Displaying 20 results from an estimated 1000 matches similar to: "100% CPU with Unicall and * head"
2007 Jan 17
1
Asterisk + Unicall + Telmex E1 MFC/R2 Argentina + Meridian
Hi everyone!
I'm having some issue trying to place calls with asterisk connected to
an E1 R2 from Telmex Argentina. The other E1 port is connected to a
Meridian which also uses R2 protocol. Calls sometimes fail with
different error messages such as: Unicall protocol error 32773, 32772,
32769. Some other calls fail saying:
Far end disconnected(cause=Destination out
of
2005 Aug 03
2
MFC/R2 Mexico Unicall Blocked
I've been trying to configure an E1 in Mexico using unicall, i went
into vozdigital, googled this list, and finally followed this
instructions:
http://voip-info.org/tiki-index.php?page=Asterisk+MFC+R2
I have 10 PSTN numbers and 10 "lines" assigned, so i only have 10
"channels" assigned from my telco.
However when i try to simulate a call using this call file:
--------call
2006 Apr 21
1
Unicall MFRC2 Problems with BrT.
Hello All,
I'm facing problems with Unicall on this scenario :
CentOS 4.3 - Running on x86_64
Asterisk 1.2.7.1
Zaptel 1.2.5
When running zttool , shows all Spans OK.
But I can't receive and make calls.
I tried to change many parameters and still doesn't work.
Any clues ?
* unicall.conf
[channels]
language=br
context=incoming-pstn
usecallerid=yes
hidecallerid=no
immediate=no
2007 Jul 27
2
Unicall/Dont know how to handle Accepted
Hi,
I've finally got running Asterisk 1.2.14 with UniCall & MFC/R2 patches, I
can generate calls and all seems OK but I cannot receive any call, this is what I get:
MFC/R2 UniCall/3 <- 0001 [1/IDLE /Idle /Idle ]
MFC/R2 UniCall/3 Detected
MFC/R2 UniCall/3 Creating a new call with CRN 32769
MFC/R2 UniCall/3 1101 -> [2/DETECTED/Seize ack/Seize ack ]
2008 Jan 18
1
R2-Unicall Asterisk as CPE and as CO
Hi!
Im having some troubles trying to configure * as a bridge between a telco
and a pbx with R2, the scenario is this:
------------ E1/R2 --------- E1/R2 ------------
| Telco |-------------| * |-------------| PBX |
| (Telmex) | --------- | |
------------ ------------
I can receive calls from the telco
2010 May 12
1
problems with unicall
Hello,
i'm using asterisk 1.4.9 in fedora 7, i was compiled its with this package:
libpri-1.4.2
asterisk-1.4.9
spandsp-0.0.4
unicall-0.0.5pre1
libmfcr2-0.0.3
libsupertone-0.0.2
libunicall-0.0.3
zaptel-1.4.4
i'm using a E1 pci card with R2 but they not work, when I start the asterisk
its generate this log:
[May 12 08:53:24] WARNING[30814] channel.c: No channel type
2005 Jan 18
1
Asterisk - libunicall - MFCr2 *** settings problems ??? ***
Dear Steve and *.* e1r2 developers and users,
now MFCR2 is successfully installed! many thanks for
your help.
I'm living in Argelia. I have configure my MFCR2
according argentina R2 settigs. (look at the end of
the message)
the testcall run perfectly (only warnings and I think
that is just debug).
but I have many problems and when I run
Asterisk-MFCR2, generally in the begging no errors
2007 Mar 19
1
Unicall Brazil
Hi.
I am in the Brazil.
I have a problem on Unicall for Asterisk 1.4.
I am working with E1 with 30 channels.
Message when it receives calls:
chan_unicall.c:2603 handle_uc_event:unicall/1 protocol error.cause 32772.
My files:
/etc/zaptel.conf:
span=1,1,0,cas,hdb3
cas=1-15:1101
cas=17-31:1101
loadzone = br
defaultzone = br
fxoks = 32-55
/etc/asterisk/unicall.conf:
[Channels]
language=br
2006 Jun 09
2
Unicall acting really funny
Hello guys!
I hope you bare with yet another newbie on the list! :-)
I am trying to setup an asterisk installation in between a Siemens
HiPath 3800 and my local carrier (Telefonica/Brazil). Both running R2.
ISDN is not an option on the carrier. :-(
I could apparently setup both E1s just fine according to zttool
(both OK with no alarms) but, and this is where it starts to get
2008 Feb 18
1
mfcr2 stuck
Hello
I'm using mfcr2 support (unicall) in asterisk 1.4. Everything is working fine, asterisk can answer calls.
But after some random period of time mfcr2 module stuck. When I make a call to my * box I can hear only signal of getting caller ID ("tritirirti" - like jumping on :) ) and connection is terminated by my telecom operator. When everything I ok after few seconds of this
2008 Jan 30
1
Unicall CRN 32769 - far disconnected cause=Switching equipment congestion [42]
Dears,
After weeks trying to contact support of my telecom about 'Seize Ack'
because that is not returned, was a lock for make calls on my E1s.
Now I receive back de Ack and get ready to make calls, but the technical
support reports to me that my attempts to call do not send any digits to
the oder site (telecom station). 8 seconds after start 'Unicall event
Dialing' the line
2008 Apr 01
1
Unicall + incomplete DNIS on international calls
Hello everybody, i'm from Mexico, at the time i?m working on a production
server with asterisk 1.2.25 + spandsp-0.0.4 +
libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I
installed this version of astunicall that i downloaded from
http://www.moythreads.com/astunicall/
Everything works fine, i'm able to make outgoing calls and recive incoming
calls with all ANI and
2005 Jun 21
1
chan_unicall, bug in 1.0.X - 99% CPU
I have a problem with inbound and outbound calls in asterisk. I read previous
thread, and then test new versions of unicall, but I don't have success, the
problem persist. The system suffers CPU peeks with a single conversation,
with an interval of 5 or 10 seconds.
My system has:
asterisk 1.0.5
zaptel 1.0.4
libunicall 0.0.3-pre3
hardware: E100P
Also, I made traces with strace, but all
2006 Feb 07
1
MFC/R2 in Brazil
I don?t know if the last message was with content. So, I sent again. I have
installed a Digium card TE210P and unicall for use MFC/R2. I think that it?s
all right but I can?t make and receive calls. I?m using asterisk 2.1 with
the patch made by Jos? P. Leit?o and the follow libs:
libsupertone-0.0.2
libunicall-0.0.3
libmfcr2-0.0.3
zaptel 2.1
My number is 34318300. The Telco send me only 8300.
2008 Jan 12
2
My latest MFC/R2 update with asterisk-1.4.17
Hi all,
I still haven't seen my first post (cry for help) so I'm not sure if these
are going through or not ...
I've played with the box all day today ... I got it to quit seg faulting
finally by playing with the config files.
Currently I have 4 spans configured for a Digium TE420B (With Octastic DSP)
Here is my zaptel.conf: (I know the device connected to spans 1-3 are
providing
2005 Aug 27
1
Nortell Release 11 and Asterisk E1
Hi, i have one Asterisk with a Digium E1 card, and a Meridian Nortel
Release 11.
I need to connect both of them. We are using MFC/R2 for this..
The Diagram:
[ NORTEL ] ( AMI ) ------------------------------------------------
(DIGIUM) [ ASTERISK]
we have green light at the digium card, and at asterisk we see all 31
channels as idle.
But when i want to recive a call from the Nortel to the
2005 Aug 27
5
Asterisk and a Meridian Nortell Release 11
Hi, i have one Asterisk with a Digium E1 card, and a Meridian Nortel
Release 11.
I need to connect both of them. We are using MFC/R2 for this..
The Diagram:
[ NORTEL ] ( AMI ) ------------------------------------------------
(DIGIUM) [ ASTERISK]
we have green light at the digium card, and at asterisk we see all 31
channels as idle.
But when i want to recive a call from the Nortel to the
2005 Jul 28
0
Unicall Dialing problems
Hi everybody
We are having periodically troubles with the outbounds calls, seem
like the PBX cannot end to dial the entire string of numbers This is
output from the PBX., few minutes after all work fine again ... :(,
and few minutes after the same problem appears.
Thanks in advanced ...
Regards
This is the PBX aout and my zaptel, zapata confs.
Runing
asterisk 1.0.9
libmfcr2-0.0.2
2006 Mar 25
2
help on mfc/r2
Hello there!
I've problem with setting up unicall / mfcR2.
can't find proper notation for channel, trying unicall/1,
unicall/1/1001, unicall/g1, unicall/g1/1000
and still having no luck.
klaudia*CLI> !cp call /var/spool/asterisk/outgoing
-- Attempting call on Unicall/1001 for application Dial(363) (Retry 1)
Mar 25 09:29:34 NOTICE[19920]: channel.c:2429 __ast_request_and_dial:
2005 May 20
1
MFC&R2 Venezuela with libunicall
Hi,
I am trying to configure * 1.0.7 box with a Digium Wildcard TE110P T1/E1 and libunicall latest code.
All libs compiled successfully and the E1 have a green light!
I am able to receive a call (or at least) testcall shows some information when an incoming call is received so the drivers and basic configuration is working.
My * box has 2 cards, one TDM400B (2 fxs and 2 fxo) and one TE110P