similar to: Asterisk 1.0.5-BRIstuffed-0.2.0-RC5 caller id?

I have Asterisk 1.0.5-BRIstuffed-0.2.0-RC5 up and running. Everything seems to be running fine but after some time asterisk just goes crazy (even withouth any incoming or outgoing call activity perviously). If I leave the box up for some time * goes haywire and the console is flooded with this message: Ouch ... error while writing audio data: : Broken pipe At that time I can see that there

Hi list! I'm trying to get PrivacyManager working but for some reason it always thinks that CallerID is present (when it isn't). I get this on the console: == Primary D-Channel on span 1 up -- Accepting voice call from '' to '0711234567' on channel 0/2, span 1 -- Executing Ringing("Zap/2-1", "") in new stack -- Executing

Hi list! I'm using phones that emulate a Cisco 7940 with chan_sccp. When I was using Asterisk 1.0.5 (bristuffed) I never had any such message on the console. The phones do work. Is this a bug in chan_sccp or a feature of asterisk 1.0.6? Thx!

I hva ean HFC-S card in a box that I'm trying to get to work with bristuffed Asterisk 1.0.3. The box is an Athlon64 running a RHEL rebuild with a plain vanilla 2.6.10 kernel. I tried both APIC and NOAPIC mode. The installation went ok and does give output that seems correct SPAN 1: CCS/ AMI Buil-out: 399-533 feet (DSX-1) 2 channels and one D-channel Even though I've configured * to

Hi list! I have some strange problems with Asterisk 1.0.5-BRIstuffed-0.2.0-RC5. Very regularly asterisk seems to lose connectivity with the ISDN line. If you try to call in you get the information tone that the number is not in use. Outbound calls do stil work however. Unloading the modules and reloading them and start/stop asterisk will solve the problem. Another problem that occurs

After upgrading a CentOS 3.x box to CentOS 4.1 (both x86_64 with an Athlon64) I also wanted to get the latest bristuff. Unfortunately bristuff without florz causes the box to kernel panic within hours (console will complain about bad frame received something). It seems however that the florz patch will not work for x86_64 arch. Bristuff -0.2.0-RC8j compiles fine without the florz patch, but

Hi list! What exactly is the meaning / function of the pridialplan & prilocaldialplan? I've been trying to find out what the different possibilities for these settings are but couldn't find a clear answer. The possible parameters I could find are are : local,unknown,dynamic,national,international and maybe there are more? Thanks!

Hi list! I am installing an * box that will be installed on a site with KPN BRI ISDN in The Netherlands. I am using bristuff fron Junghanns. Does anybody know the correct settings for this? I will not have internet access there which makes it harder to google around on location. switchtype = euroisdn is pretty obvious but what about these settings: signalling = bri_cpe_ptmp ; p2p TE mode

I applied the florz patch but my problems remain. Now I get all sorts of weird errors on the console and I cannot make outgoing calls. Incoming calls work as expected. I am using a single HFC-S card with BRI. Any clue what these errors below are? Ri = 44651 TEI msg = 3 TEI = 7f Ri = 3800 TEI msg = 3 TEI = 7f Ri = 42399 TEI msg = 3 TEI = 7f Ri = 42409 TEI msg = 3 TEI = 7f Ri = 22078 TEI msg = 3

Hello, I've added a ZAPHFC card to my CAPI based system. Calls coming in via ZAPHFC do not forward the caller id to the SIP phones. Calls coming in via CAPI do forward the caller id to the SIP phones. Any and all help is greatly appreciated. The (hopefully relevant) conf file excerpts are: extensions.conf =============== exten => 807440,1,Answer exten => 807440,2,Noop exten =>

Hello, I have a problem with the Bristuffed version of Asterisk. I have tried Bristuff-0.3.0-pre-1m,n,o,p (Asterisk 1.2.6 to 1.2.7.1) but they all have the same problem it seems: The setup: A machine with a single hfc-s PCI BRI adapter running Gentoo 2.6.15. Asterisk 1.2.0 (BRIstuffed-0.3.0-PRE-1) installed and working perfectly. Grandstream gxp-2000 as a SIP phone, and a normal mobile

I'm using Asterisk 1.0.2-BRIstuffed-0.2.0-RC2b - when anyone picks up a call with '*8' - the call will drop after about 20 or so seconds. Is this a general problem with Asterisk 1.0.2? As this is the latest release that it appears Klaus-Peter Junghanns has for public consumption - is there anything I can patch for just this problem - or has Klaus-Peter Junghanns (or anyone else) been

Hi, I'm currently using chan_capi-cm-0.6, with the following capi.conf: [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 language=de [ISDN1] msn=8304490 incomingmsn=8304490 isdnmode=msn group=1 controller=1 softdtmf=1 context=demo echosquelch=1 echocancel=yes echotail=64 callgroup=1 devices=2 Each user has a different numer, e.g. 83044910, 83044911, 83044912 and so

Hello, I have a little problem with signalling. An E100p is connected to an Alcatel PBX, wich has an E1 to the outside. Located in Germany. zapata.conf: switchtype=euroisdn pridialplan=local prilocaldialplan=local overlapdial=yes signalling=pri_cpe .... With asterisk 1.0.2 I can call from a SIP phone to a phone connected to the Alcatel and the SIP number is correctly displayed at the caller.

Hi! I'm trying to setup a Wildcard TE110P with a PRI in The Netherlands. I get a Red Alarm on the line. Is there any way of debugging this? I've tried some configs that should work but without success. Is there any way of telling if the cabling is correct or what else the problem could be? Thanks!! Remco

I installed bristuff0.20-RC3 (which includes * 1.0.3 stable) It works fine until I disconnect the phone jack for the ISDN line. Even after plug it back in asterisk still reports that it could not create a zap channel when I try to dial out and the line gives an engaged tone when I try to dial. Re-starting asterisk doesn't solve this, I have to stop asterisk, unload the modules, reload

Hi list! While looking for the Snom 190 I found another phone, the Elmeg IP 290 (www.elmeg.de). Looking at the pictures & the specs they seem to be very similar beasts but the firmware is supposedly not interchangeable. Does anyone know the difference between the 2, do they work with Asterisk? The weird thing is that Elmeg has similar phones with the Snom look but they are ISDN only (no

Most people seem quite positive about Snom phones, I cannot share this opinion. The displays are dying quite often, and firmware is buggy. I have tried every firmware from 4.5 up to 5.x and 6.04 but keep having problems with phones locking up or rebooting during an ongoing conversation. REALLY annoying for a phone that is advertised / targeted as a business class phone

I'm getting a strange error on one of the two controllers on an AVM C2 card under chan_capi-cm-0.6.3. I have two ISDN controllers defined, both in the same group, both connections are UK ISDN2e Point to Point: On the third outbound call (both of the first two calls are handled by the second controller "ISDN2",) I get this error : chan_capi.c conf_error 0x2001 PLCI=0x301

Hi list! I'm sure the topic has been discussed but I could not find what I was looking for. What would be the best / easiest VPN software solution. I would like to install vpn software on the * server for roadwarriors to connect to with laptops running windows. Ideally the vpn solution will not require any additional software on the client side but will use IPSEC. (Ofcourse call quality