for the past 2 weeks to get a new V400P working with our PRIs from the telephone company. We're trying to get the Asterisk server setup as a VoIP gateway for SIP and AIX. We can make SIP-SIP calls, but all calls from or to the PRI fail. This is the applicable entries from the Asterisk log (configuration files follow) for a call coming from the PSTN on the PRI. I

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

Hi, I wonder if anyone is using Digium's TE110P card on an E1 connection. I have been try to, but so far it wasn't much of a success. It only works more or less in EuroISDN as PRI CPE. And even that config gives me some trouble with channel negotiation. My current config: *zaptel.conf:* span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=be defaultzone=be *zapata.conf:* [trunkgroups]

Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]:

Hi, I have just set up Asterisk to use an E1 line with a Digium card. And I can call both in and out, but my outgoing line is all ways identifying itself as the same number, and i can't even change it to another number in the same number series. Do anyone have some clue on how to fix this. I'm using Asterisk 1.6.2.13, libpri 1.4.11.4 and DAHDI 2.4.0. /etc/dahdi/system.conf:

Deat all, I am in middle of integrate Asterisk with Toshiba astrata legacy pbx. Following is my setup *Asterisk <-> Digium TE110P <-> E1 card in toshiba pbx <-> Toshiba PBX* A =============================================> B C <============================================ D Asterisk PBX and strata PBX connected using back to back E1 cross cable. Physicall connectivity

Hello All I'm using asterisk 1.1.X and MFCR2 lib version 0.03pre2. when i call to E1 (connected with asterisk), chan_unicall don't detected event incoming call and show error. error messages: *CLI> Warning, flexibel rate not heavily tested! Rx CAS bits 0x9 [ 10000/ 0/ 0] Line unblocked -- R2 Channel 4 unblocked Rx CAS bits 0x9 [ 10000/ 0/ 0] Line unblocked -- R2

Hi there I have a TE110P card fitted in my linux box running : Linux version 2.6.9-5.ELsmp (bhcompile@decompose.build.redhat.com) (gcc version 3.4.3 20041212 (Red Hat 3.4.3-9.EL4)) #1 SMP Wed Jan 5 19:30:39 EST 2005 I followed the installation steps on digium website...no errors reported. The modules seem to have loaded...here's what lsmod shows: Module Size Used by

When I send a call from my TE410P using E&M, the legacy PBX answers the call but doesn't route it. Any idea what this could be? I assume the digits aren't being delivered properly to the legacy pbx. Any suggestions on what config settings to muck with? Asterisk SVN-branch-1.2-r40901 built by root @ pbx04 on a i686 running Linux on 2007-01-14 14:05:02 UTC zaptel.conf

Hi All i'm using sangoma card. connected to E1, my wanpipe file as #================================================ # WANPIPE1 Configuration File #================================================ # # Date: Fri May 27 00:25:04 GMT+7 2005 # # Note: This file was generated automatically # by /usr/sbin/wancfg program. # # If you want to edit this file, it is # recommended

Hello, I'm running Asterisk@home 2.5 asterisk 1.2.4 zapatel 1.2.2 libpri 1.2.2 on a Dell Poweredge 2850 (1 CPU) with a TE210P I have 2 t1 circuits using NFAS with dchan on 24 and no backup dchan. I am able to receive inbound calls on all channels and can only make outbound calls on channels 25-48. Attempting to make an outbound call on channels 1-23 results in congestion.

Hi, I'm having trouble configuring and E1 link , I know the E1 is a PRI and the switchtype is 5ess. The problem is that everytime I try to dial I got and error saying that it was unable to open the zap channel . Devices are created in the /dev/zap directory and I can open them with a cat /dev/zap/1. I can also see the channels in /proc/zaptel/1. Thanks in advance [zaptel.conf]