similar to: ZT_CHANCONFIG failed on channel 11: Function not implemented (38)

Displaying 20 results from an estimated 6000 matches similar to: "ZT_CHANCONFIG failed on channel 11: Function not implemented (38)"

2004 Apr 29
1
ZT_CHANCONFIG - function not implemented (38)
I'm trying to use ztcfg with the following zaptel.conf: span=1,1,0,esf,b8zs bchan=1-4 nethdlc 5-23 dchan=24 and I get "ZT_CHANCONFIG failed on channel 5: Function not implemented (38). This is on Debian 2.4.26. I have hdlc compiled as a module. Should hdlc be compiled into the kernel? Does anyone see a problem here? Thanks, -- Michael Welter Introspect Telephony Corp. Denver,
2005 Jun 22
4
FXS interfaces
Hi all, Does somebody know why no load modules to FXS? I used zaptel-1.0.7 version driver. [root@server1 zaptel-1.0.7]# modprobe wctdm ZT_CHANCONFIG failed on channel 3: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? /lib/modules/2.4.21-27.EL/misc/wcfxs.o: post-install wcfxs failed
2005 Sep 05
0
Re: Asterisk-Users Digest, Vol 14, Issue 22
Hi All I have problem with LIBMFCR2 for once Exchange I using Sangoma card, the firstly. my ssystem run successful with MFCR2, connected to E10 (Acatel Exchange), after that, i move connection connect to EWSD (Siemens), my system don't work. error protocol R2. my system: Asterisk CVS 1.1.X LibMFCR2 pre.005 and unicall-pre.005 this's my setting and my setting wanpipe1.conf
2005 Jun 21
3
FXS
Em (20:59:21), Asterisk Users Mailing List - Non-Commercial Discussion escreveu: >On Tue, Jun 21, 2005 at 08:09:52PM -0300, Alessandro wrote: >> >> Does Somebody know why no load modules to FXS? I used zaptel-1.0.7 >> version. > >What color are the modules? >Post your /etc/zaptel.conf > >-- >Mike Mike, The color is green, red ans bluw. Link
2004 Jul 16
3
Echo problem update - POSSIBLE SOLUTION
After speaking with several people, and even participating in a forum of several other people with echo issues, I thought I'd share what we've done (well actually what our chief R&D engineer, Brett Bourn has done...) First let me say that normal cheapy PC hardware couldn't be made to function with out echo. We tried on both the single port Digium T1 card and the 4 port Digium T1
2005 Jun 03
1
ztdummy errors on WBEL4
zaptel compiles fine (make linux26) but when I modprobe ztdummy I get the follow error. [root@localhost zaptel]# modprobe ztdummy Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device '/dev/zap/ctl' 1 error(s) detected FATAL: Error running install command for ztdummy System info: Linux localhost.localdomain 2.6.9-5.0.5.ELsmp #1 SMP Thu May 19 19:24:44
2006 Jan 12
1
No D-channels available! Using Primary on channel 16 anyway!
Hi! I have a E1 PRI connected to my TE400P card on span 1, and two channelbanks on span 3 and 4 and * 1.2. Every few hours I get this message and asterisk dies just after that: Warning: No D-channels available! Using Primary on channel 16 anyway! When this happens restarting zaptel and asterisk services, generally puts the system back online my zaptel.con reads: span=1,1,0,ccs,hdb3
2005 Sep 07
1
ztcfg Kills My Dial Tone
I'm using two Rhino channel banks (first 12FXO/12FXS, second 24FXS). These connect to a Digium TE210P card. I'm running kernel 2.6.10 and I've tried Asterisk (w/zaptel) 1.0.9, 1.2 beta, and CVS from today. The results are the same for all versions: Right after I reboot, and modprobe wct4xxp, my analog phone connected to port 13 of the first channel bank (first FXS port) gets a dial
2005 Mar 06
3
Zaptel.conf and multiple T1 woes
Hello. New to the list. We're in the process of deploying Asterisk. Actually, we're going live tomorrow, and I just found out that my Zaptel cards have been mis-configured. I'll preface this by saying that I have looked in the wiki, read through the samples, and attempted to call Digium (they're closed.) So I'm praying that someone on the list can help me out! I have two
2004 Dec 07
0
Zaptel HDLC (NetHDLC) errors on modprobe, Linux 2.6 kernel
I have my Linux 2.6 kernel with the necessary HDLC config and also recompiled zaptel accordingly. On modprobe, I get: Found a Wildcard: Digium Wildcard T100P T1/PRI Debug: sleeping function called from invalid context at mm/slab.c:2000 in_atomic():0[expected: 0], irqs_disabled():1 [<0211e605>] __might_sleep+0x82/0x8c [<02144643>] kmem_cache_alloc+0x1d/0x57 [<42ad7a2c>]
2005 Jun 17
2
Can't switch span to E1-mode
Hi, This error I got it just when I gonfigure zaptel support isdneuro 31 channels. But if I configure zaptel to support T1 and just 24 channels I have no problem. ######################################################################## #### # # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # loadzone = it span=1,1,0,ccs,hdb3,crc4 bchan=1-23 dchan=16
2005 Mar 24
0
NetHDLC + PRI
Is it possible to run NETHDLC and PRI signaling on the same 4 port T405P card? This is what I get when I try to start asterisk: == Parsing '/etc/asterisk/zapata.conf': Found Mar 24 10:48:53 ERROR[2368]: chan_zap.c:9435 setup_zap: Unknown signalling method 'pri_cpe' Mar 24 10:48:53 WARNING[2368]: chan_zap.c:9614 setup_zap: Ignoring switchtype Mar 24 10:48:53
2004 Dec 03
3
Two zaptel T1 cards: no clock from one
List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to
2006 Jun 06
1
Asterisk exit on startup
I'm having a problem with a new installation of asterisk 1.2.5 with a digium dual port T1 (span 1 connected to an outside line, and span 2 connected to a CAC access bank I channel bank with 24 fxs ports). When I start Asterisk (either from safe_asterisk or asterisk -vvvc) it will immediately exit after it initializes. It will start the logger, register applications and functions, register
2003 Oct 14
2
T100P to Adtran TA750 - No dialtone or ring
Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm
2003 Sep 13
1
ZT_CHANCONFIG failed on channel 1: Invalid argument (22)
no matter which way I have my /etc/zaptel.cfg this only started happening after a yesterdays CVS update to my zaptel source... Line 1: fxoks=1 Line 2: fxsks=2 Line 23: loadzone=us Line 28: defaultzone=us <End of File> Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) 2 channels
2004 Jul 02
0
TA750 + T100P configuration. flashing red alarm on t100p after running modprobe wct1xxp, ztcfg
(to mods: sorry for any extra work I've put you through. Posting from my work account, as proper) Hello all, I'm back. I've got that lucky feeling that this will all work out very soon, and I hope that that is true. The issue: In my * server I have a t100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm
2014 Sep 18
1
Asterisk 11.9.0 PRI no ring indications
Hopefully someone can point me in the correct direction. I had a 1.4x system die on me yesterday, while I was prepping a new machine to replace it. Took the machine on site yesterday and spent the day and part of the evening getting things working. This morning, I finished up converting my dial plan, knowing there'd be calls of things that I missed. While testing, I've noted that all
2005 Jul 08
3
McLeod Integrated T1 - no PRI?
Hello everyone, We have recently turned up a new T1 from McLeod (Midwestern CLEC). It is configured like so: /etc/zaptel.conf: loadzone=us defaultzone=us span=1,0,0,esf,b8zs ;(also tried 1,1,0,esf,b8zs) bchan=13-23 nethdlc=1-12 dchan=24 /etc/zapata.conf: switchtype=national context=pri-in signalling=pri_cpe group=1 channel => 13-23 I can get hdlc0 (and pvc0) up just fine after the
2003 Apr 16
0
How to pickup incoming calls immediately?
Hi, I set up a t1 from my sys75 to asterisk. After much experimentation I got it to work as e&m wink start. If dialing the trunk access code from the sys75 (a 5 - this is stripped on the s75), asterisk picks up and provides dial tone immediately. Here is the problem, after about 3 seconds that line switches into s,1 of the default context. If I dial (5)1234 very fast - before the switch to