Displaying 20 results from an estimated 3000 matches similar to: "Adit 600 for asterisk"
2004 Dec 09
3
Adit Asterisk Cabling Connundrum.
I am hoping to replace my Nortel 8x24 switch with
Asterisk. Right now my cabling comes from my outside
phone box into my office and into a punchdown block
and leaves the punchdown block as an amphenol
connector which currently plugs into the Nortel
swicth. A second amphenol connector them plugs into
the switch and extends to another punchdown block that
I believe carries the lines throughout the
2004 Dec 09
3
possible OT - ADIT 600 question
Say I get an ADIT 600 with two FXS8A and one FXO8A from ebay.
a. Is it good for Asterisk?
b. How do I connect the extensions and lines to it? Do I need a special
jack? Can I get that jack in every corner?
c. where can I find help for configuring it?
d. what kind of backup does it have? Does it need to be reconfigured
after a power outage?
Shoval Tomer,
IT Manager,
SofTov Advanced Systems, Ltd.
2005 Jan 28
1
adit 600 fxo ports immediately "answers" outgoing calls (even if not connected to line)
I have an adit 600 with an fxo card connected to a digium T1 card.
If I try to make an outgoing call and the T1 cable is disconnected,
asterisks returns congested like it should.
But, if the adit 600 is connected to the T1 card, the adit 600
immediately "answers" the call even if there are no physical
lines attached. I even removed the fxo card and the adit
600 still
2004 Apr 15
2
TE405P + Adit 600 and FXO module - should this work?
Folks,
I'm experimenting with bringing multiple (8) analog lines from our local
telco into a Carrier Access ADIT 600 channel bank with an FXO module, then
having this talk to Asterisk via the T1 TDM controller on the ADIT and a
TE405P card.
I don't know if this will work well (ie: give me decent echo cancellation,
call disconnect supervision, caller ID etc) but I haven't had much
2006 Jun 03
2
ADIT 600 <=> Asterisk Help
I've been reading the Google searches trying to understand how to tie
together Adit 600 to Asterisk to provide 2 way service. I'm about blind
from reading.
I assume, the answer is using MGCP between the boxes. However, the examples
I found don't really explain fully enough to know how to modify examples to
work for me.
I'll have in the ADIT with T1's. There is a CMG and
2005 Jan 27
2
Adit 600
Has anyone had any success using the Adit 600 with the CMG card talking
MGCP to asterisk? I want to have a central asterisk server with 10 Adit
600's at various locations providing 24 FXS ports....
Thanks,
Isaac
2004 Dec 09
1
[OT] Adit 600 Question
Hi,
I'm using an Adit 600 Channel Bank with *. I love it and it works
really great for my FXS lines. One problem that I have with it (It's
really not a problem yet, but it's a potential one) is that I've
scoured the manaual for the Adit to see if there's a way to dump out a
config file from the bank so in the event of a power and battery
failure I don't have to type in the
2004 Apr 07
2
Problems with ADIT 600 - latency, loss, etc
I'm emailing this as the customer in this case, since my carrier appears
to be completely unable to solve this. A brief rundown of the problem:
- We have several voice lines going through the ADIT, of course into a
VoIP type of arrangement.
- Voice traffic will become choppy, even drop calls completely, at random
but quite often. Modem calls (which we needed unfortunately) are a joke.
-
2009 Mar 03
2
Asterisk analog DID with Adit 600
Hello All,
I'm trying to connect Asterisk to an Executone phone system with an
analog DID card and I'm hoping someone can help me figure out what I'm
doing wrong. The Executone DID card provides battery to the telco, when
the telco wishes to dial a DID it goes off-hook, waits for a wink from
the Executone and then dials the last three digits on the number with
pulse (as opposed
2004 Aug 24
3
Asterisk with Adit 600
Hello,
I am connecting Asterisk to an Adit 600 via a T100P. Unfortunately I am not able to get any lights on the T100P and the Adit 600 only shows red. I have already modprobed the t100p.
Has anyone successfully connected these before?
I've tried both a cross-over cable and a standard cat 5 cable, but I can't seem to get them to work.
Any suggestions?
Thanks!
Craig
2004 Jun 28
2
Adit 600 - Getting Dial Tone
Hello, I have an Adit 600 (3 FXS cards) hooked up to a digium T1 card in my
asterisk box. I 'connected' the slots to the a:1 T1 interfaces via the
command line. The slots (3 fxs) are configured with 'ls' signaling. I
configured the T1 card with the same line settings as the T1 interfaces on
the adit and I get green lights on both the T1 card and the T1 interface on
the adit (so
2007 Sep 03
1
ADIT 600 & CMG <=> Asterisk question
I've searched but can't find an answer as to how many MGCP paths can a
single ADIT/CMG card support? It appears it's only 24 ports, maybe 48.
What I'd like to do is install 6 Telco T1's into a single (or more) Adit
600 and route inbound calls towards asterisk. Can I have more than one
CMG in a single chassis?
Or maybe you know of a better way to connect T1's to
2004 Jan 13
3
How to Order Disconnect Supervision from SBC using Adit 600?
Can anyone help me with the term that SBC uses to refer to disconnect
supervision? I have an Adit 600 channel bank which has helped improve the
disconnect detection time down to about 8 seconds. This is still causing some
issues in particular with call progress enabled in * we are having a few
disconnects while calls are in session (about 2 reported in first 5 days of use).
I have talked both to
2006 Jan 12
2
Adit 600 and echo
I'm having issues with echo.
My setup is Polycom IP501 phones connected to an Adit 600 via T100P. 13
Lines going to the Adit.
All echo so far is on the local side (Employees hears own voice, but
only on some calls).
Watching the channel with ztmonitor, I notice that TXGAIN is pegged out
most of the time. RXGAIN is anywhere between 45 and 60%.
Is it safe to assume that playing around
2004 May 18
2
ADIT 600 Manual
I am trying to find a manual for the Carrier Access Adit 600. Does anyone
know where I might be able to find one?
Thanks
-Jon
--
Jon J. Brandon jon@monsoonretail.com http://www.monsoonretail.com
2005 Feb 21
2
Adit 600 MGCP configuration
I've finally got my Adit 600 and are configuring it right now.
But I have to say, there aren't much documentation for it.
I've setup MGCP and Asterisk seems to find it.
But all channels (40 FXS channels) are "Down"!
But the MGCP itself is "Up" according to the statistics.
I can't find any documents how to set each channel to "Up" in the CLI.
Any
2004 Nov 29
1
[Fwd: Re: Adit 600 channel bank in UK setting]
Jon,
I actually had some more discussions with Tim on this issue, and it seems that the channel bank
would still be a good option to choose for internal purposes. I would not see any other solution
than a channel bank to connect many 2wire phones into one asterisk box. I had a talk today with
Carrier Access, and it seems that the adit would do us fine. The fxs cards of the adit 600 are
2005 Oct 02
1
Adit 600 FXO card sound quality
I have an adit 600 with one fxo card connected to a Digium single span T1 card.
CallerID, disconnect supervision work perfect, however the users
complain that they have some sound quality issues, after testing it I
realized that whenever one is in a phone call they get like silence
between the sounds coming from the other party, almost like a cell
phone, in other words if there is no sound coming
2005 Feb 12
1
PLEASE HELP Adit 600 went kaput?
After months of setting up Asterisk. I completed the
final testing last night We would go live on Monday.
Or so I thought.
As I moved the Adit 600 back out of the way, sliding
it six inches. I noticed the major light was red as
were both T1 and T2 lights ( eventhough only one t1
port is being used ) -- I have no idea what these
lights mean or if they were lit before when things
were working.
2005 Jan 21
4
Adit 600 as VoIP router (MGCP) and Asterisk
Got at suggestion from CarrierAccess to use the Adit 600 as an VoIP router using MGCP IP protocol, instead of controlling it through an E1.
Have anyone tried this configuration? How does MGCP works? I've tried to search for it on Google, but I only find the protocol specification for it.
Is Asterisk fully capable of this? I can't find any documentatin covering the use of MGCP in Asterisk.