similar to: Re: Asterisk-Users Digest, Vol 10, Issue 114

Hi All i'm using sangoma card. connected to E1, my wanpipe file as #================================================ # WANPIPE1 Configuration File #================================================ # # Date: Fri May 27 00:25:04 GMT+7 2005 # # Note: This file was generated automatically # by /usr/sbin/wancfg program. # # If you want to edit this file, it is # recommended

Hi Folks, I'm have Asterisk version 1.2.1 with a A101 PRI card. I'm working with the CLEC to bring up the PRI and inbound calls are hanging up at his end after a few seconds. I ran PRI debug but it only gives me minimal insight. " Ext: 1 Cause: Unknown (16), class = Normal Event (1)" He ran a trace and the only difference he is seeing is a "ISDN interface explicitly

Hi All I have problem with LIBMFCR2 for once Exchange I using Sangoma card, the firstly. my ssystem run successful with MFCR2, connected to E10 (Acatel Exchange), after that, i move connection connect to EWSD (Siemens), my system don't work. error protocol R2. my system: Asterisk CVS 1.1.X LibMFCR2 pre.005 and unicall-pre.005 this's my setting and my setting wanpipe1.conf

I'm using Asterisk 1.4.5 (will try 1.4.6 on Thursday, but I don't see anything in the changelog after the 1.4.5 release dealing with distinctive ring), zaptel 1.4.3, and wanpipe 2.3.4-10 with a Sangoma A200 card. I enabled usedistinctiveringdetection in zapata.conf. However, on the Asterisk console, the output I get is: -- Detected ring pattern: 0,0,0 It would appear that Asterisk is

Hi, I've already tried this in a squid list, but no response so maybe my problem is related to my squid conf. I'm setting up a squid proxy to auth against our 2003 ADS I have ntlm working so it authenticates both transparently to the user and using domain\username login. My Problem is getting squid to auth with just the username not requiring the domain\ part. The docs say I need

Hello, We have an Asterisk 1.0.9 machine with a Sangoma A101 card fitted, it is connected to a Telstra OnRamp E1 in Melbourne, Australia. The problem we are experiencing is extreme echo and clicking noises. These are only audible to the calling party, e.g. the person calling in from the PSTN to Asterisk via the E1, the person on the SIP handset cannot hear any echo or clicking, only the

I have used asterisk-1.4.14, zaptel-1.4.7, chan_ss7-1.0.0 on FC7 all went okay. using sangoma a104dx on both machine. I followed the write up on http://www.voip-info.org/wiki/index.php?page=Asterisk+ss7+setup I have the cross over cable between them. however, wanpipe shows connected but the signaling link does not align. i have my configs for host A ##wanpipe1.conf [devices] wanpipe1 =

My Sangoma Experience in Asterisk: Followup 2005-05-06 original review can be found at: http://astguiclient.sourceforge.net/Sangoma_experience.txt It's now been a month since I finished my last round of tests with the Sangoma A104u board in Asterisk. I have had a lot of conversations with the guys at Sangoma about how my system runs so that they could set up their test systems to try to

I've replaced 2XTE110 with an A102 with echo cancellation specifically to deal with echo problems. However, user feedback has indicated to me that on some calls (not a lot, but some) the call is unusable, with audio artifiacts, described by one user, as: "very bad phasing reverb & feedback (from my rock & roll days)". This is quite intermittent, as in most cases, the user

Does anyone have any experience ith configureing the sangoma A102 card for testing using a e1 cross cable i've configured and installed the cards properly even the lights on the card are green which proves that my cross cable is properly built too. my problem is with asterisk which gives me these errors PRI got event: HDLC Abort (6)on Primary D-channel of span 1 PRI got event: HDLC Bad FCS

I have a system that I am trying to get a port on a Sangoma A104d card connected to an Adtran 850 with 5 FXS modules and 1 FXO module. A problem I am having is figuring out what cable should be used from the port on the Sangoma to the JP2 port on the Adtran. Tried was a cross-over T1 (1->4, 2->5, 4->1, 5->2) as well as a straight T1 (1->1, 2->2, 4->4, 5->5). Neither one

Hello, All. I am currently running a test configuration for the telephony engineer here. I have two Dell PE servers, each with 2 A108 Sangoma T1/E1 cards. Here is a rough drawing: Ameritec Call Generator 8 T1 ISDN/PRI lines ---> Asterisk ---> Asterisk ---> Ameritec Call Generator Sangoma A108 Sangoma A108 Terminating 8 ISDN

Here's my planed setup : PRI from telco <--> (port 1 of A104d) * (port 2 of A104d) <--> PM3 The PM3, for those who don't know is lucent's portmaster RAS dial-up router. I had setup asterisk, zaptel, libpri, wanpipe (as I have sangoma's cards). In wancfg, I have port 1 as TDM_VOICE, with hardware echo on, span 1. Port 2 is TDM_VOICE, without hw echo, Clock as

Hi all, I've done this a few times with other PBX's but swyx has stumped me! I'm having some trouble getting Asterisk connected to a Swyx system using a sangoma A104dx... currently the setup is: BT <-> Swyx The above setup works fine... what i'm trying to achieve is BT & SIP Trunks <-> Asterisk <-> Swyx I have connected to our BT (2 x ISDN30 UK) with

Hi, after many issues we finally managed to make our system do outgoing calls with perfect quality. However I cannot detect *any* form of incoming call. when I use an outside phone to call the E1 connected to the sangoma a102, I instantly get a fast busy tone. My /etc/zaptel.conf is: loadzone=us defaultzone=us #Sangoma A102 port 1 [slot:1 bus:4 span: 1] span=1,0,0,ccs,hdb3 bchan=1-15,17-31

I've got a system where I'm integrating a Nortel Option 11c with a Trixbox 2.0.0 system using a Sangoma A101 T1 card. (Running on a Dell PowerEdge 350) We've got things mostly up and running and all seems well... except... If I call from a SIP extension (X-lite soft phone) dialing 9xxxx where xxxx is an extension on the Opt 11, the call goes through to the Opt 11 but I have terrible

Do you have any extension in default context of your extensions.conf file to accept incoming calls ? It must be something like; exten => 12345678,1,Answer() exten => 12345678,2,Playback(Welcome) ... 12345678 = The DID number you are calling to reach E1 Idris -----Original Message----- From: Erick Perez [mailto:eaperezh at gmail.com] Sent: Thursday, July 26, 2007 7:03 AM To:

Hi, I am trying to validate a setup with a sangoma A116 card (16PRI in one card). I currently have two machines set up, each with a sangoma A116 card. Those are interconnected with crossed PRI cables. One of them is in NT mode, the other in TE. The ports are configured in E1 mode, asterisk is all set up and I can make calls between them, filling up all 480 (16 * 30) channels. Now, I learned

I am having a problem trying to get a Sangoma A101 to work with Unicall. I have installed the sangoma drivers and everything seems to be well but when I try to run ztcfg I get the following error: CAS signalling on span 1 conflicts with HDLC with FCS check on channel 16. Here is my /etc/zaptel.conf # MFC/R2 normalmente no usa CRC4 span=1,0,0,cas,hdb3 cas=1-15:1101 dchan=16 cas=17-31:1101

Hi all, My problem boils down to these errors: ... Unable to create channel of type 'ZAP' (cause 34 - Circuit/channel congestion) == Everyone is busy/congested at this time This is triggered by lines in extentions.conf such as: exten => _X.,1,Dial(ZAP/g1/${EXTEN},,W) The system is CentOS v5.2 with Asterisk 1.4.23 (druid-asterisk-1.4.23.1-2), a Sangoma A104