similar to: Newbie question - can't get Asterisk to pick up incoming call

Hello, I am trying the setup the TDM01B card. 1 FXO. I connected it to a regular home line. in the /etc/zaptel.conf, I have fxsls=4 In the /etc/asterisk/zapata.conf I have: signaling=fxs_ls language=en group=1 context=default channel => 4 When I start asterisk, I get this error: ERROR[10376]: chan_zap.c:6584 mkintf; Signaling requested on channel 4 is FXO Loopstart but line is in FXS

Hi All, I've got an MD3200 modem which is working as a Zaptel FXO interface for Asterisk (X100P clone I believe). It seems to work, but on incoming or outgoing calls I can hear the other party ok but when I speak, I hear my voice echo back at me (quite quietly but it's distracting!) on everything I say. The other party doesn't seem to hear the echo - they just say I sound a bit quiet.

Im having a problem getting the 2 cards working together. I added the TDM with 3 FXO and 1 FXS board. The TE405p is working fine. THe TDM registers and identifies the FXO's and FXS but cant get them to go off hook. I hope someone can help. Asterisk seems to THINK its dialing it sends manager status as dialing, and it just sits there with no tones, on the phone dialing out. If I dial,

so i have been running v1-0 on all of my test boxes for about a month now testing iax/sip/res_xxx. I decided to put it into production so I updated a box that was running 0.9.? that had been working perfectly for months and low and behold the inbound line from telco now intermittantly doesn't clear and none of the other channels can dial out on that line. I have tested the line in this

Hello I have installed my new E100P card in the same machin with two TDM04B cards. I have followthe instructions on http://www.digium.com/index.php?menu=configuration#T_E100P_PRI This is my zapata.conf span=1,0,0,cas,ami fxsls=1-15,17-31 dchan=16 fxsks=32-39 loadzone = us defaultzone=us I do *modprobe zaptel wct1xxp wcfxs ans seems to work ok. * But when i do ztcfg -vvv i got Zaptel

Hi All, I have just migrated from Asterisk 1.0.0 to Asterisk 1.0.5 and I have an X100P installed. The old asterisk was working, but now the new version isn't picking up any calls! However, I did notice that after installation, I performed modprobe zaptel and modprobe wcfxo and they worked fine, but when I executed ztcfg, I get the following errors: ioctl(ZT_LOADZONE) failed: Invalid

Hello All, I have this strange problem, I can dial out with my sip phone and it seems to work relatively well, but when I call in, the line just rings and rings, I get no indication in asterisk that it's detecting an incoming call. The strange thing is that in ztmonitor 1 -vv the rx volume goes from around 99% when the line is idle to 0% as soon as the line starts ringing. I'm located

Hello. I am running asterisk 1.2.14 on a Dell poweredge with a Digium FXO/FXS card connected to 6 analog lines and using Linksys spa942 phones. My users are complaining of randomly disconnected calls, and when I watch the log (debug warning,notice,error), I don't see any cause. It looks like asterisk is seeing a hangup from the analog end. I have attached my zaptel.conf and zapata.conf.

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

Hello, I am having problems configuring a TDM400P 4 Port FXO card with groundstart signalling. The box has 2 X100P's, 1 TDM04B and 1 TDM40B. I can configure it for loopstart and it works, just not groundstart, which I need for this installation. What am I missing? Thanks! Mark /etc/zaptel.conf #two X100P FXO Cards # fxsls=1-2 # TDM400P 4 Port FXO (TDM04B) fxsgs=3-6 # TDM400P 4 Port

Hi, Some weird problem (or I'm too sleepy) happens with a tdm04B revision G (4fxo) Steps: modprobe zaptel modprobe wctdm ztcfg -vv /etc/zaptel.conf fxsls=1-4 # TDM04B defaultzone=us loadzone=us /etc/asterisk/zapata.conf signalling=fxs_ls group=1 context=incoming channel => 1-4 modprobe zaptel and wctdm load fine, however ztcfg -vv shows: 0 channels configured Im using centos 4.4 with

I just purchased a T100p from digium and a Carrier Access Access Bank 1 channel bank (12fxs/12fxo). I have the setup partially working thanks to some help from IRC. However I still have the following issues I can't seem to resolve 1. When calling into the system from the PSTN call hangup is not detected. * leaves line in use until it is shutdown. 2. When calling an analog phone connected to

Hi, Maybe someone has seen this before... I've installed a new T100P, but it doesn't seem to work. I've attached the T100P to an Adtran 750 using a crossover cable. The Adtran shows a red alarm on the T1 interface. The Adtran has been set to factory defaults with FXS cards in 1-3 and an FXO card in 5. The T100P shows no signs of life--the leds are not lit. Should I be seeing

Hi all, Does somebody know why no load modules to FXS? I used zaptel-1.0.7 version driver. [root@server1 zaptel-1.0.7]# modprobe wctdm ZT_CHANCONFIG failed on channel 3: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? /lib/modules/2.4.21-27.EL/misc/wcfxs.o: post-install wcfxs failed

I am connecting a t100p to a b8zs, superframe, loopstart t1. Previously I've attached to e&m wink and pri lines with no problems; however I seem to be missing something. Should it be fxols in the zaptel.conf (smartjack to x100p) or fxsls? With e&m wink the dnis set was 100, so it was easy to make an extension 100; and it would answer incoming calls. How do you get a loopstart to

Folks, I recently swapped a TDM400 FXS card that was working perfectly into a new server (running recent CVS), and it's either misbehaving (unlikely), or I've missed something obvious (much more probable). Everything seems to be working, but I can't get any dialtone from it when I plug a phone into any of the 4 ports!! All of the jacks are lit (green lights) but they all seem dead

I am having a problem with Red Alarms on X100P cards. The most frustrating thing is I can not duplicate the alarms, therefore am not sure how to solve it. I have read after searching posts and the web that you can try different signaling methods which may help alleviate the problem. There is fxsks (Which I am currently using), fxsgs, and fxsls While reading the Digium site about these different

Sorry to post such a newb set of questions but I have been hammering about trying to get Asterisk running on FC2 machine reading everything available (I think that is what stuffed me, shouldn't have read it all :-) ). Config FC2 running Asterisk 1.0.0, with the h323 compiled in and installed correctly. Amazingly enough I have everything compiled correctly and installed. I am running a

Hi List, I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6). I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4 and asterisk-1.2.17 When it's the time for ztcfg to do its job it complains with <ZT_SPANCONFIG failed on span 2: No such device or address (6)>

I am having problems with my zaptel channels on my fresh install of Asterisk 1.4.2 on Fedora core 6. I have a new Digium TDM400P with 2 FXO modules. Both dmesg and ztcfg -vvv show the FXO modules loading correctly: --------------------- Zaptel Version: 1.4.1 Echo Canceller: MG2 Configuration ====================== Channel map: Channel 03: FXS Loopstart (Default) (Slaves: 03) Channel 04: FXS