kaws elchamal
2005-Jan-18 12:39 UTC
[Asterisk-Users] Asterisk - libunicall - MFCr2 *** settings problems ??? ***
Dear Steve and *.* e1r2 developers and users, now MFCR2 is successfully installed! many thanks for your help. I'm living in Argelia. I have configure my MFCR2 according argentina R2 settigs. (look at the end of the message) the testcall run perfectly (only warnings and I think that is just debug). but I have many problems and when I run Asterisk-MFCR2, generally in the begging no errors occures. after random time many inopportune errors occures: sound-cuts, dumb intervals, drop calls and disconnections!!! I think that R2 settings I use are not adapted to Argelian R2 settings. I will try change them but I have not idea where I must do changes. Please help me. Regards, kaws P.S: in the following: my configuration - Argelian R2 parameters and an example of error. *********************** my configuration is : unical.conf: protocolclass=mfcr2 protocolvariant=ar,20,4 protocolend=cpe span=1,1,0,cas,hdb3 cas=1-15:1101 cas=17-31:1101 loadzone=us defaultzone=us zaptel.conf: span=1,1,0,cas,hdb3 cas=1-15:1101 cas=17-31:1101 ***************************************************** the R2 setting of argelia according to quintum are : CD-Bits ::::::::::::::::::::::: 0001 Invert-Bits ::::::::::::::::::: 0000 DNIS Length ::::::::::::::::::: 9 digits * Answer Tone ::::::::::::::::::: A-6 Send 1st Digit :::::::::::::::: 1 Group B Xmt Idle Tone ::::::::: B-6 Group B Xmt Busy Tone ::::::::: B-3 Group B Rcv Idle Tones :::::::: B-2 & B-3 Group B Rcv Busy Tones :::::::: B-1 & B-2 ANI Request ::::::::::::::::::: Do not request ANI ANI Length ANI Category Request Tone ANI Tone Request ANI Category :::::::::::::::::: I-1 ANI Calling Party Category :::: II-1 Seizure Ack Timeout ::::::::::: 150ms Release Guard Timeout ::::::::: 600ms * Always double-check the DNIS length with your carrier *************************************************** example of inopportune disconnection: Jan 17 10:04:17 WARNING[-1120736336]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Rx bits 0x9 [1/ 20/103/107] Jan 17 10:04:17 WARNING[-1120736336]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Far end disconnected - state 0x20 Jan 17 10:04:17 WARNING[-1120736336]: chan_unicall.c:2548 handle_uc_event: UC event Far end disconnected Jan 17 10:04:17 WARNING[-1120736336]: chan_unicall.c:2854 handle_uc_event: Far disconnect cause 16 Jan 17 10:04:17 WARNING[-1120736336]: chan_unicall.c:1088 unicall_hangup: unicall_hangup(UniCall/5-1) Jan 17 10:04:17 WARNING[-1120736336]: chan_unicall.c:1263 unicall_hangup: Causes 0 16 Jan 17 10:04:17 WARNING[-1120736336]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 mfcr2_DropCall() Jan 17 10:04:17 WARNING[-1120736336]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Call disconnected - state 0x800 Jan 17 10:04:17 WARNING[-1114432592]: chan_unicall.c:2548 handle_uc_event: UC event Drop call Jan 17 10:04:17 WARNING[-1114432592]: chan_unicall.c:2892 handle_uc_event: Doing a uc_ReleaseCall Jan 17 10:04:17 WARNING[-1114432592]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 mfcr2_ReleaseCall() Jan 17 10:04:17 WARNING[-1114432592]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Tx bits 0x9 [1/ 1000/106/107] Jan 17 10:04:17 WARNING[-1114432592]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Destroying call with CRN 32769 Jan 17 10:04:17 WARNING[-1114432592]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 release_guard_expired Jan 17 10:04:17 WARNING[-1114432592]: chan_unicall.c:2548 handle_uc_event: UC event Release call __________________________________ Do you Yahoo!? All your favorites on one personal page – Try My Yahoo! http://my.yahoo.com
kaws elchamal
2005-Jan-20 03:37 UTC
[Asterisk-Users] Asterisk - libunicall - MFCr2 *** settings problems ***
Dear Steve and *.* e1r2 developers and users, now MFCR2 is successfully installed! many thanks for your help. I'm living in Argelia. I have configure my MFCR2 according argentina R2 settigs. (look at the end of the message) the testcall run perfectly (only warnings and I think that is just debug). but I have many problems and when I run Asterisk-MFCR2, generally in the begging no errors occures. after random time many inopportune errors occures: sound-cuts, dumb intervals, drop calls and disconnections!!! I think that R2 settings I use are not adapted to Argelian R2 settings. I will try change them but I have not idea where I must do changes. Please help me. Regards, kaws P.S: in the following: my configuration - Argelian R2 parameters and an example of error. *********************** my configuration is : unical.conf: protocolclass=mfcr2 protocolvariant=ar,20,4 protocolend=cpe span=1,1,0,cas,hdb3 cas=1-15:1101 cas=17-31:1101 loadzone=us defaultzone=us zaptel.conf: span=1,1,0,cas,hdb3 cas=1-15:1101 cas=17-31:1101 ***************************************************** the R2 setting of argelia according to quintum are : CD-Bits ::::::::::::::::::::::: 0001 Invert-Bits ::::::::::::::::::: 0000 DNIS Length ::::::::::::::::::: 9 digits * Answer Tone ::::::::::::::::::: A-6 Send 1st Digit :::::::::::::::: 1 Group B Xmt Idle Tone ::::::::: B-6 Group B Xmt Busy Tone ::::::::: B-3 Group B Rcv Idle Tones :::::::: B-2 & B-3 Group B Rcv Busy Tones :::::::: B-1 & B-2 ANI Request ::::::::::::::::::: Do not request ANI ANI Length ANI Category Request Tone ANI Tone Request ANI Category :::::::::::::::::: I-1 ANI Calling Party Category :::: II-1 Seizure Ack Timeout ::::::::::: 150ms Release Guard Timeout ::::::::: 600ms * Always double-check the DNIS length with your carrier *************************************************** example of inopportune disconnection: Jan 17 10:04:17 WARNING[-1120736336]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Rx bits 0x9 [1/ 20/103/107] Jan 17 10:04:17 WARNING[-1120736336]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Far end disconnected - state 0x20 Jan 17 10:04:17 WARNING[-1120736336]: chan_unicall.c:2548 handle_uc_event: UC event Far end disconnected Jan 17 10:04:17 WARNING[-1120736336]: chan_unicall.c:2854 handle_uc_event: Far disconnect cause 16 Jan 17 10:04:17 WARNING[-1120736336]: chan_unicall.c:1088 unicall_hangup: unicall_hangup(UniCall/5-1) Jan 17 10:04:17 WARNING[-1120736336]: chan_unicall.c:1263 unicall_hangup: Causes 0 16 Jan 17 10:04:17 WARNING[-1120736336]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 mfcr2_DropCall() Jan 17 10:04:17 WARNING[-1120736336]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Call disconnected - state 0x800 Jan 17 10:04:17 WARNING[-1114432592]: chan_unicall.c:2548 handle_uc_event: UC event Drop call Jan 17 10:04:17 WARNING[-1114432592]: chan_unicall.c:2892 handle_uc_event: Doing a uc_ReleaseCall Jan 17 10:04:17 WARNING[-1114432592]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 mfcr2_ReleaseCall() Jan 17 10:04:17 WARNING[-1114432592]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Tx bits 0x9 [1/ 1000/106/107] Jan 17 10:04:17 WARNING[-1114432592]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Destroying call with CRN 32769 Jan 17 10:04:17 WARNING[-1114432592]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 release_guard_expired Jan 17 10:04:17 WARNING[-1114432592]: chan_unicall.c:2548 handle_uc_event: UC event Release call __________________________________ Do you Yahoo!? Yahoo! Mail - Helps protect you from nasty viruses. http://promotions.yahoo.com/new_mail