similar to: quadBRI form junghanns.net

Hey, anyone know if it's possible to receive faxes through a Junghanns bristuff quadbri card? In germany, currently I have faxes coming in on DID line into QuadBRI and then passing to Digium TDM400 (analog) and into faxmachine. But the reliability of TDM card is spotty, so I want to maybe just accept faxes in on ISDN card and save on asterisk system ...? keeping digital signal strong ...

Hello everybody, I've got Asterisk 1.2.4 running with two Junghanns QuadBRI cards using the qozap driver from bristuff 0.3.0-PRE-1l. One of the cards is running in TE mode, the other one in NT mode. Whenever I call into an empty MeetMe conference room on one of the NT ports or via SIP and hang up the call during the "you are currently the only participant in this conference"

Hi, we are trying to install Junghann's quadBRI into Dell PowerEdge 2800 system without success. I don't know if the issue can be that Junghann's card fits 32-bit slot and Dell PE 2800 has only 3 PCI-X 64-bit slots. Can this be an issue? We get "CRC errors for HDLC frame" when the card is initialized. Any idea what can be wrong? 1/ We use latest bristuff packages. 2/

Hi everybody I hope that somebody can help me with the following .... I have 2 quadbri cards 2 - 1t0 cards 1 pabx alcatel 4200 I would like to connect my asterisk to the alcatel , I installed bristuff 0.3.0-1p , loaded the zaphfc driver in NT mode configured zaptel and zapata , it works great. then I removed the 1 t0 card, added the quadbri loaded qozap : insmod qozap.ko ports=15 ( 4 ports

Hi, I have an asterisk box with a QuadBRI. I am close to make it work like I want: Incoming calls to SIP are OK, outgoing calls are quiet working thanks to Michael Sandee advices. My real problem is that my * box is freezing very often when I probe qozap (bri-stuff 0.0.2). I have tried two distribs (Debian Kernel 2.6, Mandrake 9.1 Kernel 2.4) and it always work for a few minutes and freezes. At

Hi List, I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6). I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4 and asterisk-1.2.17 When it's the time for ztcfg to do its job it complains with <ZT_SPANCONFIG failed on span 2: No such device or address (6)>

Hi all, i'm trying to install Asterisk with Junghanns QuadBri ISDN card: I have followed all the instructions, and when I run "|ztcfg -tvv" I get | | Zaptel Configuration ======================| SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02)

Hi, I'm using a revision 6822-enabled Dahdi-Tools (see https://issues.asterisk.org/view.php?id=13897) with a Junghanns QuadBRI. 1. Do I still need qozap driver ? If positive, how is it recommended to get it ? 2. Which line should be included in /etc/dahdi/modules to have the appropriate driver loaded ? 3. The process I'm planning to use is : A- Hand edit /etc/dadhi/modules,

Hi! Asterisk in Debian/Lenny claims to be bristuffed, not? At least the the Debian patch tracking system shows the bristuff-patches: [1] http://bit.ly/bRRHe7 We have a QuadBRI-Card and recently needed support from Junghanns.net but they refused telling us there is no bristuff installed because of the show version output: *CLI> show version Asterisk 1.4.21.2~dfsg-3+lenny1 built by pbuilder @

Hi all, I'm trying to get a junghanns QuadBRI to coexist in the same machine as a Digium TDM400P card (so I can run the ISDN lines in and bridge with analog phones plugged into the TDM). I'm having a problem loading the modules. If I follow the BRIstuff (0.3.0-pre-1l) install method.... it's to modprobe zaptel, then insmod qozap.o I'm on Debian 2.4.31. That works. But then I

Hi, I have a Junghanns QuadBri installed and seems to be detected and working correctly using the wcb4xxp driver All ports are configured as TE The problem is when I connect an ISDN line - the LED turns green and Dahdi status shows Alarm OK But when I try to make a call I get "All circuits are busy" cause 27 I have searched and web and tried numerous configs but it doesn't want to

I installed the QuadBri card in my * server. I'm installing * on a RedHat 9 server I run the install.sh file. So far no problems. If I try to start /sbin/ztcfg -v -c /etc/zaptel.conf I will see the following error: Zaptel Configuration ====================== SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 2: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 3: CCS/ AMI Build-out:

Hi, we are using asterisk with Junghanns QuadBri and some sip phones. 2 channels are configured in NT mode (ISDN PBX connected, internal ) and 2 channels are connected to the public ISDN network (bri-cpe). We use Bristuff 0.2.0 RC8C from Junghanns. When a call comes in from the public phone for a specific extension (Hotline Number), we initiate a parallelcall to some SIP phones and also to our

Hi, I'm very new to asterisk and managed to set one up in debian, I installed via apt-get the asterisk and asterisk-bristuff packages. I downloaded the bristuff source as well. I managed to get as far as loading the following modules: zaptel 199144 4 cwain,zaphfc,zttranscode,ztdummy But the problem now is that all channels that I try to configure gives me an error that

Morning Asterikians, I've just got my nice shiny quadBRI card, and it seems to be working very well - except for one little issue - CallerID. The card is currently connected to an ISDN2e line in P2P mode, and an S0 adapter on our existing alcatel PBX. The S0 connection recieves callerID and displays it correctly - the 2e line doesn't, and BT have said that CLID was enabled on the

Hi, I'll soon replace a Junghanns OctoBRI with a Junghanns QuadBRI. As both use wcb4xxp driver (dahdi 2.3.0, libpri 1.4.10.2 and asterisk 1.6.1), I'm planning to proceed this way : 1. Edit 2 versions of files /etc/dahdi/system.conf and /etc/asterisk/dahdi-channels.conf (one for each card). 2. Link current system.conf and dahdi-channels.conf to QuadBRI files. 3. Power PC off 4. Swap cards

- I'm not a Linux user i'm trying to get in it ... - Fedora core 1 - QuadBRI card bought from junghanns.net - We want to use the card in TE mode to connect to the TELCO - Downloaded BRISTUFF0.0.2(stable) latest from junghanss.net/asterisk - followed the instructions on voip-info.org - compiled everything still got the error when "make load" in qozap : insmod ./qozap.o

Hi. I'm running some asterisk boxes on different sites, some equipped with a couple of ZapHFC cards, others with Junghanns quadBRI cards. All boxes were compiled with Asterisk 1.2.10 (libpri 1.2.3 zaptel 1.2.6) and bristuff 0.3.0 pre 1s, distribution is Fedora Core 4 with kernel 2.6.17.3 The cards are connected to Telecom Italia's NT1/NT1+ S/T lines; some of them are point-to-point,

Who is selling the quadBRI cards, which is everybody talking about? And how much does is costs? I'm looked on the site of junghanns.net, but there is no selling information. A seller in germany is favored.

Hi, Reading from www.voip-info.org, i can see that "Junghann's chan_capi is now part of bristuff <http://www.voip-info.org/wiki/view/Bristuff> , as of version 0.3.0-pre". What does that really mean ? Shall I understand I can share a Junghanns QuadBRI board between 2 CAPI-enabled software (like a 0.3.0-pre bristuffed Asterisk for instance) ? If positive, what are the pros and