similar to: Error in Zapata Config?

I get the following errors when starting Asterisk. == Parsing '/etc/asterisk/zapata.conf': Found Feb 19 21:14:35 WARNING[10440]: chan_zap.c:920 zt_open: Unable to specify channel 1: No such device Feb 19 21:14:35 ERROR[10440]: chan_zap.c:6860 mkintf: Unable to open channel 1: No such device here = 0, tmp->channel = 1, channel = 1 Feb 19 21:14:35

Hello list , I?m putting to work a new asterisk box. I?m running * 1.0.3 with (one ) Wildcard TDM ( 2FXS* 2FXO) and (one) E-100P. Both boards are working well. ztcfg don?t show me any error. zttool list both cards as "OK" But when i run asterisk on verbose mode i get those errors : [chan_zap.so] => (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf': Found --

Hi all, I have a problem with the cvs head zaptel library: I cannot update my zapata.conf into asterisk when I issue the reload command from the CLI prompt; only when I stop and restart the asterisk service. The system sends the following message: Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364 setup_zap: Ignoring switchtype Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

Hi all, We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap modprobe wcfsx then the ztcfg output this: Zaptel

Hi all, this time with the complete configuration files... We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap

Hello all, This is my first post to this mailing list. I've been following the development (not as a developer, but as an interested user) of Asterisk for over a year now. It's only in the last month that we've decided to give it a try (hey, might as well...everything else we use is open source). We ordered a TDM11B (1 FXS, and 1 FXO). The card and Asterisk install was uneventful.

(Sorry of this appears in the list twice, but I wasn't sure if it was blocked or not) Hi there, I'm having a problem with my TDM-400P which has been working like a charm up until very recently. It started to fail last week, and so I was hoping someone could illuminate me with some information as to why. Its configuration is as follows: ------------ FXS (green) module is in position 1,

I have a Digium TDM400b11, 1FXO [port2] & 1FXS [port 1] When I reload the chan_zap I get: [chan_zap.so] => (Zapata Telephony w/PRI) == Parsing '/etc/asterisk/zapata.conf': Found Apr 9 22:39:36 ERROR[3541]: chan_zap.c:10388 setup_zap: Signalling must be specified before any channels are. Apr 9 22:39:36 WARNING[3541]: loader.c:414 __load_resource: chan_zap.so: load_module

Installing DevkitLite hardware (Very similar to John Lange's post on Tue Oct 08 2002) I cannot get anything to work on the phone connected to the s100u. I dont know what to do. Can someone please help me? I used the sample configuration files from digium documentaion that was supposed to be "sane" defaults for the kit. Very similar to John Lange's post on Tue Oct 08 2002 Here

I am trying to reconfigure an asterisk box that was using an HFC-S card with bristuff but is now using 2 analog lines therefore I want to use the TDM02B to connect to two POTS lines. The TDM02B has 2 red modules. I have this in /etc/zaptel.conf loadzone=nl defaultzone=nl fxsks=1-2 I have /etc/asterisk/zapata.conf signalling=fxs_ks echocancel=yes echocancelwhenbridged=yes echotraining=400

Dear All I have a problem with a TDM400 card with 4 x FXS modules. The card carries extensions only and there are no incoming lines. I can make a call to the extension on this card with no problems. However, when I try and call out I just get a busy signal. I also get an error message (as shown at the bottom). Is this a problem? Configs below: [root at asterisk etc]# more zaptel.conf

I reloaded my asterisk and found some red lines flushing by. When I stopped it I see: WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring signalling WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring echocancelwhenbridge WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring echotraining Reconfigure channel 1, FXO Kewlstart signalling Reconfigure channel 2, FXO Kewlstart signalling

I'm not sure if I have a configuration problem or not. I am unable to dial out. When I try to dial in I can hear the phone ring on the dialling phone but Asterisk does not register anything. In zaptel.conf I have loadzone = au defaultzone=au fxsks=1 In zapata.conf language=au context=from-pstn When I do: zap show channels I get: Chan Extension Context Language

Can someone please help me with my config settings for my TDM12B. I have got the FXS port to work fine, but I cannot get asterisk to startup with any settings for the fxo ports. It appears to be something related to the message "Signalling requested is FXS Kewlstart but line is in FXO Kewlstart signalling". However, I have tried what appears to be every possible configuration option. I

I am getting quite frustrated today, so please bear with me. I just installed Fedora Core 4 (was running RedHat 9 with a working Asterisk) now my Fedora does not appear to be recognizing my X100P (clone) at all. Hardware browser just shows them as unknown device. driver: hisax So, of course, my zaptel drivers do not work and therefore my asterisk does not work. any help would be greatly

I'm having a problem defining my channels Here is my zapata.conf ----------------------------------------------------------------------------------------------------- ; Zapata telephony interface ; ; Configuration file [channels] ; rxwink=300 ; Atlas seems to use long (250ms) winks usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes

Greetings all, I've just put two X100P cards to my box and despite trying everything I can find on the web, I can't get the second one to work. I've edited /etc/modules.conf so that ztcfg doesn't run automatically. To start, I run: /sbin/modprobe zaptel /sbin/modprobe wcfxo /sbin/ztcfg /sbin/modprobe ixj and ztcfg says: ZT_CHANCONFIG failed on channel 2: No such device or

Hello, I am trying the setup the TDM01B card. 1 FXO. I connected it to a regular home line. in the /etc/zaptel.conf, I have fxsls=4 In the /etc/asterisk/zapata.conf I have: signaling=fxs_ls language=en group=1 context=default channel => 4 When I start asterisk, I get this error: ERROR[10376]: chan_zap.c:6584 mkintf; Signaling requested on channel 4 is FXO Loopstart but line is in FXS

Feel free to hit me with a cluestick; maybe it will jar something lose... I'm running a stock *@home 0.6 install and after four days of excrutiatingly annoying debugging, I finally came across the obvious problem. The zaptel driver is reading /etc/zaptel.conf; which by default configures one FXS Kewlstart channel. Asterisk, according to "full" log, will see the first channel, then