similar to: Junghanns quadBRI on Dell PowerEdge

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable

Hi All I have a Junghanns BRI 4 port installed where only the first channel of each line is working i.e. channels 1 and 4 work but 2 and 5 don't. Our config is the same on this box as 15 other similar installations where all works well. the only error I see is in /var/log/messages: Jun 28 15:49:31 pbxct kernel: qozap: CRC error for HDLC frame on card 1 (cardID 0) S/T port 2 Jun 28 15:51:27

Hi everyone. We have a problem here... Hope somebody can give us some hints. We have a HP ProLiant DL180 G6 Server with a Debian/Lenny sytem. Asterisk 1.4.21.2 (1.4.21.2~dfsg-3+lenny1) with zaptel (1.4.11) and libpri (1.4.3) is installed. There is a QuadBRI-Card installed: # lspci -vv -s 06:04.0 06:04.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)

Hi all, I'm trying to get a junghanns QuadBRI to coexist in the same machine as a Digium TDM400P card (so I can run the ISDN lines in and bridge with analog phones plugged into the TDM). I'm having a problem loading the modules. If I follow the BRIstuff (0.3.0-pre-1l) install method.... it's to modprobe zaptel, then insmod qozap.o I'm on Debian 2.4.31. That works. But then I

Good day all Is there a fix for these errors yet for the junghanns cards Jul 26 17:15:05 pbx1 kernel: qozap: dropped audio card 1 cardid 0 bytes 6 z1 1 z2 107 Jul 26 17:15:18 pbx1 kernel: qozap: dropped audio card 1 cardid 0 bytes 6 z1 10 z2 116 Jul 26 17:15:18 pbx1 kernel: qozap: dropped audio card 1 cardid 0 bytes 5 z1 118 z2 97 Jul 26 17:16:33 pbx1 kernel: qozap: dropped audio card 1 cardid

Hi everybody I hope that somebody can help me with the following .... I have 2 quadbri cards 2 - 1t0 cards 1 pabx alcatel 4200 I would like to connect my asterisk to the alcatel , I installed bristuff 0.3.0-1p , loaded the zaphfc driver in NT mode configured zaptel and zapata , it works great. then I removed the 1 t0 card, added the quadbri loaded qozap : insmod qozap.ko ports=15 ( 4 ports

Hi there, I am attempting to set up a simple BRI and SIP based platform using * with the quadbri card (it's not sharing an IRQ). I enclose my zaptel and zapata.conf files. For the inital test I'm simply trying to connect to the * demo menu. The drivers compile (with a few warning that I believe aren't important - see attachments). chan_zap comiles with the warning: chan_zap.c:

- I'm not a Linux user i'm trying to get in it ... - Fedora core 1 - QuadBRI card bought from junghanns.net - We want to use the card in TE mode to connect to the TELCO - Downloaded BRISTUFF0.0.2(stable) latest from junghanss.net/asterisk - followed the instructions on voip-info.org - compiled everything still got the error when "make load" in qozap : insmod ./qozap.o

Hi- Anyone using the Junghann's quad BRI card and the Digium E100P in the same system? I'm having a configuration problem where I can configure the cards one at a time (with the appropriate drivers loaded) in a system, but when I try them both together, neither will work. They both work fine one at a time. Probably has something to do with the channel numbering. I've tried

Hi, I have installed a quadBri card, with Asterisk-1.0.10 and the bristuff-0.2.0-RC8s (* 1.0.10) When calling 0207654321 the following happens: -- Executing Goto("Zap/1-1 ", " salsa-helpdesk-day|s|1 ") in new stack -- Goto (salsa-helpdesk-day,s,1) -- Executing Dial ("Zap/1-1 ", "Zap/g1/0201234567|30 ") in new stack -- Requested transfer capability:

hello, Here (http://updates.xorcom.com/astribank/bristuff/1.4/INSTALL.html) you can read : cd qozap modprobe zaptel insmod qozap.o (for kernel 2.4) insmod qozap.ko (for kernel 2.6) ztcfg I thought modprobe was a replacement for insmod. Can someone be kind enough to explain : 1. the difference between modprobe and insmod, 2. why should both commands be issued, 3. how modprobe and insmod compare

Hi, I'm trying to install a Junghanns quadbri for a few days but i stay with an asterisk error. (Everyone is busy/congested ) Asterisk is working with a Fritz PCbut from one year and now i want to add the quadbri. The quadbri card has been configured in NT mode and with no 100 ohms S/T termoination. (I'm not sure if the S/T parameter is correct) I have installed the bristuff package

Hi, I have an asterisk box with a QuadBRI. I am close to make it work like I want: Incoming calls to SIP are OK, outgoing calls are quiet working thanks to Michael Sandee advices. My real problem is that my * box is freezing very often when I probe qozap (bri-stuff 0.0.2). I have tried two distribs (Debian Kernel 2.6, Mandrake 9.1 Kernel 2.4) and it always work for a few minutes and freezes. At

Hi all, Using Asterisk 1.0.10-BRIstuffed-0.2.0-RC8q with a Junghanns quadBRI (2 spans connected) and a Digium TDM400 for extensions Shouuld I be worried about these lines that keep showing up in my /var/log/messages? qozap: dropped audio card 1 cardid 0 bytes 6 z1 10 z2 116 qozap: dropped audio card 1 cardid 0 bytes 6 z1 50 z2 28 qozap: dropped audio card 1 cardid 0 bytes 6 z1 59 z2 37 .. ....

Hi all, We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap modprobe wcfsx then the ztcfg output this: Zaptel

I installed the QuadBri card in my * server. I'm installing * on a RedHat 9 server I run the install.sh file. So far no problems. If I try to start /sbin/ztcfg -v -c /etc/zaptel.conf I will see the following error: Zaptel Configuration ====================== SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 2: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 3: CCS/ AMI Build-out:

Hi all, this time with the complete configuration files... We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap

Hello, I have an Asterisk system with kernel 2.6.18.1 and one quadbri. I have installed the latest bristuff patches (0.3.0-PRE-1s). The system works fine, but when I do a "reboot", the system hangs unloading module "qozap". Is there any known problem with latest 2.6 kernels and qozap module? Thanks. -- Paco Brufal <pbrufal@servitux.es> ServiTux Servicios

I am unable to make quadbri board to work in NT mode, in TE mode it works OK. I have set 5 jumpers to NT mode. Dmesg shows everything OK: qozap: Junghanns.NET quadBRI card configured at mem 0xd084e000 IRQ 9 HZ 100 CardID 1 qozap: S/T ports: 4 [ TE TE TE NT ] qozap: 1 multiBRI card(s) in this box, 4 BRI ports total. from Asterisk side seems to be ok. pri show span 4 Primary D-channel: 12 Status:

Hello, I am trying to install the drivers for the Junghanns quadBRI card, but am having a problem. I have essentially followed the procedure from http://www.voip-manager.net/installation-linux-asterisk.php. At the stage to install the ISDN card I have completed the following: 1) downloaded the bristuff-0.2.0-RC8q.tar.gz to /usr/src 2) unpacked it in /usr/src - tar xvzf bristuff-0.2.0-RC8q.tar.gz