similar to: 2 TDM04B In Asterisk at home

Interesting story. I was following up any wild goose chase i could to find a resolution including cleaning dust out of the machine. At 4 pm I plugged the line in and called for the sake of luck, and it was back to working. In the mean time, thanks for the troubleshooting advice. I will keep this in my log book so I have the steps for next time something goes awry. ------------------------------

Hi, Some weird problem (or I'm too sleepy) happens with a tdm04B revision G (4fxo) Steps: modprobe zaptel modprobe wctdm ztcfg -vv /etc/zaptel.conf fxsls=1-4 # TDM04B defaultzone=us loadzone=us /etc/asterisk/zapata.conf signalling=fxs_ls group=1 context=incoming channel => 1-4 modprobe zaptel and wctdm load fine, however ztcfg -vv shows: 0 channels configured Im using centos 4.4 with

I already have one Digium TDM04B installed in my server working fine. I just received 2 more so I did added them to my server. When I booted again linux told me that it found new hardware I said ignore. Then I log in as usual. I did ztcfg -vv to see if it sees 12 channels now instead of 4 but it only see 4. So then I did again modprobe zaptel, then modprobe wcfxo and wcfxs hoping it would see

We are using AAH with Asterisk 1.2.7.1 with a TE405P as listed below. We are getting frequent restarts on the spans which lead to dropped calls. I have pasted some hopefully pertinent information below -- anyone have any clues that might help? Thanks Next line is repeated throughout messages, going through every channel in every connected span. asterisk/full.1:Apr 24 01:15:25 VERBOSE[4196]

Hi: I had an fxo card from Digitnetworks and it was working fine on my Asterisk box. I then replaced it with TDM04B. I changed the zaptel and zapata to include the four channels. When I run ztcfg, I get configuration errors: Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04:

We have occasional echo, mostly on lines that come across as quiet.. I am trying to troubleshoot how to disolve the echo. i have tried the steps on voip wiki, but have not recently been able to make any difference. the echo isnt horrible most of the time, and seems extremely random in that i can call a number once without echo, then dial the same number a second time and get echo. things i am

I am looking at phones for my asterisk system and seem to have a problem. The only Power over Ethernet phones I can find that support the IEEE standard are 3com. Cisco uses its own proprietary ( and is expensive to boot ), snom has a different but equally non-IEEE method, and i'm havent found another phone that I'm confident can do the job for our office. Whats a good high quality ip

Hi, I would like to construct a transition matrix from a data frame with annual transitions of marked plants. plant<-c(1:6) class<-c("seed","seed", "seed", "veg", "rep", "rep") fate<-c("dead", "veg","veg","rep", "rep", "veg") trans<-data.frame(plant, class, fate)

I would like to install a TDM04B with Asterisk@Home 2.4 and Asterisk@Home 1.5 but I didn't find documentation about this installation. Thanks in advance, Nelson -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060206/85ff5252/attachment.htm

Hi, My name is Jos?? Mar??a G??mez, and I am pretty new in R. Thus, I apologize deeply if my questions are extremmely na??ve.I have checked several available books and URL's, without finding any answer. I'm trying to fit Generalized Linear Mixed Models via PQL. Below I provide the structure of my data set. Year and Plot are random variables. Fate is the binomial dependent. I have severe

Hello I have installed a TDM04B and disabled any devices not required in my PC. (TDM04B is analog card with 4 ports to plug into telephone co lines). I am running this version of * Asterisk CVS-HEAD-01/10/05-02:11:15-AstLinux built by root@ls on a i686 running Linux As you see below the wctdm module is loaded: pbx root # lsmod Module Size Used by binfmt_misc 12296 1 - Live

I have data on the proportion of clutches experiencing different fates (e.g., 4 different sources of mortality) for 5 months . I need to test 1) if the overall proportion of these different fates is different over the entire study and 2) to see if there are monthly differences within (and among) fate types. Thus, I am pretty sure this is an RM analysis -( I measure the same quadrats each month).

On 12/08/14 12:13 PM, Erik de Castro Lopo wrote: > Martijn van Beurden wrote: > >> >Sorry, most of the testmaterial isn't copylefted, and I don't >> >think it is possible to get a nice copylefted test library. > I don't think we need it to be copy left. We would keep it as > a separate git repo of test files, and we could probably just > use snippets

I had a working Asterisk 1.4.24.1 installation on SUSE 9 Linux but SIP only. I then downloaded and installed latest Zaptel and could not get Zaptel working. So I downloaded Asterisk again and re-installed. But still problems: Here is my ztcfg output: asterisk:/etc/asterisk # ztcfg -vvvvv Notice: Configuration file is /etc/zaptel.conf line 4: Unable to read Zaptel version information. Zaptel

Hi all, i've installed AMP and Asterisk following the INSTALL file and i have a problem with the TDM04B with 4 FXO: [root@srvoip ~]# ztcfg -vv Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 03: FXO Kewlstart (Default) (Slaves: 03) Channel 04: FXO Kewlstart (Default)

All, I had a question about the JGR console and whether or not I can manipulate the location where line wrapping occurs. I have searched 'JGR' in the R listserve archives and attempted to find console manipulation on the JGR website to no avail and could use some direction. TIA, Bret As an example, the below output wraps every 4th value, leaving about 2/3 of the console empty. >

I have 2 TDM04b cards currently running in an asterisk at home box that I am ready to replace with the CVS version of asterisk. What I am looking for is thoughts / recommendations. I want to move this to a small form factor ( shuttle ) machine and was wandering what expeience / advice there was for this? I have seen the incompatible motherboard list at digium ( and in fact I think my current

I have a new asterisk system with a T1 card. It appears that running "ztcfg -vv " is required in order for asterisk to start properly. Is this correct? Are people adding this command to the asterisk startup script? Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi All; In dahdi: what we use instead of ztcfg -vv (that is existed /sbin/ztcfg -vv). ? Regards Bilal

Hi all, I'm installing two HFC pci card (both in TE mode), I don't have problem when load module, but whrn I give "ztcfg -vv", I see 6 the six channels that I configured, then my computer hang and I have to reboot it. (I'm using a VIA Epia-M 1000 with Via C3 processor) root@test:~# modprobe zaptel root@test:~# insmod /usr/src/bristuff-0.2.0-RC8n/zaphfc/./zaphfc.o