similar to: TDM400 lost after reboot

I had a working Asterisk 1.4.24.1 installation on SUSE 9 Linux but SIP only. I then downloaded and installed latest Zaptel and could not get Zaptel working. So I downloaded Asterisk again and re-installed. But still problems: Here is my ztcfg output: asterisk:/etc/asterisk # ztcfg -vvvvv Notice: Configuration file is /etc/zaptel.conf line 4: Unable to read Zaptel version information. Zaptel

I have had a TDM400 with 2 FXO and 2 FXS working for ages (>12 months). It has stopped working. All four green lights are still lit. I have rebuilt zaptel and asterisk and restarted but the problem persists. /sbin/ztcfg -vvvv Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 03:

Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above: 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b1d9:0003 Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at e800 [size=256]

Apparently asterisk cannot reboot gracefully (unattended) when using realtime.... MySQL RealTime: Failed to connect database server asterisk on 127.0.0.1. Check debug for more info. WARNING[3763]: MySQL RealTime: Couldn't establish connection. Check debug. Since asterisk starts before mysql it will never start any workaround for this? g Regards Greg Cirino

it appears the cvs for zaptel as of 12/13/04 am is missing at least 1 file -- wcfxs.c greg Regards Greg Cirino ___________________________________ Cirelle Enterprises Inc. 603-425-2221 www.cirelle.com Web Application Development & Design www.cirelle.net ProSpeed High Speed Dial-up - 6 Times Faster www.cedata.com Web, FTP, Email Hosting Services www.mlsbot.com NNEREN MLS IDX Services When

Hello I setup Asterisk@Home with purely VoIP and it worked fine. I then added an X100P card so I could call out / take inbound calls via PSTN and that went fine. But I have just added a TDM400P card (specifically a TDM30B) and now problems. Here is some of the output. Any ideas on what I should be looking at next? When I run genzaptelconf -s -d I get lots of erors on screen - bit I can

I am getting quite frustrated today, so please bear with me. I just installed Fedora Core 4 (was running RedHat 9 with a working Asterisk) now my Fedora does not appear to be recognizing my X100P (clone) at all. Hardware browser just shows them as unknown device. driver: hisax So, of course, my zaptel drivers do not work and therefore my asterisk does not work. any help would be greatly

Hi, Some weird problem (or I'm too sleepy) happens with a tdm04B revision G (4fxo) Steps: modprobe zaptel modprobe wctdm ztcfg -vv /etc/zaptel.conf fxsls=1-4 # TDM04B defaultzone=us loadzone=us /etc/asterisk/zapata.conf signalling=fxs_ls group=1 context=incoming channel => 1-4 modprobe zaptel and wctdm load fine, however ztcfg -vv shows: 0 channels configured Im using centos 4.4 with

Has anyone had success with the TDM400 in production? I have multiple boxes where these cards lock up and the only thing that will fix them is to unload *, modprobe -r wctdm, modprobe wctdm, load asterisk. Does not matter if it is a FXS/FXO module. I know this topic has been discussed many times before, but my questions is not "is anyone else having this problem" since I know that

I am trying to resolve a problem where grandstream phones (only) fail to register after a period of time. I have a mysql realtime setup that appears to work, but fails for no reason. before i classify the realtime system as unusable, I am trying to isolate the problem. One thing I have noticed is the odbc driver continues to load even though I have removed (from what I can tell) references to

does anybody have an idea what the difference and significance of sip seeding and registration is. g Regards Greg Cirino ___________________________________ Cirelle Enterprises Inc. 603-425-2221 www.cirelle.com Web Application Development & Design www.cirelle.net ProSpeed High Speed Dial-up - 6 Times Faster www.cedata.com Web, FTP, Email Hosting Services www.mlsbot.com NNEREN MLS IDX

Hello everybody! I have some problems with my Astersk. I have an analogical OpenVox card and A Billion ISDN card (with mISDN). I load the modules with modprobe zaptel and modprobe wctdm. When I run ztcfg -vv I have this: Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: No

Hi, I'm curious what chip Digium is using in the latest TDM400 cards. Specifically, to my recollection, they used to use the TigerJet 320G, however somewhat recently, Tigerjet was bought out, and now the 320G is no longer produced. Maybe a better question is: is there a way I can take the latest DAHDI source and get a list of supported chipsets from it? Thanks. MCH -------------- next part

I have fixed this before, but I cannot for the life of me remember how I did it. I have a TDM400P with one fxo module and one fxs module. I setup Asterisk @Home and everything works fine, except when I try and call out. If I call out with a SIP phone it calls the zap extension and not the pstn line? If I take the zap extension offhook and call with the SIP phone it dials out the pstn line

can anybody identify why the CLI is issuing a failure message while debug shows everything is fine???? this makes no sense to me. also, why is the username being updated? this has got to be wrong from CLI -- SIP Seeding '52221' at 52221@192.168.70.26:5060 for 3600 -- SIP Seeding '52221' at 52221@192.168.70.26:5060 for 3600 Dec 24 12:16:35 NOTICE[15776]:

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

I recently swapped 2 FXO modules on to what had previously been a 4 FXS version of the TDM400 board. The FXS ports are recognized - the FXO ports don't appear to be recognized (ie modprobe wcfxo and ztcfg both say channel 1 isn't there). Has anyone experienced this problem? All software is current as of this AM. If the old FXS modules are re-installed all works just dandy (other than

Is there anything special needed to load up a TDM10B card?? I got the card today.. Took it from the box, put it into a PCI slot.. connected the power to the card and booted the PC.. I have removed the X100P to avoid confusion and I have the following in the config files.. in /etc/zaptel.conf # For the X100P #fxsks=1 # For the TDM10B fxoks=1 in /etc/asterisk/zapata.conf [channels]

I heard Sipura had really awesome documentation on the SPA-2000 and SPA-3000, but you have to email them for it. When I did, they said I had to get it from a reseller. It's been a while since I bought my units, I don't even remember where or who they were bought from. Can somebody email me the documentation for these devices? I'm quite interested in knowing what every one of their 200+

Folks, I have a Xen Asterisk VM with a TDM400 card. When I try to run dahdi_cfg, I get: tempest:~# dahdi_cfg -vvv DAHDI Tools Version - 2.2.0 DAHDI Version: 2.2.0 Echo Canceller(s): Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Echo Canceler: none) (Slaves: 01) Channel 03: FXS Kewlstart (Default) (Echo Canceler: none) (Slaves: 03) Channel 04: FXS