Displaying 20 results from an estimated 5000 matches similar to: "Sangoma A102 cards testing"
2007 Jul 26
1
Asterisk 1.2.23 and Sangoma a102 no incoming calldetected
Do you have any extension in default context of your extensions.conf
file to accept incoming calls ?
It must be something like;
exten => 12345678,1,Answer()
exten => 12345678,2,Playback(Welcome)
...
12345678 = The DID number you are calling to reach E1
Idris
-----Original Message-----
From: Erick Perez [mailto:eaperezh at gmail.com]
Sent: Thursday, July 26, 2007 7:03 AM
To:
2007 Jan 03
2
Sangoma A102 w/ EC module gets intermittent echo /audio artifacts
I've replaced 2XTE110 with an A102 with echo cancellation specifically to
deal with echo problems. However, user feedback has indicated to me that on
some calls (not a lot, but some) the call is unusable, with audio
artifiacts, described by one user, as: "very bad phasing reverb & feedback
(from my rock & roll days)". This is quite intermittent, as in most cases,
the user
2007 Jul 26
1
Asterisk 1.2.23 and Sangoma a102 no incoming call detected
Hi,
after many issues we finally managed to make our system do outgoing
calls with perfect quality.
However I cannot detect *any* form of incoming call. when I use an
outside phone to call the E1 connected to the sangoma a102, I
instantly get a fast busy tone.
My /etc/zaptel.conf is:
loadzone=us
defaultzone=us
#Sangoma A102 port 1 [slot:1 bus:4 span: 1]
span=1,0,0,ccs,hdb3
bchan=1-15,17-31
2006 Apr 10
3
E1 PRI problem with TE205P
Hi all,
I've setup a PBX in production environment last week but we have immediatly
find out drop conversations and lot of errors (in asterisk logs) like:
Apr 10 17:30:48 NOTICE[25154] chan_zap.c: PRI got event: HDLC Bad
FCS (8) on Primary D-channel of span 2
My configuration is:
Motherboard: SuperMicro P8SCT (Intel E7221 chipset)
Hypertrading and APIC enabled
CPU: P4 3GHz
Digium TE205P
2005 Feb 17
2
Sangoma A104 - D-Channel problem
Hello,
I have following problem with Sangoma A104 card:
CLI> pri show span 1
Primary D-channel: 16
Status: Provisioned, Down, Active
Switchtype: EuroISDN
Type: CPE
Window Length: 0/7
Sentrej: 0
SolicitFbit: 0
Retrans: 0
Busy: 0
Overlap Dial: 0
T200 Timer: 1000
T203 Timer: 10000
T305 Timer: 30000
T308 Timer: 4000
T313 Timer: 4000
N200 Counter: 3
NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI
2007 Aug 16
1
A102 card, BT ISDN30e, silence
Thanks to help on this list and Sangoma's support we have incoming and
outgoing calls passing through asterisk.
However both incoming and outgoing calls are greeted by silence.
I've noted our existing config below with our test extensions.conf.
Help much appreciated
Rory
Zaptel
-----------------------------------------------------------------------
loadzone=uk
defaultzone=uk
#Sangoma
2010 Mar 17
7
Asterisk DIES with no trace. PLEASE HELP!
Hello my friends
We are having seriously problems with our asterisk server, our versions are
as follows:
WANPIPE Release: 3.4.7
Asterisk 1.4.21.2
Zaptel Version: 1.4.11
libpri version: 1.4.10.2
The symptoms are very weird, the CLI stop working suddenly, a core show
channels shows MANY channels FREEZED, the incoming and outgoing calls stop
working, the internal calls stop working, in resume we
2010 Apr 01
2
Problem with Sangoma A104 and euroisdn pri
Hi all,
My problem boils down to these errors:
... Unable to create channel of type 'ZAP' (cause 34 -
Circuit/channel congestion)
== Everyone is busy/congested at this time
This is triggered by lines in extentions.conf such as:
exten => _X.,1,Dial(ZAP/g1/${EXTEN},,W)
The system is CentOS v5.2 with Asterisk 1.4.23
(druid-asterisk-1.4.23.1-2), a Sangoma A104
2007 May 18
2
TE212P octastic initialization failure
Hi,
I'm trying to get a TE212 working on a Dell PowerEdge 1850 running
Debian etch using the latest release of libpri (1.4.0), zaptel (1.4.2.1)
and asterisk (1.4.4). The initilization of the Octasic echo canceller
seems to fail when the wct4xxp module is loaded.
[...]
VPM450: echo cancellation for 64 channels
Failed to open chip, code 00103017!
VPM450: Failed to initialize
[...]
By looking
2004 Apr 30
1
Configuring Digium TE405P for use in Germany
Hello all,
I really checked voip-info.org but it still seems to be not very easy and I
just hope that there is anybody with a simular config.
We have one PRI (euroisdn with 30 channels) coming from the DTAG. The second
PRI should be connected to a Siemens Hicom 150E Pro Office PBX (was cheaper
than a channel bank :-)
Carrier ----S2M------ * -----S2M------Siemens
|
|
2006 Aug 28
3
lost packets when bridging zap and iax
We have a machine with a TE410P in it acting as a client to route calls
via iax2 to our central server,
caller --> ( zap -> iax ) ---> ( iax -> whatever ) --> called
client server
often the called can't hear the caller (both machines on public ip)
'iax2 show netstats" on client machine shows more and more dropped
packets on the
2004 Aug 13
11
asterisk in india
Does anyone know if the E1 cards that digium sells work in India. Also are
there any distributers for those cards in India. By E1 cards I mean E100P,
TE410P or TE405P
--
regards
Vikram (http://www.vicramresearch.com)
2007 Jan 03
0
Sangoma A102 w/ EC module gets intermittent echo/audio artifacts
I think you are absolutely right. The audio I heard earlier sounds exactly
like a timing issue. So:
wanpipe1.conf:
TE_CLOCK = NORMAL
TE_REF_CLOCK = 0
wanpipe2.conf:
TE_CLOCK = MASTER
TE_REF_CLOCK = 1
zaptel.conf:
span=1,1,0,esf,b8zs
span=2,0,0,esf,b8zs
I'm going to make this change and reload at lunchtime, I'll document it and
post it to the list if it works.
2007 Jan 04
0
Sangoma A102 w/ EC module gets intermittent echo/audio artifacts <--followup and resolution
Followup on this issue, it appears that using a single PRI's clock as the
master clock avoids clock drift between the PRI's and we get no more
artifacts. So, :
wanpipe1.conf:
TE_CLOCK = NORMAL
TE_REF_CLOCK = 0
wanpipe2.conf:
TE_CLOCK = MASTER
TE_REF_CLOCK = 1
zaptel.conf:
span=1,1,0,esf,b8zs
span=2,0,0,esf,b8zs
-----Original Message-----
From: Michael L. Young
2004 Aug 12
5
Question about TE405P
Hi all,
Does somebody know how I have to setup my TE405P ?
Is it correct my configuration below ? Otherwise, can somebody help me ?
Thanks,
Angel.
zaptel.conf
span=1,1,0,ccs,hdb3
span=2,0,1,ccs,hdb3
span=3,0,1,ccs,hdb3
span=4,0,1,ccs,hdb3
bchan=1-15
dchan=16
bchan=17-31
bchan=1-15
dchan=16
bchan=17-31
bchan=1-15
dchan=16
bchan=17-31
2006 May 11
3
sangoma A102 installation question
Hi!
I've went through the READMEs and could not answer this question:
During installation, the Setup program asks:
Would you like update/upgrade wanpipe drivers? (y/n)
For a pure Asterisk TDM installation - is it required to patch the
kernel or is this only when using the sangoma cards as WAN router?
regards
klaus
2005 Jul 28
1
how to loop E400P card to test ?Any help will be appreciated.
asterisk-users
Any help will be appreciated.
This card did not connect with E1 line
how to loop E400P card to test ?
now I loop the card.
span 1 ---span2
RJ45 pins
1--4
2--5
but show :
When calling ,showing error:
app_dial.c:764 dial_exec: Unable to create channel of type 'Zap'
Asterisk Ready.
*CLI> -- Registered SIP '2002' at 192.168.139.59 port 3289 expires 120
2004 Jul 29
6
Zaptel doesn't see remote hangup ? euro-isdn
Hi
Just received my spanky new TE405P today to replace my Cisco gateway...
After much fiddling (I forgot to switch it to E1) I got it to work and
everything "seems" to work perfectly on our ISDN PRI.
If I dial-in from the PSTN to a SIP phone, the call goes through and if I
hangup either the SIP phone or the remote end, the call gets disconnected
and destroyed
However, if I dial-in
2007 Sep 05
4
ztcfg error : TE110p error with " CAS signalling on span 1 conflicts with HDLC with ...
Dear All,
I'm integrating avaya commuication manager difinity ver 1.0 with asterisk
using B2B E1. following are the details of my H/W, zaptel configs and
software installed.
Digium TE110p
asterisk 1.2.19
cent OS 4.4
zaptel 1.2.18
libpri 1.2.4
etc/zaptel.conf
span=1,0,0,cas,hdb3
bchan=1-15,17-31
dchan=16
when i ztcfg -vvv im having this error message and the E1 is not getting up.
"cas
2006 Nov 16
1
Sangoma A101 gives 'no PRI configured on span 1' error
I upgraded from Tormenta2 to Sangoma A101. I followed the instructions, and
installation was successful. zttool, ztcfg, all show card is installed
properly. I copied the parameters from my old working zaptel.conf,
zapata.conf and zapata-auto.conf. Verified on Sangoma website that these
files are correct. Also configured wanpipe1.conf.
But doing all this didn't start the PRI channels. It says