similar to: Zaptel problem on BSD

Hello, is there a full guide to what kewlstart is supposed to do with FXO or FXS lines ? is it only applicable to one of the interfaces FXO -or- FXS but not both ? I asked earlier if FXS lines can be made to reverse polarity, and someone else pointed out that the chipset on the FXS ports seems to support it, perhaps the driver in the asterisk zaptel interface module needs to be modified to support

Hi.. I've got an asterisk setup with an X100P card installed.. I'm noticing that upon hangup, it takes a good 3 to 5 seconds before asterisk realizes the line has been hung up and drops the call.. this causes my SIP phone to continue ringing, and occassional phantom voice mail messages to be left.. I'm located in good old standard North America, with a regular Verizon residential

Hello I have installed my new E100P card in the same machin with two TDM04B cards. I have followthe instructions on http://www.digium.com/index.php?menu=configuration#T_E100P_PRI This is my zapata.conf span=1,0,0,cas,ami fxsls=1-15,17-31 dchan=16 fxsks=32-39 loadzone = us defaultzone=us I do *modprobe zaptel wct1xxp wcfxs ans seems to work ok. * But when i do ztcfg -vvv i got Zaptel

Hello, I am having problems configuring a TDM400P 4 Port FXO card with groundstart signalling. The box has 2 X100P's, 1 TDM04B and 1 TDM40B. I can configure it for loopstart and it works, just not groundstart, which I need for this installation. What am I missing? Thanks! Mark /etc/zaptel.conf #two X100P FXO Cards # fxsls=1-2 # TDM400P 4 Port FXO (TDM04B) fxsgs=3-6 # TDM400P 4 Port

I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*

*** Now you just need a "phone" or "station" (FXS) device and a method of connecting it. *** So... essentially I need to spend another $125 US on a Wildcard TDM400P so I can plug in an analog phone? On the X100P description it says: "The X100P supports FXS Loopstart and "Kewlstart" (Loopstart with far end disconnection supervision). It can detect ringing and

Hi All, I have just migrated from Asterisk 1.0.0 to Asterisk 1.0.5 and I have an X100P installed. The old asterisk was working, but now the new version isn't picking up any calls! However, I did notice that after installation, I performed modprobe zaptel and modprobe wcfxo and they worked fine, but when I executed ztcfg, I get the following errors: ioctl(ZT_LOADZONE) failed: Invalid

Hi List, I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6). I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4 and asterisk-1.2.17 When it's the time for ztcfg to do its job it complains with <ZT_SPANCONFIG failed on span 2: No such device or address (6)>

I am having trouble with chan_zap.so not loading. When I load it from modules.conf, Asterisk bails out without any error message. When I load it from the console, it just says "Unable to load module chan_zap.so" no matter what verbose level I am using. dmesg says: Zaptel Version: 1.4.4 Zaptel Echo Canceller: MG2 Freshmaker version: 73 Freshmaker passed register test Module 0:

Is anyone on the list using an Audiocodes gateway with asterisk and SIP? I'm looking at that platform, but I have a couple of issues: 1) Echo cancellation. The echo that I'm hearing with an X100P is unacceptable. Does the Audiocodes do better? 2) Line signalling. I'm using Kewlstart with the X100P, but it looks like the audiocodes uses loopstart only. How does this work with

Simple question that google hasn't helped much with (likely poor search terms) I just installed a Sangoma A200 with overall good results. Initial tests with both incoming and outgoing calls were very positive. Until I made a normal call that lasted more than 30 seconds. I setup the FXO with kewlstart signalling, and the outgoing call is never registered as 'Answered' and the dial

We're having issues with the FXO/FXS ports on our Digium TDM cards sporadically. I'm wondering if anyone else has had these problems, or if anyone can provide guidance diagnosing or fixing the issue? The symptoms are that the FXO and FXS ports "stop working", usually after 2-4 weeks of server uptime. When this happens, sending a (SIP) call to an analog phone on an FXS port

Hi All, Sorry if this has been around a millions times.. I have been off this list for a few months now.. I have installed the latest asterisknow (upgraded asterisk to 1.6 as well) and I am having a hard time getting my X100P and TDM400P working.. Its all new to me with dahdi because my old server is still running Asterisk 1.0.2 so there have been lost of changes.. Can someone point me in

Hello, I am trying the setup the TDM01B card. 1 FXO. I connected it to a regular home line. in the /etc/zaptel.conf, I have fxsls=4 In the /etc/asterisk/zapata.conf I have: signaling=fxs_ls language=en group=1 context=default channel => 4 When I start asterisk, I get this error: ERROR[10376]: chan_zap.c:6584 mkintf; Signaling requested on channel 4 is FXO Loopstart but line is in FXS

Hi All, I recently purchased the Asterisk Developer's Kit (TDM) to try out Asterisk. After following the directions in the Digium's FAQ topic entitled "Q. How do I configure my TDM40B and X100P?", I'm receiving the following error: WARNING[1074428608]: File chan_zap.c, Line 6748 (load_module): Ignoring rxwink ERROR[1074428608]: File chan_zap.c, Line 6692 (load_module):

Can someone please help me with my config settings for my TDM12B. I have got the FXS port to work fine, but I cannot get asterisk to startup with any settings for the fxo ports. It appears to be something related to the message "Signalling requested is FXS Kewlstart but line is in FXO Kewlstart signalling". However, I have tried what appears to be every possible configuration option. I

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

Hi everyone, I've just got my X100P card installed and working but there seems to be an issue with hang-up supervision. If I stuff a call out over the X100P card onto the PSTN that's fine. When I hang up the SIP phone the PSTN call ends. If I receive a call from the PSTN, it's answered and everything is ok until the remote party hangs up. Asterisk thinks the call is still active and

Hi there! I'm setting up a connection between Asterisk ver. 1.2.13 and a Harris 20-20 PBX. More less everything went fine, but the problem I have now is when dialing to the Harris PBX, it seems to pick up my call as soon as it reaches it. For example if from the Asterisk outgoing folder I dial an extension, say 100, and play a prompt as soon as it is picked up, the promt is beign played as

Dear All I have a problem with a TDM400 card with 4 x FXS modules. The card carries extensions only and there are no incoming lines. I can make a call to the extension on this card with no problems. However, when I try and call out I just get a busy signal. I also get an error message (as shown at the bottom). Is this a problem? Configs below: [root at asterisk etc]# more zaptel.conf