similar to: Wildcard TE405P and TDM400 - TDM not working

Hi, all I have installed TDM400 with 1 FXS and 1 FXP ports. Now I am goig through documentation on how to configure it. It mentions 3 protocols: Loopstart, Groundstart and Koolstart. Which one do I use? Can someone send me sample zaptel.conf file for Australia? This will save me some time and will be used as a working example. Thanks, Rudolf

Hi, Some weird problem (or I'm too sleepy) happens with a tdm04B revision G (4fxo) Steps: modprobe zaptel modprobe wctdm ztcfg -vv /etc/zaptel.conf fxsls=1-4 # TDM04B defaultzone=us loadzone=us /etc/asterisk/zapata.conf signalling=fxs_ls group=1 context=incoming channel => 1-4 modprobe zaptel and wctdm load fine, however ztcfg -vv shows: 0 channels configured Im using centos 4.4 with

Folks, I recently swapped a TDM400 FXS card that was working perfectly into a new server (running recent CVS), and it's either misbehaving (unlikely), or I've missed something obvious (much more probable). Everything seems to be working, but I can't get any dialtone from it when I plug a phone into any of the 4 ports!! All of the jacks are lit (green lights) but they all seem dead

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

I just purchased a T100p from digium and a Carrier Access Access Bank 1 channel bank (12fxs/12fxo). I have the setup partially working thanks to some help from IRC. However I still have the following issues I can't seem to resolve 1. When calling into the system from the PSTN call hangup is not detected. * leaves line in use until it is shutdown. 2. When calling an analog phone connected to

I'm having a problem with a new installation of asterisk 1.2.5 with a digium dual port T1 (span 1 connected to an outside line, and span 2 connected to a CAC access bank I channel bank with 24 fxs ports). When I start Asterisk (either from safe_asterisk or asterisk -vvvc) it will immediately exit after it initializes. It will start the logger, register applications and functions, register

I have a system that I am trying to get a port on a Sangoma A104d card connected to an Adtran 850 with 5 FXS modules and 1 FXO module. A problem I am having is figuring out what cable should be used from the port on the Sangoma to the JP2 port on the Adtran. Tried was a cross-over T1 (1->4, 2->5, 4->1, 5->2) as well as a straight T1 (1->1, 2->2, 4->4, 5->5). Neither one

Hi, sorry for my insistence but this is a big problem for me..my steps for remove card are ok ? Thanks. ------ Salvatore. ----- Original Message ----- From: "Sasa" <sasa at shoponweb.it> To: <asterisk-users at lists.digium.com> Sent: Monday, November 26, 2007 4:25 PM Subject: [asterisk-users] Remove a TDM Card > Hi, I would like remove a Digium TDM2400P from

Hello, I'm running * on a very basic configuration. I have a Wildcard TE405P with the first T1 connected to a PRI line and the remaining three to Adtran TA750 channel banks with FXS modules. I successfully configured everything to work with a couple of Swissvoice IP10S handsets (MGCP) and analog extensions connected to the channel banks. The problem I'm having is that when I pick up any

I'm installing TE405P card. This is my zaptel.conf. -------------------------------------- span=1,0,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 loadzone = us defaultzone= us -------------------------------------- When i modprobe wct4xxp, -------------------------------------- PCI: Found IRQ 11 for device 02:0b.0 PCI: Sharing IRQ 11 with

I've been having trouble with making outbound calls to my TELCO from a TDM400 card (FXS KS signalling) after upgrading from 1.6-beta9 to 1.6.0. The problem is completely intermittent. When it fails, I get this message: [Nov 9 19:12:26] WARNING[18916] app_dial.c: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) At some point, it starts working, but I don't know what

Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much

Hi All, I've got an MD3200 modem which is working as a Zaptel FXO interface for Asterisk (X100P clone I believe). It seems to work, but on incoming or outgoing calls I can hear the other party ok but when I speak, I hear my voice echo back at me (quite quietly but it's distracting!) on everything I say. The other party doesn't seem to hear the echo - they just say I sound a bit quiet.

Hello. I am running asterisk 1.2.14 on a Dell poweredge with a Digium FXO/FXS card connected to 6 analog lines and using Linksys spa942 phones. My users are complaining of randomly disconnected calls, and when I watch the log (debug warning,notice,error), I don't see any cause. It looks like asterisk is seeing a hangup from the analog end. I have attached my zaptel.conf and zapata.conf.

I have TE405P span connected to a patton/digi 2977 T1/PRI port. Zaptel starts up fine without any errors. Libpri is installed as well. But I get the following when trying to load asterisk ------- Jul 3 19:30:26 ERROR[8192]: Signalling requested is PRI Signalling but line is in Unknown signalling 896 signalling Jul 3 19:30:26 ERROR[8192]: Unable to register channel '25-48' Jul

Hi all, I've got a TE410p connected via T1 to four channel banks (2 FXO and 2 FXS), no PRIs. Some users are complaining that they hear clicks and pops on the FXS lines, generally when they pick up the phone it's noisy. This happens only after a while, e.g. after a fresh restart of everything, all is fine but after some time these noises start appearing. From what I've read on the

Hi, I'm wondering why zttest shows Best: 99.976 -- Worst: 99.967 -- Average: 99.971469, Difference: 99.971469 Shouldn't it be 100% as timing is hardware and comes from PRI? Am I missing some kernel config? Regards, Atis My /etc/zaptel.conf is span=1,4,0,esf,b8zs span=2,3,0,esf,b8zs span=3,2,0,esf,b8zs span=4,1,0,esf,b8zs #lspci 07:03.0 Communication controller: Digium, Inc. Wildcard

Hi again, I'm trying to setup our non pri T1 (they call it a Long Distance T1), our current pbx has the signaling set to E&M, I can set em in zapata.conf, but I'm trying to track down the proper entries for the zaptel.conf file. The digium docs only show a PRI example. Our current system has these settings: Signalling: E&M Framing mode: ESF Line Coding: B8SZ here's my

After speaking with several people, and even participating in a forum of several other people with echo issues, I thought I'd share what we've done (well actually what our chief R&D engineer, Brett Bourn has done...) First let me say that normal cheapy PC hardware couldn't be made to function with out echo. We tried on both the single port Digium T1 card and the 4 port Digium T1

Hello, I am trying the setup the TDM01B card. 1 FXO. I connected it to a regular home line. in the /etc/zaptel.conf, I have fxsls=4 In the /etc/asterisk/zapata.conf I have: signaling=fxs_ls language=en group=1 context=default channel => 4 When I start asterisk, I get this error: ERROR[10376]: chan_zap.c:6584 mkintf; Signaling requested on channel 4 is FXO Loopstart but line is in FXS