similar to: Can't Dial Out with TDM04B

Hello all, I am having a serious problem installing my * with a TDM04B. I made everything work, call are coming in and going out including using a GSM Box in channel Zap/2-1. I did setup voicemail like this on extensions.conf: [incoming] exten => s,1,Dial(SIP/2246,20) exten => s,2,Wait,2 exten => s,3,Voicemail(u${ME}) exten => s,4,Hangup exten => s,102,Wait,2 exten =>

I would like to install a TDM04B with Asterisk@Home 2.4 and Asterisk@Home 1.5 but I didn't find documentation about this installation. Thanks in advance, Nelson -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060206/85ff5252/attachment.htm

I already have one Digium TDM04B installed in my server working fine. I just received 2 more so I did added them to my server. When I booted again linux told me that it found new hardware I said ignore. Then I log in as usual. I did ztcfg -vv to see if it sees 12 channels now instead of 4 but it only see 4. So then I did again modprobe zaptel, then modprobe wcfxo and wcfxs hoping it would see

Hello, I have installed asterisk version 1.2.12 and latest zaptel modules. but i can see some IRQ conflicts on the server. iam uisng two TDM04B cards. according to my previous knowledge on asterisk verison 1.07 asterisk has given lot of erros when starting if you have assigned the same IRQ number to any other device. My question is new releae version 1.2.12 has resolved the IRQ issue ?? TDM04B

Hi, I just received in the mail my TDM04B card and put it in the computer, now the computer won't even show the video card bios or the post screen. From the digium website I could not find any specific requirements for the pci card, like 32 or 64 bit slot. The motherboard for the computer I put it in is an Asus A7V333 with PCI 2.2 compliant slots. I am thinking that maybe I just got a dud

I'm installing my first Asterisk server. I have a TDM04B card installed in my asterisk server (4x FXO ports). I have 5 Cisco IP phone 7960 working fine on asterisk using SIP. My configuration to receive call is working as expected meaning anyone calling on one of the 4 FXO ports is answer by asterisk and asked to enter the extension of the person to reach and then it is transfer on the

Hi, A week or so ago I wrote about the problems I was having using a Digium TDM04B card in a Dell PowerEdge 750 IU running Fedora Core 1. Digium steadfastly indicates their card won't work in any PowerEdge 650, 700 and 750 series machines "do (sic) to a failure in interrupt handling between the pci bus and the card." My question to the list is: for those of you using a TDM04B

Hello, I have installed asterisk version 1.2.12 and latest zaptel modules. but i can see some IRQ conflicts on the server. iam uisng two TDM04B cards. according to my previous knowledge on asterisk verison 1.07 asterisk has given lot of erros when starting if you have assigned the same IRQ number to any other device. My question is new releae version 1.2.12 has resolved the IRQ issue ?? TDM04B

Hi, I am just trying to figure out how to setup a TDM04B card for incoming/outgoing calls. I have 4 lines, which are provided as a rotary trunk group, currently hooked into a Nortel system, which asterisk will replace. I have setup a Dell 1800 (Tower) system with the TDM04B card, which seems to work. The question is how do I set it up that all 4 lines are part of a trunk group, such that

I have installed Digium TDM04B with the latest CVS. However I have encountered following problems: 1. When it dials out, many times the digits are not properly recognized by telco as I hear the announcement "please check the number and dial again" although I see on the screen that the dialed number is correct. 2. When the call is forwarded outside, with something like exten =>

Hi, After days tinkering with this digium card (TDM04B), I notice that this card has a slow response in detecting ring signal from pstn and hanging up when the call is over. The delay can consume up to several seconds... Is this normal? Best regards, Stevanus

Hello I am struggling to get my TDM04B working. Just to rule out a hardware problem how can I check that the hardware works? How can I then check that the drivers are loaded correctly? Angus -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050620/470458c6/attachment.htm

Hi; Can I use two TDM04B in one asterisk box with asterisk@home? Thank You Onemli not : Bu e-mail iletisi, sadece adreste belirtilen kisi veya kurulusun kullanimini hedeflemekte olup, mesajda yer alan bilgiler kisiye ozel ve gizli olabilir, yasalar ya da anlasmalar geregi ucuncu kisiler ile paylasilmasi m?mk?n olmayabilir. Mesaji alan kisi, mesajin g?nderilmek istendigi kisi veya kurulus

I just install a Digium TDM04B card. I created 4 separate Zap channels and one outbound routing containing zap channels from 1 to 4. If a phone line is plug in Zap/1 then works fine, but if I unplug phone line from Zap/1 (simulating fail) the system keep dialing out on Zap/1, even with no dial tone; Only if Zap/1 is busy it will use Zap/2. There is any work around or different setting to avoid

Hello I have installed a TDM04B and disabled any devices not required in my PC. (TDM04B is analog card with 4 ports to plug into telephone co lines). I am running this version of * Asterisk CVS-HEAD-01/10/05-02:11:15-AstLinux built by root@ls on a i686 running Linux As you see below the wctdm module is loaded: pbx root # lsmod Module Size Used by binfmt_misc 12296 1 - Live

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: VoIP.gif Type: image/gif Size: 17666 bytes Desc: 1197705770-VoIP.gif Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20060213/7ca1c4ac/VoIP.gif

Hi, Some weird problem (or I'm too sleepy) happens with a tdm04B revision G (4fxo) Steps: modprobe zaptel modprobe wctdm ztcfg -vv /etc/zaptel.conf fxsls=1-4 # TDM04B defaultzone=us loadzone=us /etc/asterisk/zapata.conf signalling=fxs_ls group=1 context=incoming channel => 1-4 modprobe zaptel and wctdm load fine, however ztcfg -vv shows: 0 channels configured Im using centos 4.4 with

I have a TDM04B installed that isn't working 100% with Asterisk. I'm using the cvs-head of the zaptel drivers and asterisk with FC3 on a 2.6 kernel. I have successfully created a call on one of the channels, but there are a few problems. Even on channels with no analog line connected to them, after a few seconds (without reporting ringing) Asterisk will report that the call has been

Hi: I had an fxo card from Digitnetworks and it was working fine on my Asterisk box. I then replaced it with TDM04B. I changed the zaptel and zapata to include the four channels. When I run ztcfg, I get configuration errors: Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04:

Hi all, i have installed two digium cards on my asterisk box a TDM04B & TDM22B. The channels are configured as show below: Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: FXS Kewlstart (Default) (Slaves: 04) Channel 05: FXS Kewlstart (Default) (Slaves: 05) Channel 06: