similar to: NetHDLC + PRI

I have my Linux 2.6 kernel with the necessary HDLC config and also recompiled zaptel accordingly. On modprobe, I get: Found a Wildcard: Digium Wildcard T100P T1/PRI Debug: sleeping function called from invalid context at mm/slab.c:2000 in_atomic():0[expected: 0], irqs_disabled():1 [<0211e605>] __might_sleep+0x82/0x8c [<02144643>] kmem_cache_alloc+0x1d/0x57 [<42ad7a2c>]

Hello all, My set up is a fractionated t1, with 1-6 voice channels, 21-24 data channels. I have a t100P installed in a amd 1500 with 512meg. Question: In order to set up the data channels, is the following correct? 1) compile new kernel with generic hdlc support 2) compile hdlc from hq.pm.waw.pl/hdlc 3) uncomment KFLAGS+=DConfig_ZAPATA_NET in zaptel makefile 4) compile zaptel, 5 compile rest

SYNOPSIS Erratic red alarm T1 PRI on asterisk, but zttool running concurrently during alarm shows no errors, irq misses, or alarms, on any span. Using asterisk and quad Digium T405P, configured as follows: Span 1 connects to ISDN PRI (fractional 8 B channels, D channel 24). Span 2 connects to T1 Mux and analog stations. Span 3 connects to ISDN PRI Nortel BCM hybrid key system digital trunk.

Hi All I have problem with LIBMFCR2 for once Exchange I using Sangoma card, the firstly. my ssystem run successful with MFCR2, connected to E10 (Acatel Exchange), after that, i move connection connect to EWSD (Siemens), my system don't work. error protocol R2. my system: Asterisk CVS 1.1.X LibMFCR2 pre.005 and unicall-pre.005 this's my setting and my setting wanpipe1.conf

Hello! I am trying to set up multi-link PPP using two T100P cards in one machine, and 1 T405P card (the 4-port one) in another machine. I have previously been able to get PPP working between the two T100P cards in separate machines.... The 4-port card seems to be my problem currently. I am trying to use the tor2 driver (from a fresh CVS download this morning). When I load the driver (or run

Hi Since Im using the mISDN drivers and no zaptel stuff, I had to install ztdummy to get MeetMe to work. Well, that was the plan. Now, after getting the latest zaptel version over CVS (Im using Kernel 2.6), uncommenting all the modules except ztdummy in zaptel.sysconfig file and compiling this by "make", "make install" and "make linux26", I rebooted and

Hy, I'm working with asterisk 1.2.4 and zaptel 1.2.4 With these version an the options in zapata.conf: answeronpolarityswitch=yes hanguponpolarityswitch=yes I don't detect polarityswitch. When asterisk reloads I see in CLI: May 10 00:44:27 WARNING[14639]: chan_zap.c:10876 setup_zap: Ignoring answeronpolarityswitch May 10 00:44:27 WARNING[14639]: chan_zap.c:10876 setup_zap: Ignoring

I reloaded my asterisk and found some red lines flushing by. When I stopped it I see: WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring signalling WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring echocancelwhenbridge WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring echotraining Reconfigure channel 1, FXO Kewlstart signalling Reconfigure channel 2, FXO Kewlstart signalling

When I reload the asterisk I get the following warnings: Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring switchtype Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring signalling Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring rxwink Everything works fine as far as I know, I can dial and complete calls. So why am I getting this

Ok so it seg faults when I try to dial out through IAX(voiptalk.org), ofcourse it doesn't if I remove allow=speex :P ---- (gdb) run -c Starting program: /usr/sbin/asterisk -c [Thread debugging using libthread_db enabled] [New Thread 16384 (LWP 28283)] [New Thread 32769 (LWP 28285)] [New Thread 16386 (LWP 28286)] [Thread 16386 (LWP 28286) exited] [New Thread 32771 (LWP 28287)] Asterisk

When I reload the config, I see this error in the CLI. However, I don't see what I have done wrong: == Parsing '/etc/asterisk/zapata.conf': Found May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring signalling -- Reconfigured channel 1, FXO Kewlstart signalling May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring signalling -- Reconfigured

I am running RedHat Fedora Core 3 with their "kernel-2.6.10-1.741_FC3" kernel, and if I use nethdlc in zaptel.conf, when I run ztcfg I get the message: ZT_CHANCONFIG failed on channel 11: Function not implemented (38) Does anyone have ideas on how I can work around this issue? T1 channels 1-10 are voice, 11-24 are data (second board isn't used at the moment). Here is my

Hi all, I have a problem with the cvs head zaptel library: I cannot update my zapata.conf into asterisk when I issue the reload command from the CLI prompt; only when I stop and restart the asterisk service. The system sends the following message: Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364 setup_zap: Ignoring switchtype Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364

hi all iam using ztdummy driver after my call end , when i look at debug mode in cli i get this errors --- (0 headers 0 lines) Nat keepalive --- -- Reloading module 'chan_agent.so' (Agent Proxy Channel) == Parsing '/etc/asterisk/agents.conf': Found -- Reloading module 'chan_local.so' (Local Proxy Channel) -- Reloading module 'chan_zap.so' (Zapata

Hy, I'm writing from Spain. I have the 1.2.4 asterisk version and 1.2.3 zaptel version. I've heart that this asterisk's version detects correctly de hang up of PSTN, but in my case this thing doesn't happen. Moreover, my asterisk sends the next messages in the CLI: Feb 21 15:03:13 WARNING[10363]: chan_zap.c:10876 setup_zap: Ignoring signalling Feb 21 15:03:13 WARNING[10363]:

Good day all We got a Wildcard TE110P I installed linux,zaptel,libpti and asterisk I coped over my zaptel.conf and zapata.conf from a previous E100P config But when I try to start asterisk it gives error not bying able to load zap channles: == Parsing '/etc/asterisk/zapata.conf': Found Jan 10 08:17:18 WARNING[-1084595552]: chan_zap.c:9308 setup_zap: Ignoring switchtype Jan 10 08:17:18

Hello everyone, We have recently turned up a new T1 from McLeod (Midwestern CLEC). It is configured like so: /etc/zaptel.conf: loadzone=us defaultzone=us span=1,0,0,esf,b8zs ;(also tried 1,1,0,esf,b8zs) bchan=13-23 nethdlc=1-12 dchan=24 /etc/zapata.conf: switchtype=national context=pri-in signalling=pri_cpe group=1 channel => 13-23 I can get hdlc0 (and pvc0) up just fine after the

Em (20:59:21), Asterisk Users Mailing List - Non-Commercial Discussion escreveu: >On Tue, Jun 21, 2005 at 08:09:52PM -0300, Alessandro wrote: >> >> Does Somebody know why no load modules to FXS? I used zaptel-1.0.7 >> version. > >What color are the modules? >Post your /etc/zaptel.conf > >-- >Mike Mike, The color is green, red ans bluw. Link

Hiya all, I have had no end of trouble trying to get my A101 E1 card working on a new asterisk installation. The sangoma tech people have ignored my emails about this. All the installation of wanpipe seems to go ok, and zaptel. it all installed compiled and does all the wanpipe hwprobe exactly as documented. Asterisk compiled ok, but when I run it give me Jun 27 11:12:18 ERROR[10528]:

I'm trying to use ztcfg with the following zaptel.conf: span=1,1,0,esf,b8zs bchan=1-4 nethdlc 5-23 dchan=24 and I get "ZT_CHANCONFIG failed on channel 5: Function not implemented (38). This is on Debian 2.4.26. I have hdlc compiled as a module. Should hdlc be compiled into the kernel? Does anyone see a problem here? Thanks, -- Michael Welter Introspect Telephony Corp. Denver,