asterisk users - Dec 2007 - Anyone here using JUNGHANNS.net douBRI 2.0 ISDN ?

Hi, 

I'm very new to asterisk and managed to set one up in debian, I
installed via apt-get the asterisk and asterisk-bristuff packages. I
downloaded the bristuff source as well. 

I managed to get as far as loading the following modules: 
zaptel                199144  4 cwain,zaphfc,zttranscode,ztdummy

But the problem now is that all channels that I try to configure gives
me an error that that device/address doesn't exist ..and only one
unconfigured device is displayed in zttool. 


Does anyone have any experience with this type of card? care to share
some tips? 


0c:02.0 ISDN controller: Cologne Chip Designs GmbH ISDN network
Controller [HFC-4S] (rev 01)
Subsystem: Cologne Chip Designs GmbH Unknown device b556
Flags: medium devsel, IRQ 5
I/O ports at ccf8 [size=8]
Memory at d9fff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2



Regards, 
Elijah

For the HFC-4S (4 bri channels) you need to qozap driver not zaphfc

Regards

Stelios S. Koroneos

Digital OPSiS - Embedded Intelligence
http://www.digital-opsis.com


Quoting Elijah <elijah.alcantara at gmail.com>:
> Hi, 
> 
> I'm very new to asterisk and managed to set one up in debian, I
> installed via apt-get the asterisk and asterisk-bristuff packages. I
> downloaded the bristuff source as well. 
> 
> I managed to get as far as loading the following modules: 
> zaptel                199144  4 cwain,zaphfc,zttranscode,ztdummy
> 
> But the problem now is that all channels that I try to configure gives
> me an error that that device/address doesn't exist ..and only one
> unconfigured device is displayed in zttool. 
> 
> 
> Does anyone have any experience with this type of card? care to share
> some tips? 
> 
> 
> 0c:02.0 ISDN controller: Cologne Chip Designs GmbH ISDN network
> Controller [HFC-4S] (rev 01)
> Subsystem: Cologne Chip Designs GmbH Unknown device b556
> Flags: medium devsel, IRQ 5
> I/O ports at ccf8 [size=8]
> Memory at d9fff000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [40] Power Management version 2
> 
> 
> 
> Regards, 
> Elijah 
> 
> 
> 
> 
> _______________________________________________
> --Bandwidth and Colocation Provided by http://www.api-digital.com--
> 
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
> 



----------------------------------------------------------------
This message was sent using IMP, the Internet Messaging Program.

On Monday 03 December 2007 18:58:22 Stelios Koroneos
wrote:
> For the HFC-4S (4 bri channels) you need to qozap driver not zaphfc
>
>-- 
I was using bristuff on a Junghanns quadBRI up to a few weeks ago, trying to 
upgrade the bristuff that had been installed 2 years was giving so many 
problems I installed mISDN. I was up and running in minutes and now all my 
ISDN PBXs are running chan_misdn with either Digium , Junghanns, AVM Fritz or 
Bewan cards. 

Dave Cotton

On Tue, Dec 04, 2007 at 01:25:53AM +0800, Elijah wrote:
> Hi, 
> 
> I'm very new to asterisk and managed to set one up in debian, I
> installed via apt-get the asterisk and asterisk-bristuff packages. I
> downloaded the bristuff source as well. 
> 
> I managed to get as far as loading the following modules: 
> zaptel                199144  4 cwain,zaphfc,zttranscode,ztdummy
> 
> But the problem now is that all channels that I try to configure gives
> me an error that that device/address doesn't exist ..and only one
> unconfigured device is displayed in zttool. 
> 
> 
> Does anyone have any experience with this type of card? care to share
> some tips? 
> 
> 
> 0c:02.0 ISDN controller: Cologne Chip Designs GmbH ISDN network
> Controller [HFC-4S] (rev 01)
> Subsystem: Cologne Chip Designs GmbH Unknown device b556
> Flags: medium devsel, IRQ 5
> I/O ports at ccf8 [size=8]
> Memory at d9fff000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [40] Power Management version 2
In addition to the fact that you need qozap (and not zaphfc) as
mentioned before), you also probably need a newer version of qozap than
the one included in Etch. 

Try getting zaptel and zaptel-source from the etch backports at
pkg-voip.buildserver.net/debian or from updates.xorcom.com/rapid .

Should work well with the Asterisk packages in Etch, though I haven't
really tested it.

-- 
               Tzafrir Cohen
icq#16849755              jabber:tzafrir.cohen at xorcom.com
+972-50-7952406           mailto:tzafrir.cohen at xorcom.com
http://www.xorcom.com  iax:guest at local.xorcom.com/tzafrir